Cleaning Upholstery; Maintenance; Headlight Replacement - Hoover SpinScrub Owner's Manual

Hoover deep cleaner owner's manual spinscrub
Hide thumbs Also See for SpinScrub:
Table of Contents

Advertisement

3-16
A
B
9. Lift tool, and position it against riser.
Pull tool slowly over carpet without
pressing trigger (dry stroke).
It is best to alternate wet and dry strokes
as described above. End with more dry
strokes and watch for the green 'MAX
Extract' light to come on to aid in faster
drying of carpet.
10. Overlap strokes by 1/2 inch to help
prevent streaking.
To avoid saturating carpet, do not use
more than 4 wet strokes over any one
area. Always end with dry strokes.
If additional cleaning is necessary, wait
until the carpet is completely dry before
using the tool again.
11. Empty recovery tank when the red
'MAX Extract' light comes on and the
motor sound becomes higher pitched
and there is a loss in suction (see
"Automatic shut-off", Fig. 2-7).
When finished cleaning, follow "After
cleaning" instructions on page 9 and
"After using tool" instructions on page 12.
3-18
Make no more than 2 passes with the
solution over any one area to prevent
over-wetting and damage to fabric.
If additional cleaning is necessary, wait
until the upholstery is completely dry
before using the tool again.
11. Empty recovery tank when the red
'MAX Extract' light comes on and the
motor sound becomes higher pitched
and there is a loss in suction (see
"Automatic shut-off", Fig. 2-7).
When finished cleaning, follow "After
cleaning" instructions on page 9 and
"After using tool" instructions on page 12.

Cleaning upholstery

Read "Before you begin cleaning"
instructions on page 9.
Be sure to check the cleaning code on
your upholstery. Use your deep cleaner
only on upholstery marked "W"or
"W/S".
1. Place handle in upright position.
Agitator brushes will not rotate while
handle is in upright position.
2. Fill clean solution tank with HOOVER
Carpet/Upholstery Detergent according
to instructions for Figs. 2-9 to 2-15.
3. Attach tool to end of hose.
Do not point tools toward people or
pets.
4. Dry hands and plug deep cleaner into
a properly grounded outlet.
5. Turn deep cleaner ON. If necessary,
refer to "Before using tool" section to
remove air from the system.
6. Gently press the tool onto the fabric.
Press the trigger and slowly pull the noz-
zle over the fabric.
7. Overlap strokes by 1/2 inch to help
prevent streaking.

4. Maintenance

H e a d l i g h t
re p l a c e m e n t
What to buy
The deep cleaner uses a 7 volt, wedge
base type bulb, H O OVER part no.
2 7 3 1 3 1 0 6 .
W h e re to buy
Bulbs may be purchased from authorized
Hoover dealers (Depot), Hoover Factory
S e rvice Centers, or through The Hoover
Company online at www. h o o v e r. c o m .
3-17
Make additional strokes without pressing
the trigger to remove more moisture.
Also, periodically checking the 'MAX
Extract' lights will help ensure that the
maximum amount of water has been
removed.
8. To clean in corners or creases, lift the
tool one-half inch from the fabric and
press the solution trigger. The crevice
tool is very useful for this task.
9. Vacuum up the solution with the tool
without pressing the trigger.
10. For heavily soiled areas, it may be
necessary to repeat the cleaning
process. Make crisscrossing strokes to
the original pattern; overlap each pass.
4-1
How to re p l a c e
Turn cleaner off and with dry hands,
disconnect deep cleaner from electri-
cal outlet.
1. Using a Phillips scre w d r i v e r, re m o v e
the screw as shown and lift off lens.
Continued
13

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents