Page 2
UPDATE LOG SHEET Application Data Page Part # Note(Cause & Solution) S/Bulletin # Use this page to keep any special servicing information. (Service Bulletin, etc.) If only parts number changes, Just change parts number directly on parts list. And if you need more information, please see the service bulletin...
2. Disassembly and Reassembly 2-1. Cabinet and PCB Disassembly 2-1-1. Ass'y Front Removal REMOVE 2 SCREWS. REMOVE 1 SCREW. Remove the Ass’y Front in the direction of arrow. Remove the part of connector. Fig. 2-1 Ass'y Front Removal Samsung Electronics...
Page 6
Remove the part of connector. Remove the part of FPC connection. REMOVE 2 SCREWS. Remove the COVER-HOUSING REMOVE 1 SCREW. and remove the 1 screw. REMOVE 2 SCREWS. Fig. 2-2 Ass'y Left Removal Samsung Electronics...
Page 7
Disassembly and Reassembly 2-1-3. Ass'y LCD Removal REMOVE 1 SCREW. Remove the Ass’y LCD REMOVE in the direction of arrow. 3 SCREWS. REMOVE 1 SCREW. Fig. 2-3 Ass'y LCD Removal Samsung Electronics...
Page 8
Disassembly and Reassembly 2-1-4. Ass'y EVF/CVF Removal REMOVE 1 SCREW. Turning and removing the CVF REMOVE 1 SCREW. Remove the part of FPC connection. Fig. 2-4 Ass'y EVF/CVF Removal Samsung Electronics...
Page 9
Disassembly and Reassembly 2-1-5. Ass'y Rear Removal After tilting the Ass’y Rear to the direction of arrow, remove it. REMOVE 2 SCREWS. Fig. 2-5 Ass'y Rear Removal Samsung Electronics...
Page 10
2-1-6. Ass'y Chassis Removal REMOVE 2 SCREWS. Remove the part of FPC connection. Remove the Ass’y Chassis in the direction of arrow. Remove the part of FPC connection. REMOVE REMOVE 3 SCREWS. 2 SCREWS. Fig. 2-6 Ass'y Chassis Removal Samsung Electronics...
Page 11
REMOVE 2 SCREWS. REMOVE 1 SCREW. A’ REMOVE 2 SCREWS. C’ B’ < Disconnect the FPC> A ------- A’ B ------- B’ C ------- C’ REMOVE 3 SCREWS. Fig. 2-7 Ass'y Camera Removal Samsung Electronics...
Page 12
"B" and remove the Assy-Cover Housing. "B" HINGE-SHAFT REMOVE 2 SCREWS. "A" Remove the Ass’y Link Chassis in the direction of arrow "A". REMOVE 2 SCREWS. REMOVE 4 SCREWS. REMOVE 2 SCREWS. Fig. 2-8 Ass'y Link Chassis Removal Samsung Electronics...
“START/STOP” button. PLAY 27MIN 0: 27:00: 00 ADJ -> V-REF : 6BH Indicates the adjusted values Indicates current adjustment item. S64 L00 FF 01 80 Indicates current value in the ZOOM switch. Samsung Electronics...
SELF TIMER DISPLAY TELE SLOW STILL F.ADV 3. If you want to finish the adjustment mode, you have to do Power Reset. The Power Reset means that you pull out the power source and pull in it again. Samsung Electronics...
Page 17
OPTION RESERVED(fixed value) * Option Model Adj. value Model Adj. value VP-D55 SCD55 VP-D60 SCD60 VP-D65 2. How to adjust Video-Reference (V-REF). 1) Connect video output cable to wave form scope. The wave form scope must be connected to monitor.
Page 18
1) Select ZOOMVR in the video adjustment mode. 2) Adjust ZOOM SW so that the switch is put in the middle of T and W. 3) Adjust ZOOMVR so that the current value of ZOOM SW is equal to the adjusted ZOOMVR value. Samsung Electronics...
Page 19
3. Press the Address selection button(“START/STOP” button) to skip the next address in order to finish the adjustment and store data. After finishing the adjustment, you have to do power reset. The PRML BER will be set to the right adjustment when shipping out video camera and PCB ASSY from factory. Samsung Electronics...
2) Press the "START/PAUSE" button when storing confirmed adjustment value of each adjustment step in EEPROM. 3) There is a flicker on screen after finishing each adjustment step. 4) To clear the adjustment mode, pull out the power source. Samsung Electronics...
Page 23
5 seconds. camera. 3) Set the "CAMERA/VCR" switch to "CAM- ERA" position. STEP 3 4) The OSD appears. Monitor OSD shows "16D XX XX". Then camera adjustment mode has been activated successfully. Note : "XX" indicates variable values. Samsung Electronics...
Page 31
Alignment and Adjustment Addr. Data Name NTSC SCD60 SCD55 VP-D65 VP-D60 VP-D55 CDS_DLY2_SV_SRH CDS_DLY2_SV_SRL CDS_TESTH CDS_TESTL MOTOR DRIVE control MOTOR_HEADER MOTOR_STARTTIME MOTOR_DRIVETIME MOTOR_CHOPPING MOTOR_EXTPIN MOTOR_EVRA MOTOR_EVRB MOTOR_CHECKSUM << AE control >> D_EEP_ae_iris100ire(wdr) D_EEP_ae_target(wdr) D_EEP_ae_avrmin(wdr) D_EEP_ae_hallgainstr D_EEP_ae_halldiftar D_EEP_ae_agcmaptarget AE_target(147)=(147)0{{80h- <80h-(14C)>0AGC_CONN/AGC_MAX}}/80h D_EEP_ae_hallmin...
Page 32
Alignment and Adjustment Addr. Data Name NTSC SCD60 SCD55 VP-D65 VP-D60 VP-D55 b control max/clip_3100_rmaxclip b control max/clip_5100_rmaxclip "The 2nd quadrent, the 4th quadrent TRACKING SPEEDADJUST" D_EEP_awb_margin_right D_EEP_awb_b_start D_EEP_awb_r_start D_EEP_awb_b_gain_pecnt D_EEP_awb_r_gain_pecnt D_EEP_VCR_VREF D_EEP_VCR_TEST D_EEP_VCR_RECCUR D_EEP_VCR_AREF3 D_EEP_VCR_AREF2 D_EEP_VCR_AREF1 LensAdj Adj_Auto_Hall Adj_Auto_Agc_Min...
Page 34
Addr. Data Name NTSC SCD60 SCD55 VP-D65 VP-D60 VP-D55 PI_one move zoom_H PI_one move zoom_L PI_one move focus_H PI_one move focus_L PI_lens check zoom 1 position margin PI_lens check zoom 2 position margin PI_lens check zoom 3 position margin PI_lens check zoom 4 position margin...
Page 35
Alignment and Adjustment Addr. Data Name NTSC SCD60 SCD55 VP-D65 VP-D60 VP-D55 CCD defect detection repeat CCD defect detection POFFSET chroma suppresse when still (normal mode) chroma suppresse when still (AGC mode) DIS_Weight value DIS_Threshold DIS_VGGAINX_TELE AREA DIS_VGGAINX_MIDDLE AREA DIS_VGGAINX_WIDE AREA DIS_V(x)_Criterion_ A if codition = ( | V(x) | >...
Page 36
6) Press the Display button so that OSD shows "174 MF XX XX". 7) Press the START/STOP (Confirm) button. Never impact on the lens when adjusting zoom and focus lens. There's is a flicker on screen after finishing the adjustment. 3-22 Samsung Electronics...
Page 37
8) There's is a flicker on screen after finishing the 7) There's is a flicker on screen after finishing the adjustment. adjustment. Center of Center of white level white level 90IRE 90IRE Optical Optical black level black level 40US 40US Samsung Electronics 3-23...
Page 38
1) Camera mode & 3100˚ K gray scale chart 2) Connect a video output terminal to a vec- torscope and a TV. 65IRE 3) Press the FF(Mode Up)/REW(Mode Down) button so that OSD shows "2F XX XX". 3-24 Samsung Electronics...
Page 39
1500-2000 Lux. 5) Press the PLAY (Data Up)/STOP (Data Down) so that the yellow level is 50IRE. 6) Press the START/STOP (Confirm) button to store data. 7) There's is a flicker on screen after finishing the adjustment. Samsung Electronics 3-25...
Page 40
1500-2000 Lux. 5) Press the PLAY (Data Up)/STOP (Data Down) so that the cyan vector is 284˚ . 6) Press the START/STOP (Confirm) button to store data. 7) There's is a flicker on screen after finishing the adjustment. 3-26 Samsung Electronics...
Page 41
FF (Mode Up) Shift adjustment address to right. REW (Mode Down) Up value. PLAY (Data Up) Down value. STOP (Data Down) Note: In service adjustment mode, button names are different from those in customer function control mode. Samsung Electronics 3-27...
Page 42
Adjust the EVR so that DC voltage is DC 1.1±0.05 V. 10P-BL 24P-LCD Note: In LCD adjustment mode, when shorting "A" of PCB to GND and pressing the START/STOP button, EEPROM stores con- firmed adjustment value. 3-28 Samsung Electronics...
Page 43
Adjust the EVR so that bright level is 3.4 Vp-p. 5) B-Sub Brightness 0.2Vp-p a) TP-B & EVR b) Connect an oscilloscope probe to TP-B. c) Adjust the EVR so that bright level is 3.3 Vp-p. LEVEL (PEDESTAL PEDESTAL Samsung Electronics 3-29...
Page 44
FF (Mode Up) Shift adjustment address to right. REW (Mode Down) Up value. PLAY (Data Up) Down value. STOP (Data Down) Note: In service adjustment mode, button names are different from those in customer function control mode. 3-30 Samsung Electronics...
Page 45
Connect an oscilloscope probe to TP-R. c) Adjust the EVR so that bright level is 7.2 Vp-p. 4) B-Sub Brightness a) TP-B & EVR b) Connect an oscilloscope probe to TP-B. c) Adjust the EVR so that bright level is 7.0 Vp-p. Samsung Electronics 3-31...
Page 46
Adjust the EVR so that yellow level is 0.8 c) Adjust the EVR so that green level is equal Vp-p higher than pedestal level. to red level. (PAL Mode : Adjust so that red carrier is focused on.) LEVEL (PEDESTAL PEDESTAL 3-32 Samsung Electronics...
Page 47
Remote Control Button Location 3-5-2. EVF Adjustment 1) VIDEO GAIN a) Connect an oscilloscope probe to TP-V. 10 PIN CON b) Adjust the VRE02 so that A level is 2.5 Vp-p. 20uS 2 PIN CON A LEVEL Locationof Test Point Samsung Electronics 3-33...
Page 48
Alignment and Adjustment MEMO MEMO 3-34 Samsung Electronics...
Page 49
4. Exploded View and Parts List 4-1. Cabinet Assembly (1) 4-2. Cabinet Assembly (2) 4-3. Cabinet Assembly (3) 4-4. Cabinet Assembly (4) 4-5. Cabinet Assembly (5) 4-10 4-6. Machanical Parts (Main Chassis) 4-12 4-7. Machanical Parts (Sub Chassis) 4-14 Samsung Electronics...
Page 50
Exploded View and Parts List 4-1. Cabinet Assembly (1) Samsung Electronics...