Advertisement
INSTRUCTION MANUAL
IMPORTANT INFORMATION
: Please read these instructions carefully and make
GB
sure you understand them before using this unit. Retain these instructions for future
reference.
MANUEL D'INSTRUCTIONS
RENSEIGNEMENTS IMPORTANTS:
Avant d'utiliser cet appareil, veuillez lire
FR
atentivement les instructions et assurez- -vous de les avoir comprises. Conservez
les instructions pour référence ultérieure.
BETRIEBSANWEISUNG
WICHTIGE INFORMATION:
Lesen Sie diese Hinweise zur Handhabung des
DE
Geräts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, daß Sie
alle Anweisungen verstanden haben und gut aufbewahren.
MANUAL DE INSTRUCCIONES
INFORMACIÓN IMPORTANTE:
ES
Lea atentamente las instrucciones y
asegúrese de entenderlas antes de utilizar esta aparato. Conserve las instruc-
ciones para la referencia en el futuro.
115306026 Rev. 3
11/15/10 BRW
Advertisement
Related Manuals for McCulloch Cabrio 115306026
Summary of Contents for McCulloch Cabrio 115306026
- Page 1 INSTRUCTION MANUAL IMPORTANT INFORMATION : Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference. MANUEL D’INSTRUCTIONS RENSEIGNEMENTS IMPORTANTS: Avant d’utiliser cet appareil, veuillez lire atentivement les instructions et assurez- -vous de les avoir comprises. Conservez les instructions pour référence ultérieure.
-
Page 2: Table Of Contents
TABLE OF CONTENTS Identification (What is What?) Identification of Symbols Safety Rules Assembly Operation Maintenance IDENTIFICATION (WHAT IS WHAT?) 1. Fuel tank 13. Throttle trigger 2. Loop handle 14. Throttle lock- -out 3. ON/STOP switch 15. Starter handle 4. Shoulder strap clamp 16. - Page 3 IDENTIFICATION OF SYMBOLS WARNING! This brushcutter can be dangerous! Careless or improper use can cause serious or even fatal injury. B. Read and understand the instruction manual before using the brushcutter. C. Always use: Ear protection, eye protection, head protection, boots, and gloves. DANGER! Blade can thrust violently away from material it does not cut.
- Page 4 S Maintain unit according to recommended procedures. Keep blade sharp. Keep cut- ting line at the proper length. S Use only 2,4 mm diameter McCulloch brand replacement line. Never use wire, rope, string, etc. S Install required shield properly before using the unit.
-
Page 5: Fuel Tank
S Keep others away when making carbure- tor adjustments. S Use only recommended McCulloch accesso- ries and replacement parts. S Have all maintenance and service not ex- plained in this manual performed by your au- thorized service dealer. FUEL SAFETY S Mix and pour fuel outdoors. -
Page 6: Shoulder Strap
INSTALLING TRIMMER ATTACHMENT WARNING: When installing attach- ment, place the unit on a flat surface for stabil- ity. 1. Loosen the coupler by turning the knob counterclockwise. Coupler Shipping protector LOOSEN Knob TIGHTEN 2. Remove shipping protector from coupler. 3. Remove the shaft cap from the attachment (if present). -
Page 7: Trimmer Head
5. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the hook is to the right side of your waist. NOTE: A one-half twist is built in the shoul- der strap to allow the strap to rest flat on the shoulder. -
Page 8: Shield
Do not use any blades, or fastening hardware other than the washers and nuts shown in the following illustrations. These parts must be provided by McCulloch and installed as shown below. Failure to use proper parts can cause the blade to fly off and seriously hurt you or others. - Page 9 10. Turn blade by hand. If the blade binds against the shield, or appears to be uneven, the blade is not centered, and you must re- install. NOTE: To remove blade, insert screwdriver into aligned holes. Unthread the nut and remove parts.
-
Page 10: Coupler
1. Set unit on a flat surface. 2. Slowly press the primer bulb 6 times. 3. Move the start lever to the START position. 4. Pull starter rope handle sharply until en- gine starts and runs. 5. Allow unit to run for 10- -15 seconds, then fully squeeze the throttle trigger to disen- gage the starting system. - Page 11 S Wear eye protection and heavy clothing. S Extend your left arm and hold loop handle with your left hand. S Hold throttle grip with your right hand with finger on throttle trigger. S Keep unit below waist level. S Keep shoulder strap pad centered on your left shoulder.
- Page 12 Mowing SWEEPING - - The fanning action of the rotat- ing line can be used to blow away loose debris from an area. Keep the line parallel to and above the area surface and swing the tool from side to side. Sweeping OPERATING INSTRUCTIONS FOR USE WITH WEED BLADE...
- Page 13 ADDITIONAL SAFETY RULES FOR OPTIONAL ATTACHMENTS WARNING: For each optional attach- ment used, read entire instruction manual be- fore use and follow all warnings and in- structions in manual and on attachment. WARNING: Ensure handlebar is installed when using edger or brushcutter at- tachments.
- Page 14 S Never operate the cultivator without the tine cover in place and properly secured. S Keep the tines and guard clear of debris. S After striking a foreign object, stop the engine, disconnect the spark plug and inspect the cultivator damage.
- Page 15 SNOW THROWER SAFETY WARNING: Keep hands and feet away from the rotor when starting or running the engine. Never attempt to clear the rotor with the engine/motor running. Stop engine and disconnect spark plug before unclogging snow or debris from discharge chute or when adjusting vanes.
- Page 16 4. Replace with a pre-wound spool, or re- place line using a 4,5 meters length of 2,4 mm diameter McCulloch brand line. WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.
- Page 17 8. Position the lines in the guide slots. Guide slot Guide slot 9. Place the spool in the cover as shown below. 10. Insert the ends of the lines through exit holes in the sides of the cover. Line exit hole Cover 11.
- Page 18 Idle speed screw Air filter cover WARNING: Perform the following steps after each use: S Allow engine to cool before storing or trans- porting. S Store unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.
- Page 19 TROUBLESHOOTING TABLE WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit. TROUBLE CAUSE Engine will not 1. Engine flooded. start. 2. Fuel tank empty. 3. Spark plug not firing. 4.
- Page 20 We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46- -36- -146500, as authorised representative in the Community, declare that the brushcutter model McCulloch Cabrio 433L with serial numbers dating from 2009 and onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S...
- Page 21 TECHNICAL DATA ODEL: Cabrio 433L ENGINE Cylinder displacement, cm At maximum engine power, rpm Maximum rotational frequency of the spindle Engine speed at recommended maximum spindle rotational frequency Recommended speed idling, rpm Maximum engine power, measured in accordance with ISO 8893, kW Catalytic converter muffler IGNITION SYSTEM Spark plug...