Related Manuals for Honeywell HMLCD17e2
Summary of Contents for Honeywell HMLCD17e2
-
Page 1: User Manual
HMLCD17e2, HMLCD19e2 e-Series LCD Monitor User Manual Document 800-00718 – Rev A – 07/07... - Page 2 Revisions Issue Date Revisions July 2007 Initial Release...
-
Page 3: Fcc Compliance Statement
• Plug the system into a different outlet so that the system and the receiver are on different branch circuits. If necessary, consult a representative of Honeywell Inc. or an experienced radio/television technician for additional suggestions. The following information is provides on the device or devices covered in this document in compliance with the FCC regulations: •... - Page 4 Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock. To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor case. Never use your monitor if the power cable has been damaged. Do not allow anything to rest on the power cable. Keep the power cable away from where people could trip over it.
-
Page 5: Table Of Contents
Contents Connecting the Monitor......... . 11 Mounting the Monitor . - Page 6 Contents...
- Page 7 Figures Figure 1 Connecting to external devices ....... . 11 Figure 2 Bottom panel controls .
- Page 8 Figures...
- Page 9 Tables Table 1 D-SUB Pin Settings ........20 Table 2 Power Consumption .
- Page 10 Tables...
-
Page 11: Connecting The Monitor
Connecting the Monitor The e-Series LCD monitor can be used with your video surveillance system and connects to a number of external devices, such as a DVR, VCR or camera. Figure 1 Bottom Panel Controls Figure 2 PC STEREO IN S-VIDEO (Y/C) OUT Y/C separated signal looping output S-VIDEO (Y/C) IN... -
Page 12: Figure 3 Check Input Signal
Connecting the Monitor VIDEO 2(AV2) OUT Composite signal Output for AV2 VIDEO 2(AV2) IN Composite signal Input for AV2 VIDEO 1(AV1) OUT Video looping Output for AV1 VIDEO 1(AV1) IN Composite signal Input for AV1 10. D-SUB IN PC Signal Input 11. -
Page 13: Figure 4 Remote Control
Remote Controller Figure 4 Document 800-00718 Rev A 07/07 Remote Control POWER Turns the power ON or OFF. There may be a few seconds delay before the display appears. SOURCE Select PC or Video (PC/AV1/AV2/S-Video) MUTE Mutes the sound. MENU Activates and exits the On Screen Display (OSD). -
Page 14: Mounting The Monitor
Mounting the Monitor Mounting the Monitor Figure 5 Back of the LCD monitor and mounting... -
Page 15: Controls And Functions
Controls and Functions Front Panel Controls The options available on the front of the LCD monitor mirror those of the remote control. Figure 6 SOURCE Selects the input source and moves from the previous menu. MENU Activates and exits the On Screen Display (OSD). It can also be used to move from the previous menu or status. -
Page 16: Figure 7 Input Source
Controls and Functions OSD Menu Input Source: Select PC, AV1, AV2 or SVIDEO Figure 7 Screen: Figure 8 Brightness Increase or decrease the intensity of the image. Contrast Increase or decrease the intensity (lightness or dimness) of the image. H. position (PC Mode Only) Move image horizontally on screen right or left. -
Page 17: Figure 9 Audio Settings
Phase (PC Mode Only) Adjust the number of horizontal picture elements. Audio: Figure 9 Volume Adjust audio volume. OSD: Figure 10 OSD (On Screen Display) settings H. Position Move the OSD position to right(' ') or left(' '). V. Position Move the OSD position to up('▲') or down('▼'). -
Page 18: Figure 11 Color Settings
Controls and Functions Color (PC Mode): Figure 11 Color settings Color Temp Adjust color temperature to 9300, 6500, user. (note : 9300 is factory default) Adjust red color for user. Green Adjust green color for user. Blue Adjust blue color for user. Utility: Figure 12 Utility settings Recall... -
Page 19: Figure 13 Tv Utility Settings
e-Series LCD Monitor User Manual TV Utility: Figure 13 TV Utility settings Exit Turn off OSD menu. Document 800-00718 Rev A 07/07... -
Page 20: D-Sub Connector Pin Assignments
D-Sub Connector Pin Assignments D-Sub Connector Pin Assignments Figure 14 D-Sub connector pins Table 1 D-SUB Pin Settings Description Red Video Green Video Blue Video Ground Ground Red Ground Green Ground Blue Ground Signal Cable Detect Ground SDA (for DDC) H-SYNC (or H+V SYNC) V-SYNC SCL (for DDC) -
Page 21: Power Management
Power Management This LCD monitor features a power management system to power down upon receipt of a VESA DPMS (Display Power Management Signaling) from a VESA DPMS video card. This monitor enters an appropriate mode through identifying each of the three modes of the signaling system.The stage that the power management system is in is indicated by the LED on the monitor. -
Page 22: Specifications And Parts
Specifications and Parts Specifications and Parts Table 4 Parameter LCD Type Resolution (H x V) Frequency Input Signal Active Display Area (W x H) Packing Dimensions (W x D x H) Weight Power Supply Table 5 Part LCD Monitor Power Cord Remote Control Unit (with batteries) Specifications list Description... - Page 23 Table 5 Part Stereo Cable VGA Cable Power Adapter User Manual Note: technical specifications and parts are subject to change without notice. Document 800-00718 Rev A 07/07 Parts list e-Series LCD Monitor User Manual Quantity...
-
Page 24: Troubleshooting
Troubleshooting Troubleshooting Issue: Possible Solution: Issue: Possible Solution: Issue: Possible Solution: Issue: Possible Solution: No image is displayed on screen. • Check that the power cord has been connected securely into the wall outlet or grounded extension cable or surge protector. •... - Page 25 NOTES:...
- Page 26 ℡ +34.902. 667.800 © 2007 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof.