Related Manuals for Zenoah EHT602D
Summary of Contents for Zenoah EHT602D
- Page 1 OWNER’S MANUAL eHT752S eHT602D eHT752S / eHT602D 848D3M93A1 (712) HEDGE TRIMMER GB-1...
- Page 2 / eHT602D EXPLANATION OF SYMBOLS AND SAFETY WARNINGS eHT752S eHT602D MODEL eHT752S 21.7 cm eHT602D 21.7 cm APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION GB-2 WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection.
-
Page 3: Table Of Contents
NOTE This mark indicates hints or directions useful in the use of the product. EC DECLARATION OF CONFORMITY Husqvarna Zenoah Co., Ltd. 1-9, Minamidai, Kawagoe, Saitama, Japan DIRECTIVE 89/336/EEC, 98/37/EC 2000/14/EC Internal control production. : HEDGE TRIMMER... -
Page 4: Parts Location
12. Plate receive 2. Specification Model ... eHT752S / eHT602D Type ... double-action type eHT752S / eHT602D ... Single blade / Double blade Blade length (from the tip of Gear Case) eHT752S / eHT602D ... 670 / 530 mm Engine Model ... -
Page 5: Warning Labels On The Machine
Position: AIR CLEANER COVER The direction to open the choke Position: AIR CLEANER COVER eHT752S / eHT602D If warning label peels off or becomes soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s). -
Page 6: For Safe Operation
/ eHT602D 5. For safe operation 1. THIS MACHINE CAN CAUSE SERIOUS INJURIES. Read this manual carefully until you com- pletely understand and follow all safety and operating instruc- tions. Also, know how to stop the machine quickly in an emer- gency. - Page 7 / eHT602D WARNING • Never place the throttle into the high-speed position when start- ing the engine.
- Page 8 GB-8 HANDLING FUEL 1. The engine of the ZENOAH prod- uct is designed to run on a mixed fuel, which contains highly flam- mable gasoline. Never store cans of fuel or refill the tank of the unit...
-
Page 9: Fuel
• The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use (JASO FC GRADE OIL or ISO EGC GRADE). -
Page 10: Operation
/ eHT602D 7. Operation STARTING ENGINE WARNING The cutting head will start moving upon the engine starts. 1. Feed fuel into the fuel tank and tighten the cap se- curely. 2. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start moving upon starting of the engine. - Page 11 Vertical cut: • With the single-sided blade hedge-trimmer, model eHT752S always cut from the bottom up. • With the 2-sided blade model eHT602D use an arc- ing cut from the bottom upwards, then downwards to use both sides of the blades.
-
Page 12: Maintenance
/ eHT602D 8. Maintenance System/components fuel leaks, fuel spillage fuel tank, air filter, fuel filter idle adjusting screw spark plug cylinder fins, intake air cooling vent muffler, spark arrester, cylinder exhaust port throttle lever, ignition switch cutting parts gear case... - Page 13 . • [eHT752S] Check periodically if the rubber cushions are not deformed or damaged. • [eHT602D] Check periodically if the springs are not deformed or damaged. AIR FILTER • The air filter, if clogged, will reduce the engine perfor- mance.
- Page 14 / eHT602D 8. Maintenance WAY OF THE COOLING AIR • This engine is air-cooled. Dust clogging between the inlet port of the cooling air and cylinder fins will cause overheating of the engine. Periodically check and clean the cylinder fins after removing the air cleaner and the cylinder cover.
-
Page 15: Storage
10. Disposal When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations. eHT752S / eHT602D GB-15... -
Page 16: Troubleshooting Guide
(exhaust port) → carbon is built-up air cleaner cylinder fin, fan cover When your unit seems to need further service, please consult with our ZENOAH service shop in your area. Limited warranty Should any failure occur on the product under normal...