Copyright Notice The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice.
Smartphone Application is a smart web gadget that works as a shopping navigator and provides specs comparison for IT buyers. With a simple tap of the smartphone, you'll efficiently locate your ideal products from a wide variety of choices and, if product details are required, you may easily download user manuals within minutes.
Safety Instructions ■ Always read the safety instructions carefully. ■ Keep this User’s Manual for future reference. ■ Keep this equipment away from humidity. ■ Lay this equipment on a reliable flat surface before setting it up. ■ The openings on the enclosure are for air convection hence protects the equipment from overheating.
Page 5
FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 6
Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment and its antenna should be installed and operated with minimum distance 20 cm between the radiator and your body. This equipment and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
Battery Information European Union: Batteries, battery packs, and accumulators should not be disposed of as unsorted household waste. Please use the public collection system to return, recycle, or treat them in compliance with the local regulations. Taiwan: For better environmental protection, waste batteries should be collected separately for recycling or special disposal.
Page 8
WEEE (Waste Electrical and Electronic Equipment) Statement ENGLISH To protect the global environment and as an environmentalist, MSI must remind you that... Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2002/96/EC, which takes effect on August 13, 2005, products of “electrical and electronic equipment”...
Page 9
ESPAÑOL MSI como empresa comprometida con la protección del medio ambiente, recomienda: Bajo la directiva 2002/96/EC de la Unión Europea en materia de desechos y/o equipos electrónicos, con fecha de rigor desde el 13 de agosto de 2005, los productos clasificados como “eléctricos y equipos electrónicos”...
Page 10
TÜRKÇE Çevreci özelliğiyle bilinen MSI dünyada çevreyi korumak için hatırlatır: Avrupa Birliği (AB) Kararnamesi Elektrik ve Elektronik Malzeme Atığı, 2002/96/EC Kararnamesi altında 13 Ağustos 2005 tarihinden itibaren geçerli olmak üzere, elektrikli ve elektronik malzemeler diğer atıklar gibi çöpe atılamayacak ve bu elektonik cihazların üreticileri, cihazların kullanım süreleri bittikten sonra ürünleri geri toplamakla yükümlü...
English Thank you for choosing the Z87-G43 GAMING/ H87-G43 GAMING/ B85-G43 GAMING Series (MS-7816 v2.X) ATX motherboard. The Z87-G43 GAMING/ H87-G43 GAMING/ B85-G43 GAMING Series motherboards are based on Intel Z87/ H87/ B85 chipset for optimal system efficiency. Designed to ®...
4x DDR3 memory slots supporting up to 32GB ■ Supports DDR3 3000(OC)/ 2800(OC)/ 2666(OC)/ 2600(OC)/ Support 2400(OC)/ 2200(OC)/ 2133(OC)/ 2000(OC)/ 1866(OC)/ 1600/ 1333/ 1066 MHz OC is for Z87-G43 GAMING only. ■ Dual channel memory architecture ■ Supports non-ECC, un-buffered memory ■...
Page 17
■ CPU/System fan speed detection Monitor ■ CPU/System fan speed control BIOS ■ 64 Mb flash (for Z87-G43 GAMING) ■ 128 Mb flash (for H87-G43 GAMING/ B85-G43 GAMING) Features ■ UEFI AMI BIOS ■ ACPI 5.0, PnP 1.0a, SM BIOS 2.7, DMI 2.0 ■...
Page 18
Special ■ Military Class 4 ■ OC Genie 4 Features ■ CLICK BIOS 4 ■ All Solid CAPs ■ AMD CrossFire ■ PCI Express Gen 3 ■ Sound Blaster Cinema (optional) ■ Super RAID ■ USB 3.0 ■ SATA 6Gb/s ■...
Page 20
Connectors Reference Guide Port Name Port Type Page Back Panel I/O Ports En-7 CPU Socket LGA1150 CPU Socket En-10 CPUFAN1~2,SYSFAN1~3 Fan Power Connectors En-19 DIMM1~4 DDR3 Memory Slots En-13 JAUD1 Front Panel Audio Connector En-23 JBAT1 Clear CMOS Jumper En-24 JCI1 Chassis Intrusion Connector En-22...
Back Panel Quick Guide PS/2 Keyboard/ Mouse Combo LAN Port Port USB 2.0 Port Line-In RS-Out USB 2.0 Port Line-Out CS-Out SS-Out USB 2.0 Port HDMI DVI-D Port USB 3.0 Port ▶ PS/2 Keyboard/Mouse Combo Port A combination of PS/2 mouse/keyboard DIN connector for a PS/2 mouse/keyboard.
Page 22
▶ USB 3.0 Port USB 3.0 port is backward-compatible with USB 2.0 devices. It supports data transfer rate up to 5 Gbit/s (SuperSpeed). Important In order to use USB 3.0 devices, you must connect to a USB 3.0 port. If a USB cable is used, it must be USB 3.0 compliant.
CPU (Central Processing Unit) Introduction to the LGA 1150 CPU The surface of the LGA 1150 CPU has two notches and a golden triangle to assist in correctly lining up the CPU for motherboard placement. The golden triangle is the Pin 1 indicator. Notch Notch Golden triangle is the Pin 1 indicator...
Page 24
CPU & Heatsink Installation When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink is necessary to prevent overheating and maintain system stability. Follow the steps below to ensure correct CPU and heatsink installation. Wrong installation can damage both the CPU and the motherboard.
Page 25
3. Align the notches with the socket alignment keys. Lower the CPU straight down, without tilting or sliding the CPU in the socket. Inspect the CPU to check if it is properly seated in the socket. 4. Close and slide the load plate under the retention knob. Close and engage the load lever.
Page 26
7. Locate the CPU fan connector on the motherboard. 8. Place the heatsink on the motherboard with the fan’s cable facing towards the fan connector and the fasteners matching the holes on the motherboard. CPU fan connector 9. Push down the heatsink until the four fasteners get wedged into the holes on the motherboard.
Memory These DIMM slots are used for installing memory modules. For more information on compatible components, please visit http://www.msi.com/service/test-report/ DIMM1 DIMM2 DIMM3 DIMM4 Video Demonstration Watch the video to learn how to install memories at the address below. http://youtu.be/76yLtJaKlCQ Dual-Channel mode Population Rule In Dual-Channel mode, the memory modules can transmit and receive data with two data bus channels simultaneously.
Mounting Screw Holes When installing the motherboard, first install the necessary mounting stands required for an motherboard on the mounting plate in your computer case. If there is an I/O back plate that came with the computer case, please replace it with the I/O backplate that came with the motherboard package.
Power Supply Video Demonstration Watch the video to learn how to install power supply connectors. http://youtu.be/gkDYyR_83I4 JPWR1~2: ATX Power Connectors These connectors allow you to connect an ATX power supply. To connect the ATX power supply, align the power supply cable with the connector and firmly press the cable into the connector.
Video/ Graphics Cards If available, this motherboard takes advantage of the CPU’s integrate graphics processor, but discrete video cards can be installed by way of the motherboard’s expansion slots. Adding on one or more discrete video cards will significantly boost the system’s graphics performance.
Internal Connectors SATA1~6: SATA Connector This connector is a high-speed SATA interface port. Each connector can connect to one SATA device. SATA devices include disk drives (HDD), solid state drives (SSD), and optical drives (CD/ DVD/ Blu-Ray). Video Demonstration Watch the video to learn how to Install SATA HDD. http://youtu.be/RZsMpqxythc SATA2 SATA1...
CPUFAN1~2,SYSFAN1~3: Fan Power Connectors The fan power connectors support system cooling fans with +12V. If the motherboard has a System Hardware Monitor chipset on-board, you must use a specially designed fan with a speed sensor to take advantage of the CPU fan control. Remember to connect all system fans.
JFP1, JFP2: System Panel Connectors These connectors connect to the front panel switches and LEDs. The JFP1 connector is compliant with the Intel Front Panel I/O Connectivity Design Guide. When ® installing the front panel connectors, please use the optional M-Connector to simplify installation.
JUSB1~2: USB 2.0 Expansion Connector (JUSB2 is optional) This connector is designed for connecting high-speed USB peripherals such as USB HDDs, digital cameras, MP3 players, printers, modems, and many others. Important Note that the VCC and GND pins must be connected correctly to avoid possible damage.
Page 36
JTPM1: TPM Module Connector This connector connects to a optional TPM (Trusted Platform Module) Module. Please refer to the TPM security platform manual for more details and usages. JCI1: Chassis Intrusion Connector This connector connects to the chassis intrusion switch cable. If the computer case is opened, the chassis intrusion mechanism will be activated.
JAUD1: Front Panel Audio Connector This connector allows you to connect the front audio panel located on your computer case. This connector is compliant with the Intel Front Panel I/O Connectivity Design ® Guide. JLPT1: Parallel Port Connector This connector is used to connect an optional parallel port bracket. The parallel port is a standard printer port that supports Enhanced Parallel Port (EPP) and Extended Capabilities Parallel Port (ECP) mode.
JCOM1: Serial Port Connector This connector is a 16550A high speed communication port that sends/receives 16 bytes FIFOs. You can attach a serial device. Jumper JBAT1: Clear CMOS Jumper There is CMOS RAM onboard that is external powered from a battery located on the motherboard to save system configuration data.
Drivers and Utilities After you install the operating system you will need to install drivers to maximize the performance of the new computer you just built. MSI motherboard comes with a Driver Disc. Drivers allow the computer to utilize your motherboard more efficiently and take advantage of any special features we provide.
BIOS Setup CLICK BIOS is developed by MSI that provides a graphical user interface for setting parameters of BIOS by using the mouse and the keybord. With the CLICK BIOS, users can change BIOS settings, monitor CPU temperature, select the boot device priority and view system information such as the CPU name, DRAM capacity, the OS version and the BIOS version.
Page 41
Overview After entering BIOS, the following screen is displayed. Temperature monitor Language System information Model name Virtual OC Genie Button Boot device priority bar BIOS menu selection BIOS menu selection Menu display ▶ Temperature monitor Shows the temperatures of the processor and the motherboard. ▶...
Page 42
▶ Boot device priority bar You can move the device icons to change the boot priority. High priority Low priority ▶ Menu display This area provides BIOS settings and information to be configured. ▶ Virtual OC Genie Button Enables or disables the OC Genie function by clicking on this button. When enabled, this button will be light.
Page 43
Operation You can control BIOS settings with the mouse and the keyboard. The following table lists and describes the hot keys and the mouse operations. Hot key Mouse Description <↑↓→← > Select Item Move the cursor <Enter> Select Icon/ Field Click/ Double-click the left button...
Page 44
▶ Adjust CPU Base Clock Strap [Auto] (Z87-G43 GAMING) Sets the CPU Base Clock Strap. You may overclock the CPU Base Clock by adjusting this value. Please note that overclocking behavior and stability is not guaranteed. This item can only be changed if the processor supports this function.
Page 45
CPU will run the adjusted CPU base clock after reboot. [Immediate] CPU runs the adjusted CPU base clock immediately. ▶ CPU PCIE PLL [Auto] (Z87-G43 GAMING) Selects a PLL (Phase Lock Loop) mode for CPU PCIe. This item appears when the installed CPU supports this setting. [Auto] This setting will be configured automatically by BIOS.
Page 46
▶ Adjust Ring Ratio [Auto] Sets the ring ratio. The valid value range depends on the installed CPU. ▶ Adjusted Ring Frequency Shows the adjusted Ring frequency. Read-only. ▶ Adjust GT Ratio [Auto] Sets the integrated graphics ratio. The valid value range depends on the installed CPU.
Page 47
▶ Memory Fast Boot [Auto] Enables or disables the initiation and training for memory every booting. [Auto] This setting will be configured automatically by BIOS. [Enabled] Memory will completely imitate the archive of first initiation and first training. After that, the memory will not be initialed and trained when booting to accelerate the system booting time.
Page 48
▶ CPU VRM Over Temperature Protection [Enabled] Enables or disables the CPU VRM over-temperature protection. [Enabled] Sets the temperature limit on CPU VRM for over-temperature protec- tion. [Disabled] Disables this function. ▶ Digital Compensation Level [Auto] Sets the current compensation level for CPU PWM when the MOS phases are changed.
Page 49
▶ CPU Core Voltage Offset Mode/ CPU Ring Voltage Offset Mode/ CPU GT Voltage Offset Mode/ CPU SA Voltage Offset Mode/ CPU IO Analog Voltage Offset Mode/ CPU IO Digital Voltage Offset Mode [Auto] Selects the voltage offset modes. [Auto] This setting will be configured automatically by BIOS.
Page 50
▶ CPU Specifications Press <Enter> to enter the sub-menu. This sub-menu displays the information of installed CPU. You can also access this information menu at any time by pressing [F4]. Read only. ▶ CPU Technology Support Press <Enter> to enter the sub-menu. The sub-menu shows what the key features does the installed CPU support.
Page 51
▶ Hardware Prefetcher [Enabled] Enables or disables the hardware prefetcher (MLC Streamer prefetcher). [Enabled] Allows the hardware prefetcher to automatically pre-fetch data and instructions into L2 cache from memory for tuning the CPU perfor- mance. [Disabled] Disables the hardware prefetcher. ▶...
Page 52
▶ LakeTiny Feature [Disabled] (optional) Enables or disables Intel Lake Tiny technology with iRST for SSD. This item appears when "Intel C-State" is enabled. [Enabled] Enhance the dynamic IO load adjusted performance for accelerating the SSD speed. [Disabled] Disables this feature. Note: The following items will appear when "Intel Turbo Boost "...
한국어 Z87-G43 GAMING/ H87-G43 GAMING/ B85-G43 GAMING 시리즈 (MS-7816 v2.X) ATX 메인보드를 선택해 주셔서 감사합니다. Z87-G43 GAMING/ H87- G43 GAMING/ B85-G43 GAMING 시리즈 메인보드는 최적의 효율을 위해 Intel Z87/ H87/ B85 칩셋에 기반을 둔 제품입니다. 고급 Intel LGA1150 프로 ®...
Page 55
8 핀 ATX 12V 전원 커넥터 1개 넥터 ■ SATA 커넥터 6개 ■ USB 2.0 커넥터 2개 (외 Z87-G43 GAMING & H87-G43 GAMING용 USB 2.0 4포트 지원) ■ USB 2.0 커넥터 1개 (외 B85-G43 GAMING용 USB 2.0 2포트 지원) ■...
Page 56
소프트웨어 ■ 드라이버 ■ Command Center Super Charger Super RAID Live Update 5 Fast Boot ■ 7-ZIP ■ Intel Turbo Boost Monitor ■ Intel Extreme Tuning Utility ■ Intel Small Business Advantage (옵션) ■ Sound Blaster Cinema (옵션) ■ Norton Internet Security Solution ■...
Page 58
커넥터 참조 목록 포트 이름 포트 타입 페이지 후면 패널 I/O 포트 Kr-7 CPU 소켓 LGA1150 CPU 소켓 Kr-10 CPUFAN1~2,SYSFAN1~3 팬 전원 커넥터 Kr-19 DIMM1~4 DDR3 메모리 슬롯 Kr-13 JAUD1 전면 패널 오디오 커넥터 Kr-23 JBAT1 CMOS 클리어 점퍼 Kr-24 JCI1 섀시...
후면 패널 PS/2 키보드 /마 LAN 포트 우스 콤보 포트 USB 2.0 포트 RS 출력 라인 입력 USB 2.0 포트 라인 출력 CS 출력 마이크 SS 출력 HDMI DVI-D 포트 USB 2.0 포트 USB 3.0 포트 ▶ PS/2 키보드/마우스 콤보 포트 PS/2 마우스/키보드...
Page 60
▶ USB 3.0 포트 USB 3.0 포트는 USB 2.0 장치와 호환할 수 있습니다. 데이터 전송 속도 최대 5 Gbit/s 지원(superspeed) 중요사항 USB 3.0 장치는 USB 3.0포트에 연결해야 합니다.USB 케이블이 USB 3.0 규격을 준수 하는지 확인하시기 바랍니다. ▶ LAN 포트 ▶ 표준...
CPU (중앙 처리 장치) LGA 1150 CPU 소개 메인보드에 CPU를 정확하게 배치하기 위하여 LGA 1150 CPU 표면에 2개의 요철 과 하나의 노란색 삼각형이 있습니다. 노란색 삼각형은 1번 핀을 나타냅니다. 요철 요철 노란색 삼각형은 1번 핀을 나타냅니다. 중요사항 과열 과열은 CPU와 시스템을 심각하게 손상시킬수 있으니 CPU가 과열되지 않도록 쿨러팬 이...
Page 62
CPU 및 히트싱크 설치 CPU 설치 시, CPU 히트싱크를 반드시 설치하세요. CPU 히트싱크는 과열을 방지하고 시스템 성능을 유지하는데 꼭 필요합니다.아래의 순서에 따라 CPU 및 히트싱크를 정확 하게 설치하세요. 잘못 설치할 경우 CPU와 메인보드가 손상될수 있습니다. 데모 동영상 CPU 및 히트싱크 설치에 대한 동영상을 참조하려면 아래의 웹사이트 를...
Page 63
3. 요철을 올바른 방향으로 소켓 정렬 키에 맞춘 후 CPU를 소켓에 내려놓습니다. CPU가 소켓에 제대로 장착되었는지 확인하세요. 4. 로드 플레이트를 닫고 노브에 고정한 후 로드 레버를 아래로 눌러 고정탭에 고정합 니다. CPU 요철 정렬 키 노브 5. 로드 레버를 아래로 누르면 PnP 캡이 CPU 소켓에서 자동으로 분리됩니다. PnP 캡 을...
Page 64
7. 메인보드에 CPU 팬 커넥터를 장착합니다. 8. 팬의 선이 팬 커넥터 쪽을 향하고 고정핀이 메인보드의 홀에 꼭 맞게 히트싱크를 메 인보드에 장착합니다. CPU 팬 커넥터 9. 4개의 고정핀이 메인보드의 홀에 완전히 박힐 때까지 히트싱크를 누릅니다. 4개의 고정핀을 눌러 히트싱크를 고정합니다. 고정핀이 올바른 위치에 고정되었다면 닫히 는...
메모리 DIMM 슬롯은 메모리 모듈을 설치하는데 사용됩니다. 호환 가능한 부품에 대한 자세한 내용은 http://www.msi.com/service/test-report/를 참조하세요. DIMM1 DIMM2 DIMM3 DIMM4 데모 동영상 메모리 설치에 대한 동영상을 참조하려면 아래의 웹사이트를 방문하세요. http://youtu.be/76yLtJaKlCQ 듀얼 채널 모드 배포 규칙 듀얼 채널 모드에서는 메모리 모듈이 2개의 데이터 버스 채널을 통해 데이터를 동시에 전송...
장착 스크류 홀 메인보드를 설치할 때, 먼저 컴퓨터 케이스의 베이스 플레이트에 메인보드 설치를 위한 지지대를 장착합니다. 컴퓨터 케이스와 함께 제공되는 I/O 쉴드(백 플레이트)가 있을 경 우 메인보드 패키지와 함께 제공되는 I/O 쉴드(백 플레이트)로 교체하세요. I/O 쉴드(백 플레이트)는 스크류가 필요없이 컴퓨터 케이스에 쉽게 들어가야 합니다. 장착 플레이트 의...
전원 공급 장치 데모 동영상 전원 공급 장치 커넥터 설치에 대한 동영상을 참조하려면 아래의 웹사이트를 방문하세요. http://youtu.be/gkDYyR_83I4 JPWR1~2: ATX 전원 커넥터 이 커넥터를 사용하여 ATX 전원 공급 장치를 연결할수 있습니다. ATX 전원 공급 장치 를 연결하려면 커넥터에 전원 공급 케이블을 정렬하고 케이블을 커넥터 안쪽으로 꼭 눌 러줍니다.만약...
확장 슬롯 이 메인보드에는 별도의 그래픽, 오디오 카드등과 같은 확장 카드 사용을 위한 포트들 이 다수 포함되어 있습니다. PCI_E1~E4: PCIe 확장 슬롯 PCIe 슬롯은 PCIe 인터페이스 확장 카드를 지원합니다. PCIe 3.0 x16 슬롯 PCIe 2.0 x16 슬롯 PCIe 2.0 x1 슬롯 PCI1~3: PCI 확장...
비디오/ 그래픽 카드 가능한 경우, 메인보드는 CPU의 통합 그래픽 프로세서를 활용하지만 별도의 그래픽 카 드도 메인보드의 확장 슬롯에 설치할수 있습니다. 별도의 비디오 카드를 하나 또는 하 나 이상 추가하면 시스템의 그래픽 성능을 크게 높일수 있습니다. 최적의 호환성을 위 해 MSI 그래픽 카드를 사용할 것을 권장합니다. 데모...
내장 커넥터 SATA1~6: SATA 커넥터 이 커넥터는 고속 SATA 인터페이스 포트에 사용됩니다.각 커넥터는 하나의 SATA 장 치에 연결할수 있습니다. SATA 장치는 디스크 드라이브(HDD), 솔리드 스테이트 드라 이브(SSD)및 옵티컬 드라이브 (CD/ DVD/ 블루 레이)를 포함합니다. 데모 동영상 SATA HDD 설치에 대한 동영상을 참조하려면 아래의 웹사이트를...
Page 71
CPUFAN1~2,SYSFAN1~3: 팬 전원 커넥터 팬 전원 커넥터는 +12V의 시스템 쿨링 팬을 지원합니다. 메인보드에 시스템 하드웨어 모니터 칩셋이 온보드 되어 있는 경우 CPU 팬 제어를 활용하기 위하여 속도 센서가 있 는 특별히 디자인된 팬을 사용해야 합니다. 시스템 팬은 전부 연결하세요. 만일 시스템 팬을...
Page 72
JFP1, JFP2: 시스템 패널 커넥터 이 커넥터는 전면 패널 스위치 및 LED에 연결됩니다. JFP1커넥터는 Intel Front Panel ® I/O Connectivity Design Guide를 준수합니다. 전면 패널 커넥터 설치를 간편히 하기 위 하여 옵션인 M-커넥터를 사용하세요. 컴퓨터 케이스로 부터 모든 선을 M-커넥터에 연 결한...
Page 73
JUSB1~2: USB 2.0 확장 커넥터 (JUSB2는 옵션입니다.) 이 커넥터는 USB HDD,디지컬 카메라, MP3 플레이어,프린터, 모뎀 등과 같은 고속 USB 주변 장치를 연결하도록 디자인 되었습니다. 중요사항 VCC 및 GND의 핀을 정확히 연결하여야 손상을 방지할수 있습니다. JUSB3: USB 3.0 확장 커넥터 USB 3.0 포트는 USB 2.0 장치와 호환할수 있습니다.데이터 전송속도 최대 5Gbits/s (SuperSpeed)를...
Page 74
JTPM1: TPM 모듈 커넥터 이 커넥터는 옵션인 TPM (Trusted Platform Module) 모듈에 연결됩니다. 자세한 내용과 사용법은 TPM 보안 플랫폼 설명서를 참조하세요. JCI1: 섀시 침입 커넥터 이 커넥터는 섀시 침입 스위치 케이블에 연결됩니다. 컴퓨터 케이스가 열리는 경우, 섀 시 침입 메커니즘이 활성화됩니다. 시스템이 이 상태를 기록하고 화면에 경고 메시지가 나타납니다.
Page 75
JAUD1: 전면 패널 오디오 커넥터 이 커넥터를 사용하여 컴퓨터 케이스에 있는 전면 오디오 패널을 연결할 수 있으며, 이 커넥터는 Intel Front Panel I/O Connectivity Design Guide를 준수합니다. ® JLPT1: 페러렐 포트 커넥터 이 커넥터는 옵션인 페러렐 포트 브래킷을 연결하는데 사용됩니다. 이 페러렐 포트는 표준...
JCOM1: 시리얼 포트 커넥터 이 커넥터는 16550A 고속 통신 포트로서 16바이트의 FIFO를 송수신합니다. 시리얼 장 치를 연결할 수 있습니다. 점퍼 JBAT1: CMOS 클리어 점퍼 보드에 시스템 구성 데이터를 유지하기 위해 외부 배터리로부터 전원을 공급 받는 CMOS RAM이 있습니다. CMOS RAM의 경우, 시스템을 켤 때마다 시스템이 OS를 자 동으로...
드라이버 및 유틸리티 구입한 컴퓨터의 성능을 최대화하려면 운영 체제를 설치한 다음 드라이버도 설치해야 합니다. 드라이버 디스크는 MSI 메인보드와 함께 제공됩니다. 드라이버를 설치하여 메 인보드를 보다 효율적으로 활용하고 모든 특별 기능을 사용할 수 있습니다. 번들 보안 프로그램을 설치하여 바이러스로부터 컴퓨터를 보호할 수 있습니다. 그 외에 도...
BIOS 설정 CLICK BIOS는 MSI에서 개발한 그래픽 사용자 인터페이스로서 마우스와 키보드를 사 용하여 BIOS를 설정할수 있습니다. CLICK BIOS를 사용하여 BIOS 설정을 변경하고 CPU 온도를 감시할수 있으며 부팅 장 치의 우선순위를 선택하고 CPU 이름, DRAM 용량, OS버전 및 BIOS 버전 등과 같은 시 스템...
Page 79
개요 BIOS를 시작하면 아래의 화면이 표시됩니다. 온도 모니터 언어 시스템 정보 모델 명 Virtual OC Genie 버튼 부팅 장치 우 선순위 바 BIOS 선택 메뉴 BIOS 선택 메뉴 메뉴 디스플레이 ▶ 온도 모니터 이 블록은 프로세서와 메인보드의 온도를 표시합니다. ▶ 언어...
Page 80
▶ 부팅 장치 우선순위 바 장치 아이콘을 이동하여 부팅 순위를 변경합니다. 높은 순위 낮은 순위 ▶ 메뉴 디스플레이 이 영역은 BIOS 설정 및 구성 정보를 제공합니다. ▶ Virtual OC Genie 버튼 이 버튼을 클릭하여 OC Genie 기능을 활성화 또는 비활성화합니다. 기능이 활성화 되 면...
Page 81
컨트롤 마우스 또는 키보드를 사용하여 BIOS 설정을 제어할수 있습니다.아래 그림은 핫 키와 마우스 사용에 대한 설명입니다. 핫 키 마우스 설명 <↑↓→← > 항목 선택 커서 이동 <Enter> 아이콘/ 필드 선택 클릭/ 왼쪽 버튼 더 블 클릭 <Esc> 종료 메뉴로 가거나 이전 메뉴로 이동 오른쪽...
Page 82
이 항목은 현재 CPU Base Clock Strap을 표시하며 읽기 전용입니다. 프로세서가 이 기 능을 지원하는 경우에만 이 항목을 변경할 수 있습니다. ▶ Adjust CPU Base Clock Strap [Auto] (Z87-G43 GAMING) 이 항목을 사용하여 CPU Base Clock Strap을 설정할수 있습니다. 값을 조정하여 CPU 베이스 클럭을 오버클럭할 수 있지만 오버클로킹의 작동이나 안정성은 보증하지 않습니...
Page 83
재부팅 후 조정된 CPU 베이스 클럭을 실행합니다. [Immediate] CPU는 즉시 조정된 CPU 베이스 클럭을 실행합니다. ▶ CPU PCIE PLL [Auto] (Z87-G43 GAMING) 이 항목을 사용하여 CPU PCIe의 PLL (Phase Lock Loop) 모드를 선택합니다. 이 항목은 설치된 CPU가 이 설정을 지원하는 경우 나타납니다. [Auto] 이...
Page 84
▶ Adjust Ring Ratio [Auto] 이 항목을 사용하여 링 비율을 설정합니다. 유효한 값 범위는 설치된 CPU에 따라 달라 집니다. ▶ Adjusted Ring Frequency 이 항목은 조정된 링 주파수를 표시합니다.(읽기 전용) ▶ Adjust GT Ratio [Auto] 이 항목을 사용하여 통합 그래픽 클럭의 배수를 설정합니다. 유효한 값 범위는 설치된 CPU에...
Page 85
▶ Memory Fast Boot [Auto] 매번 부팅할 때 메모리의 트레이닝 개시를 활성화 또는 비활성화합니다. [Auto] 이 설정은 BIOS에서 자동으로 구성됩니다. [Enabled] 메모리는 첫번째 시작과 첫 트레이닝을 완전히 모방합니다.이후에 시스템 부팅 시간을 가속화하면서 부팅 할 경우, 메모리는 트레이닝되지 않습니 다. [Disabled] 메모리가...
Page 86
▶ CPU VRM Over Temperature Protection [Enabled] CPU VRM 과온도 보호 기능을 활성화 또는 비활성화합니다. [Enabled] CPU VRM 과온도 제한 값을 설정합니다. [Disabled] 이 기능을 비활성화합니다. ▶ Digital Compensation Level [Auto] 이 항목을 사용하여 MOS 단계 변경에 따른 CPU PWM의 전류 보상 레벨을 설정할 수 있습니다.
Page 87
▶ CPU Core Voltage Offset Mode/ CPU Ring Voltage Offset Mode/ CPU GT Voltage Offset Mode/ CPU SA Voltage Offset Mode/ CPU IO Analog Voltage Offset Mode/ CPU IO Digital Voltage Offset Mode [Auto] 이 항목을 사용하여 전압 오프셋 모드를 선택할 수 있습니다. [Auto] 이...
Page 88
▶ CPU Specifications <Enter>를 눌러 서브 메뉴를 시작합니다. 이 서브 메뉴는 설치된 CPU의 정보를 표시합 니다. 사용자는 언제든지 [F4]키를 눌러 정보 메뉴에 액세스할수 있습니다. ▶ CPU Technology Support <Enter>를 눌러 서브 메뉴를 시작합니다. 이 서브 메뉴는 설치된 CPU가 지원하는 주 요...
Page 89
▶ Intel Virtualization Tech [Enabled] 이 항목을 사용하여 Intel Virtualization technology(인텔 가상화 기술)을 활성화 또는 비활성화할 수 있습니다. [Enabled] 이 기술을 활성화하면 플랫폼이 독립적인 파티션에서 여러 운영체제 를 실행할 수 있고 시스템은 여러개의 가상화 시스템으로 작동합니 다. [Disabled] 이 기능을 비활성화합니다. ▶...
Page 90
▶ Package C State limit [Auto] 시스템 유휴 상태에서 전력 절약을 위한 CPU C-state 모드를 선택할 수 있습니다. 이 항목은 "Intel C-State" 기능이 활성화된 경우 나타납니다. [Auto] 이 설정은 BIOS에서 자동으로 구성됩니다. [C0~C7s] 절전 레벨을 낮아지는 순서로 배열하면 다음과 같습니다. C7s, C7, C6, C3, C2, C0.
BIOSの設定 CLICK BIOSはMSIにより開発し、マウスとキーボードでBIOSのパラメーターを設定 するために、パラメーターグラフィカルユーザーインターフェースを提供します。 CLICK BIOSで、ユーザーがBIOSの設定を変更し、CPUの温度を監視し、ブートデバ イス優先順序を選択し、およびCPUの名前、DRAM容量、OSバージョンとBIOSバー ジョンなどのシステムの情報を見ることができます。バックアップ、または他人と共 有するために、パラメーターデータをインポート/エクスポートすることもできます。 BIOSセットアップ画面の起動 電源を投入するとハードウェアの初期化が始まり、POST(Power On Self Test)画面が 現れます。以下のメッセージが表示されている間に、<DEL>キーを押してBIOSセッ トアップ画面を呼び出します。 Press DEL key to enter Setup Menu, F11 to enter Boot Menu (<DEL>キーを押してセットアップ画面を呼び出して、F11キーを押 してブート画面を呼び出す。) <DEL>を押す前にこのメッセジーが消えてしまった場合、電源をいったん切ってから 再び投入するか、<RESET>を押すかして、システムを再起動してください。<Ctrl>、 <Alt>と<Delete>を同時に押しても再起動できます。 MSIはさらにBIOSセットアップ画面を表示するための2つの方法を提供します。“MSI Fast Boot”ユーティリティ画面で “GO2BIOS”タブをクリックするか、マザーボード基 板上の”GO2BIOS”ボタン(オプション)を押すことで、再起動後のPC起動時にBIOSセ ットアップ画面が表示されます。 “MSI Fast Boot”ユーティ リティの”GO2BIOS”ボタ...
Page 122
▶ Adjust Ring Ratio [Auto] Ringの倍率を設定します。有効値の範囲は装着したCPUによって決定されます。 ▶ Adjusted Ring Frequency 変更したRingの周波数を表示します。読み取り専用です。 ▶ Adjust GT Ratio [Auto] 統合したグラフィックスの倍率を設定します。有効値の範囲は装着したCPUによって 決定されます。 ▶ Adjusted GT Frequency 変更した統合のグラフィックスの周波数を表示します。読み取り専用です。 ▶ DRAM Reference Clock [Auto] DRAM基準クロックを設定します。有効値の範囲は装着したCPUによって決定されま す。CPUがこの設定をサポートする場合にのみこの項目は表示されます。 ▶ DRAM Frequency [Auto] DRAM周波数を設定します。オーバークロックによる動作は保証されませんのでご注 意ください。 ▶ Adjusted DRAM Frequency 変更したDRAM周波数を表示します。読み取り専用です。...
Page 123
▶ DRAM Training Configuration <Enter>キーを押すと、サブメニューが表示されます。DRAMのそれぞれのトレーニ ング方法を有効か無効にします。メモリタイミングを変更した後、システムが不安定 になるあるいは起動できない恐れがあります。その場合には、CMOSデータをクリ アし、デフォルト設定に戻してください。(クリアCMOSジャンパ/ボタンの節を参照 し、それにBIOSの設定画面にデフォルト設定をロードしてください。) ▶ Memory Fast Boot [Auto] 起動時に実行されるメモリに対応したトレーニングプロセスについて有効か無効にし ます。 [Auto] BIOSにより自動的に設定を行います。 [Enabled] 初回起動時に実行したトレーニングのプロセスを記憶します。その後 は毎回の起動時にトレーニングしなくなるため、システムの起動時間 が早くなります。 [Disabled] 毎回の起動時にメモリトレーニングプロセスが開始されます。 ▶ DigitALL Power <Enter>キーを押すと、サブメニューが表示されます。CPU PWM関連のデジタルパ ワーをコントロールします。 ▶ CPU Phase Control [Auto] CPUの負荷に比例するPWMフェーズをコントロールします。”Auto”に設定する と、BIOSが自動的にCPU PWMフェーズを最適化します。 [Auto] BIOSにより自動的に設定を行います。 [Disabled] この機能を切り替えると、PWM電源フェーズを無効にします。...
Page 124
▶ CPU Switching Frequency [Auto] PWMの動作スピードを設定します。PWMの動作スピードを上げるとCPUコア電 圧が安定化し、リップルの範囲を最小にしますが、MOSFETはより高温になりま す。この数値を上げる場合は、事前に必ずMOSFETの冷却対策を実施してくださ い。”Auto”に設定すると、BIOSが自動的に行います。 ▶ CPU VRM Over Temperature Protection [Enabled] CPU VRMの過温度保護機能を有効か無効にします。 [Enabled] 過温度上昇保護のためにCPU VRMに温度限度を設定します。 [Disabled] 過温度保護機能を無効にします。保護機能が働かないためシステム に損害を与えるかもしれません。 ▶ Digital Compensation Level [Auto] MOSフェーズが変更されると、CPU PWMの電流補償レベルを設定します。 "Auto"に設定すると、BIOSが自動的に行います。より高い補償レベルに設定した 場合、オーバークロックの性能が強くなります。 ▶ Imon Overwrite [Auto] CPUのイモン電流を設定します。 [Auto] BIOSにより自動的に設定を行います。 [Quarter] イモン電流を4分の1に設定します。...
Page 125
▶ CPU Core Voltage/ CPU Ring Voltage/ CPU GT Voltage [Auto] 電圧を設定します。”Auto”に設定すると、BIOSが自動的に電圧を設定します。ユーザ ーが手動で設定することも出来ます。 ▶ CPU Core Voltage Offset Mode/ CPU Ring Voltage Offset Mode/ CPU GT Voltage Offset Mode/ CPU SA Voltage Offset Mode/ CPU IO Analog Voltage Offset Mode/ CPU IO Digital Voltage Offset Mode [Auto] 電圧のオフセットモードを選択します。...
Page 126
▶ CPU Memory Changed Detect [Enabled] CPUまたはメモリを交換した場合、ブート中に警告メッセージを出力するシステムを 有効か無効にします。 [Enabled] システムがブート中に警告メッセージを発し、新しいデバイス対応の デフォルト設定をロードします。 [Disabled] この機能を無効にし、現在のBIOS設定を保持します。 ▶ CPU Specifications <Enter>キーを押すと、サブメニューが表示されます。サブメニューには装着した CPUの設定を全部表示します。[F4]を押すと、いつでもこの情報メニューをアクセス できます。読み取り専用です。 ▶ CPU Technology Support <Enter>キーを押すと、サブメニューが表示されます。装着されたCPUのサポート するテクノロジを示します。読み取り専用です。 ▶ MEMORY-Z <Enter>キーを押すと、サブメニューが表示されます。サブメニューには装着したメ モリの設定やタイミングを全部表示します。[F5]を押すと、いつでもこの情報メニュ ーをアクセスできます。 ▶ DIMM1~4 Memory SPD <Enter>キーを押すと、サブメニューが表示されます。装着されたメモリの情報を 示します。読み取り専用です。 ▶ CPU Features <Enter>キーを押すと、サブメニューが表示されます。 ▶...
背板快速指南 PS/2 鍵盤/ 滑鼠 網路連接埠 VGA 連接埠 USB 2.0 連接埠 複合連接埠 USB 2.0 音效輸入 RS-輸出 連接埠 音效輸出 CS-輸出 HDMI 連接埠 USB 3.0 連接埠 麥克風 SS-輸出 USB 2.0 連接埠 DVI-D 連接埠 ▶ PS/2 鍵盤 / 滑鼠複合連接埠 複合 PS/2 滑鼠/鍵盤的 DIN 接頭,可接 PS/2 滑鼠/鍵盤。...
Page 136
▶ USB 3.0 連接埠 USB 3.0 連接埠向下相容 USB 2.0 裝置,最高支援每秒 5 Gbit 的傳輸速率 (SuperSpeed)。 注意事項 要使用 USB 3.0 裝置,務必接到電腦的 USB 3.0 連接埠。請使用符合 USB 3.0 規格的 USB 連接線。 ▶ 網路連接埠 標準 RJ-45 插座,可連上區域網路。 LED 狀態 說明 未連線 Link/ Activity LED 黃燈 已連線...
CPU (中央處理器) LGA 1150 CPU 簡介 LGA 1150 CPU 表面有 2 處凹槽及 1 處黃色三角標記,協助您在整個主機板配置 中能正確擺放 CPU。黃色三角標記為腳位 1 位置。 凹槽 凹槽 黃色三角標記為腳位 1 位置 注意事項 溫度過高 溫度過高會嚴重損壞 CPU 以及主機板。務必確認散熱風扇正常運作,以免 CPU 過 熱。並於 CPU 與散熱器間均勻塗抹散熱膏 (或貼上散熱膠帶) 加強散熱。 更換 CPU 更換 CPU 時,為保險起見,應先關機後再拔掉電源線,以免損壞 CPU。 超頻...
Page 138
安裝中央處理器與散熱風扇 在安裝 CPU 時,記得要裝上 CPU 散熱風扇,避免過熱以維持系統穩定。請依下列步 驟,正確安裝 CPU 與 CPU 散熱風扇。不當的安裝可能會使 CPU 與主機板受損。 示範影片 請進入以下連結,觀賞正確安裝 CPU & 風扇的方法。 http://youtu.be/bf5La099urI 1. 鬆開拉桿到全開的位置。 2. 鬆開拉桿的同時,上蓋會順勢往上全開。 拉桿 上蓋 固定片 注意事項 請勿觸摸 CPU 插座針腳或 CPU 底部。 Tc-10...
Page 139
3. 將凹槽對準插座對齊點,將 CPU 往下平放,檢查 CPU 是否已安裝好在插座上。 4. 將拉桿下壓扣住。 CPU 凹槽 對齊點 固定旋鈕 5. 壓下拉桿,PnP 上蓋會自動從 CPU 插座鬆開,請勿丟棄 PnP 上蓋,若插座未放置 CPU,請務必用 PnP 上蓋保護插座針腳。 6. 在 CPU 上方均勻塗抹一層厚的散熱膏 (或貼上散熱膠帶) 有助 CPU 散熱。 PnP 上蓋 散熱膏 Tc-11...
Page 140
7. 找到主機板上的 CPU 風扇接頭。 8. 將散熱風扇放上主機板,將風扇排線往風扇接頭方向放,扣件對準主機板上的孔 位。 CPU 風扇接頭 9. 將散熱風扇向下壓穩,再將 4 個扣件往下壓固定散熱風扇。固定好會聽到喀嚓聲。 10. 檢查主機板確認扣件均已固定好。 11. 最後將 CPU 風扇排線接到主機板上的 CPU 風扇接頭後即告完成。 主機板 扣件底端 注意事項 • 確認 CPU 散熱風扇已與 CPU 黏緊後再開機。 • 未安裝 CPU 時,請用塑膠蓋保護 CPU 插座以免受損。 若另行購買 CPU 散熱風扇,請參閱該包裝內安裝細節。 • Tc-12...
BIOS 設定 CLICK BIOS 是由 MSI 團隊所研發的圖形使用者介面,支援以滑鼠及鍵盤來設定 BIOS 參數。 透過功能強大的 CLICK BIOS,可調整 BIOS 設定、檢視 CPU 名稱、記憶體容量及 BIOS 版本等系統訊息,或是監控 CPU 溫度、選取開機裝置順序等。您還可將參數輸 入及輸出、製作備份或與友人分享設定數值。且在連上網路後,就能瀏覽網頁、收發信 並即時更新系統。 進入 開機後,系統就會開始 POST (開機自我測試) 程序。當下列訊息出現在螢幕上時,請按 <DEL> 鍵,進入設定程式。 Press DEL key to enter Setup Menu, F11 to enter Boot Menu (按...
Page 158
定性。本項需 CPU 支援本功能才會顯示。 ▶ Current CPU Base Clock Strap (Z87-G43 GAMING) 本項顯示目前 CPU 基頻 Strap。唯讀。本項需 CPU 支援本功能才能變更。 ▶ Adjust CPU Base Clock Strap [Auto] (Z87-G43 GAMING) 本項設定 CPU 基頻 strap,您可調整本數值超頻 CPU。請注意我們無法保證超頻動作 及其穩定性。本項需 CPU 支援本功能才能變更。設為自動 (Auto), BIOS 會自動設 定。[選項:Auto, 1.00, 1.25, 1.67] ▶...
Page 159
▶ CPU PCIE PLL [Auto] (Z87-G43 GAMING) 選擇 CPU PCIe 的鎖相迴路 (PLL) 模式。本項需 CPU 支援本功能才會顯示。 [Auto] 本項由 BIOS 自動設定 [LC PLL] 開啟 LC PLL 一般使用 [SB PLL] 開啟 SB PLL 極限超頻 ▶ Filter PLL [Auto] (Z87-G43 GAMING) 本項開啟或關閉 CPU PLL 濾波器功能。本項需 CPU 支援本功能才會顯示。...
Page 161
▶ CPU Over Current Protection [Auto] 本項設定 CPU 過電流保護限值。設為自動 (Auto),BIOS 會自動設定。較高比例表 示較少保護,可能會損壞系統。 ▶ Phase Over Current Protection [Enabled] 本項開啟或關閉相位過電流保護。 [Enabled] 設定相位過電流保護限值 [Disabled] 關閉本功能 ▶ CPU Switching Frequency [Auto] 本項設定 PWM 工作速度以穩定 CPU 核心電壓,減少濾波限值。PWM 工作數值越 高,MOSFET 溫度將隨之升高,因此在增加頻率前,請務必確認已備好降溫的解決 方案。設為自動 (Auto),BIOS 會自動設定。 ▶ CPU VRM Over Temperature Protection [Enabled] 本項開啟或關閉...
Page 162
▶ CPU Core Voltage/ CPU Ring Voltage/ CPU GT Voltage [Auto] 本項設定上述電壓。設為自動 (Auto),BIOS 會自動設定,或者您也可改成手動設定。 ▶ CPU Core Voltage Offset Mode/ CPU Ring Voltage Offset Mode/ CPU GT Voltage Offset Mode/ CPU SA Voltage Offset Mode/ CPU IO Analog Voltage Offset Mode/ CPU IO Digital Voltage Offset Mode [Auto] Selects the voltage offset modes.
Page 163
▶ CPU Technology Support 按下 <Enter> 鍵以進入子選單。子選單顯示已安裝 CPU 所支援的技術。唯讀。 ▶ MEMORY-Z 按下 <Enter> 鍵以進入子選單。子選單顯示已安裝記憶體所有設定及時序。請按 [F5] 隨時進入查看本訊息。 ▶ DIMM1~4 Memory SPD 按下 <Enter> 鍵以進入子選單。本選單顯示已安裝記憶體訊息。唯讀。 ▶ CPU Features 按下 <Enter> 鍵以進入子選單。 ▶ Hyper-Threading Technology [Enabled] 導入 Hyper-Threading 技術的處理器,可增進傳輸速率及減少使用者的反應時間。 此技術是將處理器內的雙核心視為兩顆可同時執行指令的邏輯處理器。這樣一來, 系統效能即可大幅提升。 [Enable] 啟用 Intel Hyper-Threading技術 [Disabled] 如作業系統不支援...
Page 164
▶ CPU AES Instructions [Enabled] 本項開啟或關閉 CPU AES (進階加密標準) 功能 。本項需 CPU 支援本功能才會顯 示。 [Enabled] 開啟 Intel AES 功能 [Disabled] 關閉 Intel AES 功能 ▶ Intel Adaptive Thermal Monitor [Enabled] 本項開啟或關閉 Intel 適應熱度監控功能,以避免 CPU 過熱。 [Enabled] CPU 過熱會調整 CPU 核心時脈速度 [Disabled] 關閉本功能...
后置面板 PS/2 键盘/鼠 LAN 端口 USB 2.0 端口 标组合端口 Line-In RS-Out USB 2.0 端口 Line-Out CS-Out SS-Out USB 2.0 端口 HDMI DVI-D 端口 USB 3.0 端口 ▶ PS/2 键盘/鼠标组合端口 组合 PS/2 鼠标/键盘迷你 DIN 接口。可连接 PS/2 鼠标/键盘。 ® ® ▶ VGA 端口 此...
Page 172
▶ USB 3.0 端口 USB 3.0端口向下兼容USB 2.0设备。它支持高达5 Gbit/s(超高速)的数据传输速率。 注意 为了使用 USB 3.0 设备您必须连接到 USB 3.0 端口上。如果使用 USB 连接线必须要与 USB 3.0 兼容。 ▶ LAN 端口 标准的 RJ-45 插座,可连接局域网。 LED 状态 描述 关 网络未连接 Link/ Activity LED 黄色 网路已连接 LINK/ACT SPEED (连线/工作灯号) 闪烁...
Page 194
Current CPU/ DRAM/ Ring Frequency 此项用来显示当前已安装的 CPU,内存和 Ring。只读。 ▶ CPU Base Clock (MHz) [Default] 此项允许您设置CPU主频。您可以通过调整数值来对CPU进行超频。请注意我们无法保 证超频动作。当已安装的处理器支持此功能时此项显示。 ▶ Current CPU Base Clock Strap (Z87-G43 GAMING) 显示当前CPU基准时钟带。只读。当处理器支持此功能时此项才显示。 ▶ Adjust CPU Base Clock Strap [Auto] (Z87-G43 GAMING) 设置CPU基准时钟带。您可以通过调整此值来对CPU基准时钟超频。我们无法保证超频 动作。只有在CPU支持此功能时,此选项才能更改。如果设置为"Auto",BIOS将自动 配置此设置。 [选项: Auto, 1.00, 1.25, 1.67] Sc-30...
Page 196
▶ Adjust Ring Ratio [Auto] 设置 ring ratio 选项。有效值范围取决于已安装的CPU。 ▶ Adjusted Ring Frequency 显示已经调整的 Ring 频率。只读。 ▶ Adjust GT Ratio [Auto] 设置板载显卡比率。有效值范围取决于已安装的CPU。 ▶ Adjusted GT Frequency 显示已调整的板载显卡频率。只读。 ▶ DRAM Reference Clock [Auto] 设置 DRAM reference clock 选项。有效值范围取决于已安装的CPU。当支持此调整的 CPU安装时此项出现。 ▶ DRAM Frequency [Auto] 设置内存频率选项。请注意我们无法保证超频动作。...
Page 197
▶ Memory Fast Boot [Auto] 开启或关闭内存每次开机时的初始化和自我检测。 [Auto] 此设置由BIOS自动配置。 [Enabled] 内存模块将完全模仿第一次开机的初始化和自检配置。当第一次开机 后,内存不再需要初始化和自检,以便加快系统开机速度。 [Disabled] 每次启动内存模块都会初始化并自检。 ▶ DigitALL Power 按<Enter>进入子菜单。控制与CPU PWM 相关联的数字供电。 ▶ CPU Phase Control [Auto] 根据CPU负载适当的控制 PWM 相位。如果设置为"Auto",BIOS将自动地优化 CPU PWM 相位。 [Auto] 此设置由BIOS自动配置。 [Disabled] 关闭 PWM 电源相位切换功能。 ▶ CPU Vdroop Offset Control [Auto] 设置CPU电压下降偏移百分比。如果设置为...
Page 198
▶ CPU VRM Over Temperature Protection [Enabled] 开启或关闭 CPU VRM 超温度保护。 [Enabled] 设置CPU VRM超温度保护极限值。 [Disabled] 关闭此功能。 ▶ Digital Compensation Level [Auto] 当 MOS 相位改变时为 CPU PWM 设置数字供电电流补偿,如果设置为"Auto", BIOS 将自动配置此设置。提供越高的电流补偿将获得越高的超频能力。 ▶ Imon Overwrite [Auto] 为 CPU 设置 Imon 电流。 [Auto] 此项由BIOS自动配置。 [Quarter] 设置...
Page 199
▶ CPU Core Voltage Offset Mode/ CPU Ring Voltage Offset Mode/ CPU GT Voltage Offset Mode/ CPU SA Voltage Offset Mode/ CPU IO Analog Voltage Offset Mode/ CPU IO Digital Voltage Offset Mode [Auto] 选择电压偏移模式。 [Auto] 此设置由BIOS自动配置。 允许您设置偏移电压的正值。 允许您设置偏移电压的负值。 ▶ CPU Core Voltage Offset/ CPU Ring Voltage Offset/ CPU GT Voltage Offset/ CPU SA Voltage Offset/ CPU IO Analog Voltage Offset/ CPU IO Digital Voltage Offset [Auto] 为这些电压设置偏移值。...
Page 200
▶ CPU Specifications 按<Enter>进入子菜单。此子菜单高亮显示您CPU所有键的属性。您也可以通过按 [F4]在任何时间访问此信息。只读。 ▶ CPU Technology Support 按<Enter>进入子菜单。此子菜单显示已安装CPU支持的键功能。只读。 ▶ MEMORY-Z 按<Enter>进入子菜单。此子菜单显示所有设置和已安装内存时序。您也可以任何时间 通过长按 [F5] 来访问此信息。 ▶ DIMM1~4 Memory SPD 按<Enter>进入子菜单,此子菜单显示已安装内存信息。只读。 ▶ CPU Features 按<Enter>进入子菜单。 ▶ Hyper-Threading Technology [Enabled] 处理器使用超线程技术增加处理事务效率,减少终端用户响应时间。这个技术把在 处理器内部的两个内核当做两个可以同时执行指令的逻辑处理器。用这种方法,系 统性能得到了极大的提高。 [Enable] 开启 Intel Hyper-Threading 技术。 [Disabled] 如果操作系统不支持 HT 功能关闭此项。 ▶...
Page 202
▶ LakeTiny Feature [Disabled] (optional) 为固态硬盘(SSD)开启或关闭iRST的Intel Lack Tiny功能。当安装的CPU支持此功 能并且“Intel C-State”开启时此项出现。 [Enabled] 加强动态IO负载调节性能,加快固态硬盘速度。 [Disabled] 关闭此功能。 注意: 当 "Intel Turbo Boost " 开启时,下列选项出现. ▶ Long Duration Power Limit (W) [Auto] 为CPU Turbo Boost 模式设置长时间TDP功率限制。 ▶ Long Duration Maintained (s) [Auto] 为 "Long duration power Limit(W)" 设置长时间TDP维持时间。 ▶...
Page 203
Installation/ 설치하기/ インストール/ 安裝/ 安装 This chapter provides demonstration diagrams about how to install your computer. Some of the installations also provide video demonstrations. Please link to the URL to watch it with the web browser on your phone or tablet.