All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by WO 0264 Service PaCE...
EN 2 EM5E Technical Specifications, Connections and Chassis Overview 1. Technical Specifications, Connections and Chassis Overview Technical Specifications 1.2.2 Rear Connections 1.1.1 Vision Display type : CRT, Real Flat WS Screen size : 28” (70 cm) : 32" (82 cm) : 36”...
Page 3
Technical Specifications, Connections and Chassis Overview EM5E EN 3 External 2: CVBS and SVHS - In (for VCR) RJ45: Wireless Surround Transmitter - Out 1 - SDA2_TM Signal 2 - SCL2_TM Signal 3 - GND Ground 4 - I C_MUTE Signal 5 - 15V Supply...
Page 4
EN 4 EM5E Technical Specifications, Connections and Chassis Overview Chassis Overview TOP CONTROL PANEL CRT PANEL SIDE I/O PANEL SMALL SIGNAL BOARD MAINSWITCH PANEL AUTO-SCAVEM LARGE SIGNAL PANEL DC-SHIFT I/O 3rd SCART (optional) DAF PANEL CL 26532041_072.eps 220402 Figure 1-6 PWB location...
Safety and Maintenance Instructions, Warnings, and Notes EM5E EN 5 2. Safety and Maintenance Instructions, Warnings, and Notes Safety Instructions Warnings Safety regulations require that during a repair: • In order to prevent damage to ICs and transistors, avoid all •...
Page 6
EN 6 EM5E Safety and Maintenance Instructions, Warnings, and Notes • The semiconductors indicated in the circuit diagram and in the parts lists, are interchangeable per position with the semiconductors in the unit, irrespective of the type indication on these semiconductors. •...
Mechanical Instructions EM5E EN 21 4. Mechanical Instructions Index of this chapter: 4.2.3 Sub-woofer Removal 1. Service connector 2. Set Disassembly Caution: Do not disconnect the loudspeaker cable from the 3. Service Positions subwoofer box when the set is operative, because the class-D 4.
Page 22
EN 22 EM5E Mechanical Instructions 4.3.2 Component Side LSP To get access to the bottom side (solder side) of the LSP, do the following (see figure above): SSB top-bracket 1. Remove the DAF-module (see paragraph ‘DAF Assy/ panel’ below 2. To disconnect the degaussing coil from the LSP, remove AUTO-SCAVEM the cable from connector 1502 [1].
Page 23
Mechanical Instructions EM5E EN 23 Assy / Board Removal Sometimes, it can be necessary to swap a complete assy or Printed Wiring Board (PWB). How that can be done is explained below. 4.4.1 Top Control Assy/Panel S S B Top control board CL 16532149_068.eps 051201 Figure 4-8 Top control assy...
Page 24
EN 24 EM5E Mechanical Instructions Set Reassembly 1. Release the two fixation clamps (rather difficult to reach), by pushing them upwards [1]. At the same time, pull the To reassemble the whole set, do all processes in reverse order. complete assy backwards [2]. Note: be aware that the degaussing coil can hamper this.
Service Default Mode (SDM) and Service Alignment Mode (SAM) offer several features for the service technician, while 5.2.2 Service Alignment Mode (SAM) the Customer Service Mode (CSM) is used for communication between a Philips Customer Care Centre (P3C) and a customer. Purpose • To perform (software) alignments.
Page 26
This will give call his dealer. The service technician can than ask the the Philips Service department an extra possibility for customer to activate the CSM, in order to identify the status of diagnosis (e.g. when Development asks for this).
Page 27
Service Modes, Error Codes and Fault Finding EM5E EN 27 the buffer is empty ('000'). See also paragraph 5.5 for a • Digital Option. Gives the selected digital mode, '100 HZ', description. 'Digital Scan', 'Natural Motion', 'Double Lines', or 'Pixel •...
Page 28
7 is low (< 10) or the value of line 8 is low (< 10), 5.4.1 Introduction increase the 'Brightness' or the 'Contrast' value. ComPair (Computer Aided Repair) is a service tool for Philips Picture too bright Consumer Electronics products. ComPair is a further 1. Press 'Smart Picture' button on the RC-transmitter. In case...
Page 29
Service Modes, Error Codes and Fault Finding EM5E EN 29 • ComPair speeds up the repair time since it can Table 5-1 Stepwise start-up table automatically communicate with the chassis (when the microprocessor is working) and all repair information is State Description mode Display LED Enabled pro-...
EN 30 EM5E Service Modes, Error Codes and Fault Finding 7. Plug the mains adapter in a mains outlet, and switch the 5.5.3 How to clear the Error Buffer interface 'ON'. The green and red LEDs light up together. The red LED extinguishes after approx. 1 second while the Use one of the following methods: green LED remains lit.
Page 32
EN 32 EM5E Service Modes, Error Codes and Fault Finding • The Service Alignment Mode (SAM). In this mode, items initialised again, to ensure the normal picture and sound of the set can be adjusted via a menu and with the help of conditions of the set.
Service Modes, Error Codes and Fault Finding EM5E EN 33 diagram A6) will put the IC7700 in Standby mode (via tri- 3. Via the ‘SUP-ENABLE’ signal, the Main Supply is switched state input pin 6). For more details, see chapter 9. ‘on’...
Page 34
EN 34 EM5E Service Modes, Error Codes and Fault Finding (first connect ground to measuring equipment, than measure frame deflection, the beam current could damage the CRT the gate). neck, leading to a defective CRT. • Best thing to do is: 5.8.6 Standby Supply •...
Page 35
Service Modes, Error Codes and Fault Finding EM5E EN 35 Phenomenon Possible Cause Repair tip No sound at headphone HP amplifier (7681) on dia- Measure on pin 3 input left and pin 1 output left, repeat this for pin 3 (input right) and output.
Page 36
EN 36 EM5E Service Modes, Error Codes and Fault Finding Personal Notes:...
Page 97
Electrical Alignments EM5E EN 97 8. Electrical Alignments Index of this chapter 1. General alignment conditions 2. Hardware alignments 3. Software alignments 4. Option settings 1502 General Alignment Conditions 8.1.1 Start Conditions Warning All alignments Perform all electrical adjustments under the following are on hot-part ! conditions: 5430...
Page 98
Focus 2 (F2) = Dynamic alignment (red wire). Luma gain Fixed setting: 2. Focus method for Philips 32” tube with bleeder gun 1. Start the alignment with the STATIC focus (upper IF AFC potmeter) turned to the left and the DYNAMIC focus Supply, via an external video generator (e.g.
Electrical Alignments EM5E EN 99 Table 8-1 OSD feedback of AFC alignment Table 8-2 Cathode parameter AFC-window AFC-frequency vs. reference Light output (cd/m High 28" RF WS High 29" RF 4:3 32" RF WS 36" RF WS Table 8-3 White levels 1.
Page 100
EN 100 EM5E Electrical Alignments 8.3.5 Geo-Nor (Normal Geometry) 3. Connect a voltmeter (V ) between R3624 and 'hot' ground. 4. Adjust the DC voltage to '0' with potmeter R3642 (see Note: Use for all geometry alignments an external pattern figure 8-1).
Page 101
Set with Home Cinema Link (EU only) Set without Home Cinema Link Integrated RC Feature present. Feature not present. Tuner type Philips Set with Philips tuner. Alps Set with Alps tuner. 38.0 IF For AP PAL-multi set. For non AP PAL-multi sets Integrated DVD Feature present.
Page 102
16384 = On (EU) 15 Integrated RC 0 = Off 32768 = On (EU) China IF 0 = Off Sum OB4 4 = On Tuner 0 = Philips 8 = Alps 13 DVD-door lock 0 = Off 8192 = On...
Page 103
Electrical Alignments EM5E EN 103 Table 8-7 Option bytes Group 2 OB Bit Option name Settings(in decimal values) Auto Store Mode 0 = None (AP/USA) Sum OB5 2 = PDC/VPS 4 = TXT Page 6 = PDC/VPS/TXT Page Picture Mute 0 = Off 16 = On Virgin...
EN 104 EM5E Circuit Descriptions and Abbreviation List 9. Circuit Descriptions and Abbreviation List Index of this chapter 1. Introduction 2. Block diagram 3. Power supply 4. Control 5. Tuner & IF 6. Video: High-end Input Processor 7. Video: Feature box 8.
Page 105
Circuit Descriptions and Abbreviation List EM5E EN 105 Block Diagram UV13XX TDA932X SAA4978 TDA9178 TDA933X FRAMEDRIVE+ TUNER PICNIC TOPIC VERT FRAMEDRIVE- FILTER SYNC VIDEO D100 D100 HORZ AUDIO YUV_EAGLE SAA4992 T8F24EF FALCONIC EAGLE SCAVEM SAA5801 CVBS-TXT AUTO SYNC SCAVEM ( P) CNTRL KEYBRD RGB-TXT...
Page 106
EN 106 EM5E Circuit Descriptions and Abbreviation List Amplification is done via a 'class D' integrated power amplifier processor (OTC) is 'low', transistor 7528 will conduct and relay IC, the TDA7490. 1550 is activated. Initially a considerable current will flow, via PTC 3516, through the degaussing coil.
Page 107
Circuit Descriptions and Abbreviation List EM5E EN 107 = 0 V). The DC-voltage U will be transposed calculated such that they will block when above described MAINS across the primary winding of L5101 (3, 5), resulting in a situation occurs. In this case, the base of TS7708 is kept 'low' by the conducting TS7709, until the problem is solved.
Page 108
EN 108 EM5E Circuit Descriptions and Abbreviation List Protection A basic fly-back converter is used, with a MOSFET Q1, If the optocoupler would fail, the secondary voltage will transformer L1, and a primary feedback circuit. The output of increase. This would have disastrous consequences since the primary controlled voltage is U1.
Page 109
Circuit Descriptions and Abbreviation List EM5E EN 109 1. After closing switch 'S', the linear in time increasing current TS7502, and through that the T of the FET will decrease. The , will charge capacitor C. output voltage V will be reduced. 2.
Page 110
EN 110 EM5E Circuit Descriptions and Abbreviation List 9.4.1 Tuner & IF (Diagram A8 & B2) Introduction The tuner is I C controlled, and is capable of receiving off-air, The SAA5801 (IC7001) is called the OTC (OSD, TXT, and S- (cable) and Hyperband channels: Control).
Page 111
Peaking, again resulting in lines with extra picture Cinemalink (P50.3) information. Cinema Link is a new Philips feature in which the TV, the audio • The line frequency is fixed on 31250 Hz and the frame receiver, and other video peripherals like DVD player and video frequency at 75 Hz (this will give no frame-flicker).
Page 112
EN 112 EM5E Circuit Descriptions and Abbreviation List 9.7.2 Block diagram IC 7717 IC 7718 IC 7714 MEM 2 SAA4992 MS81V04160 MEM1 100Hz IC 7719 FALCONIC MEM 3 SCAN IC 7722 IC 7723 MEM 5 MEM 4 IC 7724 EAGLE YUV_EAGLE WE IE RE D...
Page 113
Dynamic Contrast. To make the contrast (black/white) 100Hz for YUV and HV-sync. In order to remove 'large area range wider, Philips has invented Dynamic Contrast. It flicker' (especially visible in a white picture), the field-rate of the uses the digital memory used in 100 Hz sets. It measures video is doubled by the FBX6.
Page 114
EN 114 EM5E Circuit Descriptions and Abbreviation List • LTI is amplitude dependent. This means that only 'big' jumps are processed. It works with a threshold, which is Amplitude 'ear' coupled to the noise meter via the Auto TV software. PEAKING •...
Page 115
Circuit Descriptions and Abbreviation List EM5E EN 115 cut-off voltage at a current of 8 µA. With this measurement, the Video: High-end Output Processor (HOP) and black level at the RGB-outputs is adjusted. Therefore, at start- TOPIC (diagram B4) up there is no monitor pulse anymore. At start-up, the HOP measures the pulses, which come back via pin 44.
Page 116
EN 116 EM5E Circuit Descriptions and Abbreviation List CRT and on the V from the HOP, for the synchronisation When no CVBS is offered to the video processor, the V SYNC of TXT/OSD/EPG pulses are switched 'off' by the HIP, and the pulses are generated by the PICNIC (to assure a stable OSD).
Page 117
Circuit Descriptions and Abbreviation List EM5E EN 117 during time interval t1-t3 the circuit resistance will be higher than during t4-t5. 5430 5430 I Defl Defl L5421 is called the linearity coil. To avoid self-oscillation, 141V 141V R3431 and C2431 are placed parallel to L5421. t2 t3 See also Figure 9-9 item '*1'.
Page 118
EN 118 EM5E Circuit Descriptions and Abbreviation List Beam-current Correction charge on C2622 this will give a flyback voltage of 32 V The 'EHT-info' signal at point 10 of the LOT depends on the (depending on the CRT size, this value can differ). value of the beam-current and the voltage from divider R3450, R3451, and C2450.
Circuit Descriptions and Abbreviation List EM5E EN 119 9.12 Audio (Diagram B6, A6 & A7) The following amplifier configurations are possible: • Virtual Dolby, L/R, 2 x 15 W (88XX-series and 8957-series with extra digital input). 9.12.1 Introduction • 3D Surround, L/R, Centre, Subwoofer, 4 x 15 W (95XX- series).
EN 120 EM5E Circuit Descriptions and Abbreviation List broadcast between e.g. news transmissions and commercials, or within a movie. To be able to get a Dolby approval (for the Virtual Dolby sets), the AVL feature must be switchable. Therefore, the AVL feature is customer switchable via the menu.
Circuit Descriptions and Abbreviation List EM5E EN 121 consist of sport, film, culture, etc. and are determined from 9.14.2 Rotation (Diagram A5) the station side. In sets with a rotation coil (wide screen sets), the amount of NexTView does not have to restrict itself to information about frame rotation is adjusted with the 'Tilt' DAC-output of the HOP the station that is being viewed, but also offers information pin 25 (see also 'Vertical Deflection').
Page 122
EN 122 EM5E Circuit Descriptions and Abbreviation List 9.15.3 Auto Scavem (Diagram SC) Coring/Clipping and Gain CORING / CLIPPING GAIN 11V8 Differen- Matrix Coring Clipper Gain tiator 11V8 7018 BFS20 11V8 Parabola Output 2012 BF824 7026 DAC6 7014 BFS20 modulation stage SVM coil 7022...
Page 123
Circuit Descriptions and Abbreviation List EM5E EN 123 Parabola Modulation and Pre-amplifier 9.16 Software Related Features PARABOLA MODULATION PRE-AMP Following features are described: +12S • Auto TV 11V8 • 'Switch On' Behaviour 7038 BFS20 10V9 10V9 SC10 10V1 7028 7032 BFS20 BFS20 9.16.1 AutoTV...
Page 124
EN 124 EM5E Circuit Descriptions and Abbreviation List 8. During start-up of the deflection, I C traffic must be Direction For Use: description for the disabled for 250 ms to avoid data corruption. If flashes or end user spikes are generated during EHT start-up, I C data could Digital Noise Reduction: noise be disturbed or corrupted.
Page 125
Circuit Descriptions and Abbreviation List EM5E EN 125 Intermediate Main supply for deflection (mostly 141 Input/Output Last Status The settings last chosen by the Vertical Drive 2fh: vertical sync pulse D100 customer and read and stored in RAM from deflection or in the NVM.