Table of contents 1 Introduction Congratulations on your purchase and welcome Introduction to Philips AVENT! To fully benefit from the support that Philips AVENT offers, register your General description product at www.philips.com/welcome. The Philips AVENT video monitor provides you Preparing for use...
II Baby unit 3.1.2 Placing the non-rechargeable batteries Antenna in case of a power failure, the baby unit can run Power-on light on four 1.5V R6 AAA alkaline batteries (not included). Microphone Do not use rechargeable batteries. The baby Lens unit does not have a charging function and Loudspeaker rechargeable batteries discharge slowly when...
Reattach the lid. Slide down the battery compartment lid to remove it. 3.2 Parent unit insert the rechargeable battery. 3.2.1 Operation on rechargeable battery Warning: Unplug the parent unit and make sure your hands and the unit are dry when you insert the rechargeable battery.
insert the appliance plug into the parent unit Note: • and insert the adapter into an electrical outlet. When the parent unit is charged for the first time, the operating time is less than 7 hours. The rechargeable battery only reaches its full capacity after four discharging and charging cycles.
Note: Tip: The power-on light always lights up green, Find out what the best position is for even when there is no connection with the parent unit by looking at the signal the parent unit. strength symbol. The number of stripes indicates the quality of the connection.
Page 8
There are two ways to position the baby unit: Place the parent unit within the operating Place the baby unit on a stable, level and range of the baby unit. Make sure it is at least horizontal surface. 1.5 meters (5 feet) away from the baby unit Mount the baby unit to the wall as shown to avoid acoustic feedback.
5.2 Adjusting display brightness 5 Features You can adjust the display brightness of the parent unit to the level you prefer. 5.1 Adjusting loudspeaker Press the brightness adjustment buttons on volume the parent unit to adjust the brightness of the You can adjust the loudspeaker volume of the video display.
5.3 Sound level lights • The voice activation light on the parent The parent unit continuously monitors the sound unit goes on and the voice activation level in your baby’s room and the sound level image appears on the video display. lights let you know if there is any activity.
• The nightlight on the base of the baby To select another lullaby, press the lullaby unit goes on. button. Continue pressing the ‘next lullaby’ button until you hear the lullaby you prefer. Press the nightlight button again to turn off the nightlight.
5.7 Out-of-range alert 5.10 Auto mute feature When the parent unit is out of range of the baby When the baby unit detects a low sound level, unit, the parent unit beeps every 20 seconds and the e.g. the sleeping sound of the baby, the parent unit out-of-range image appears on the video display.
To purchase accessories for this appliance, please visit our online shop at www.shop.philips.com/ service. if the online shop is not available in your country, go to your Philips dealer or a Philips Warning: Do not immerse the parent unit and the baby service centre.
If you cannot find the Why can’t I establish a connection? answer to your question, visit www.philips.com/ Why is the connection lost every now and then? support for more frequently asked questions or Why are there sound interruptions? contact the Consumer Care Center in your country.
Page 15
Why do the non-rechargeable batteries of the Why does the parent unit beep? baby unit run low quickly? • if the parent unit beeps while the out-of- • The baby unit consumes a lot of energy range image appears on the video display, the when you have the video display turned on connection with the baby unit is lost.
Page 16
• Perhaps the baby monitor is in auto mute. Operating time/operating range When the baby unit detects a low sound level, e.g. the sleeping sound of the baby, the parent The specified operating range of the baby monitor unit automatically mutes the sound output so is up to 150 meters (490 feet) outdoors and up to 30 meters (98 feet) indoors.
Page 17
Output video display Why does the video display flicker? • interference may occur when the parent unit is out of range of the baby unit. interference may also occur if there are too many walls or ceilings between the parent unit and the baby unit or when other 2.4ghz wireless devices are turned on (e.g.