Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C GENERAL CONTENTS INTRODUCTION .......................ii SPECIAL SERVICE TOOLS .....................iii GLOSSARY (Pending) .....................iv COMPONENT IDENTIFICATION..................v SECTIONAL CONTENTS TROUBLESHOOTING DIAGNOSTICS LED DIAGNOSTICS LCD HOW TO…SERVICE ELECTRONICS MISCELLANEOUS...
Page 4
If you do not have a part in stock, a form to order by FAX has been included in Section V for your convenience or you can call Life Fitness Customer Support Services any Monday through Friday from 8:00 AM to 6:00 PM ( C.S.T.
Page 5
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C INTRODUCTION SPECIAL SERVICE TOOL REQUIREMENTS Unless otherwise specified, only basic hand tools are required to perform service procedures outlined in this section. Some of these standard tools should consist of: Philips and Straight- Blade Screw Drivers, Torx Set, Pliers, Rubber Mallet, Pry Bar, Snap Ring Pliers (internal and external), Standard and Metric size Socket Set (3/8 or 1/2 drive), and Standard and Metric size Combination, open-end, or Box Wrenches.
Page 7
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C COMPONENT IDENTIFICATION – C9 and C7 Consumer Bikes Handlebar Console Standard Seat Accessory Tray Seat Pull-Pin Console Post Seat Post Side Shroud Front Wheels Pedal Crankarm C9 Assembly Components Note: C7 will not have accessory tray and handlebars are without electrodes.
Page 8
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C COMPONENT IDENTIFICATION – C9 and C7 Consumer Bikes Shroud Gasket Main Cable Resistor Assembly Alternator Crankshaft Intermediate Pulley Alternator Belt C7 Left Side Components Note: C9 has a 6 volt battery mounted on a bracket above the PCB.
Page 9
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C COMPONENT IDENTIFICATION – C9 and C7 Consumer Bikes Idler Assembly Crank Pulley Bracket Crank Shaft Main Drive Clutch Belt Assembly C7 Right Side Components...
Page 10
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C COMPONENT IDENTIFICATION - LC9500, LC9100, LC8500 Commercial Bikes Handlebar Console Deluxe Seat Accessory Tray Seat Post Console Post Cover Seat Latch Side Shroud Front Wheels Pedal Crankarm...
Page 11
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C COMPONENT IDENTIFICATION - LC9500, LC9100, LC8500 Commercial Bikes Shroud Gasket Main Cable Resistor Assembly Alternator Crankshaft Intermediate Pulley Alternator Belt Lc8500 Left Side Components Note: The Lc9500 and 9100 has a 6 volt battery mounted on a bracket above the PCB.
Page 12
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C COMPONENT IDENTIFICATION - LC9500, LC9100, LC8500 Commercial Bikes Idler Crank Assembly Pulley Bracket Crank Shaft Main Drive Clutch Belt Assembly Lc8500 Right Side Components...
Check auto start not responding. Keypad not responding. Test keypad in diagnostics. Insufficient battery voltage. Check battery voltage. The LC9500, LC9100, and C9i have a 6VDC battery (non-alkaline) which should test at a minimum of 6.0 VDC. The LC8500, and C7 has a 9VDC alkaline battery and it should test at a minimum of 9.0 VDC.
Pedaling to slowly Pedal faster than 35 RPM. constant Insufficient battery voltage Check battery voltage. The LC9500, LC9100, and C9i have a 6VDC battery (non-alkaline) which should test at a minimum of 6.0 VDC. The LC8500, and C7 has a 9VDC alkaline battery and it should test at a minimum of 9.0 VDC.
TROUBLESHOOTING GUIDE SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Upon start of program, excessive Insufficient battery voltage Check battery voltage. The LC9500, resistance load is immediate; no LC9100, and C9i have a 6VDC normal, incremental increase from “no battery (non-alkaline) which should load.”...
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TROUBLESHOOTING GUIDE SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION During MANUAL program, resistance Malfunctioning Alternator Test with substitute Alternator Control variation occurs. Control Board Board. Replace defective board. Malfunctioning Alternator Test Alternator output or, test with substitute Alternator.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TROUBLESHOOTING GUIDE SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Unable to receive any channels when Air/cable setting may not be Follow the setup procedures in the using cable. correct. operator manual.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TROUBLESHOOTING GUIDE – TESTING THE INVERTER BOARD Special Service Tools Required: Multi-meter CAUTION! HIGH VOLTAGE ON CONNECTORS J2 AND J3 Test Points Remove the Integrated System Console from the Unit. 2.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TROUBLESHOOTING GUIDE – TESTING THE POWER SUPPLY CABLE Special Service Tools Required: Multi-meter 1. Unscrew the Retaining Nut securing the Power Positive Cable Plug. Remove the Cable. 2.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C Test/service All Led’s On Display Test Units Keypad Test Walking Led Alt. Voltage Relay Port I/o Test Alt Rpm Fld Kick Entertainment Language...
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C ENTRY LEVEL C o d e v e r - 1 3 0 Hold down the number 5 key (9500) or the UP ARROW key on (non-9500 units), then the press the CLEAR key twice.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TEST/SERVICE ALL LEDS AND KEYPAD TEST On entry to this state, all of the LEDs will turn ON. Pressing the keys will result in a beep sound for all but the START, ENTER and CLEAR keys, a character repeated across the message center will be displayed.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TEST/SERVICE - WALKING LED TEST Message Center Profile Window On entry to this state, the LED segments in the MESSAGE CENTER and the PROFILE WINDOW will give the animated effect of moving, henceforth, 'Walking LED."...
Load duty cycle ranges from 0-320 for LC9500 model, 0-280 for LC9100 and C9I models, and 0-415 for LC8500 and C7i models. This value can be adjusted using the Time Up and Time Down arrow keys on the LC9500 console, and the UP and DOWN arrow keys on all other models.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TEST/SERVICE - MISCELLANEOUS 2 TESTS REED SWITCH RPM: In the Distance Window, the Reed Switch RPM is displayed. Note: The Reed Switch RPM will not display when the alternator is running. RPM: In the RPM window, the alternator RPM will be displayed.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TEST/SERVICE - PORT I/O TEST Press the ENTER key to advance to the next diagnostic state. Press the CLEAR key to the previous diagnostic state, or repeated pressing to exit diagnostics.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TEST/SERVICE - LIFE PULSE TEST C - O G 9 9 Upon initial entry to this test, a heart-shaped image will be displayed in the profile window along with two messages in the message center when the user has both hands on the LifePulse sensors.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TEST/SERVICE - CSAFE NETWORK TEST Within this state, the CSAFE network can be tested. This is how you can check to see if you’re receiving any communications from the network system. 1.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TEST/SERVICE - EEPROM TEST This diagnostic state tests the Display Console EEPROM by reading, writing, and replacing all used locations in the Display Console EEPROM. The EEPROM location being tested will appear in the display message center. Pressing the DOWN ARROW will initiate the EEPROM test.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TEST/SERVICE - TELEMETRY ENABLE/DISABLE T E L E M E T R Y O F F Within this state, the TELEMETRY can be turned ON or OFF. If a telemetry heart rate is detected, it will be displayed when telemetry is set to ON.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C TEST/SERVICE - LANGUAGE L A N G E N G L I S H Within this state, one of seven languages can be selected to include: English, German, French, Italian, Dutch, Spanish or Portuguese.
Page 44
Within this state, the MAXIMUM PROGRAM DURATION is displayed and can be adjusted from a range of 1-99 minutes on the LC9100, LC8500, C9i, and C7i. LC9500 can be adjusted from 10-99 minutes. The DOWN ARROW will decrease the value by 1 minute. Key will Auto-Repeat if held.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C OPTIONAL SETTINGS - ENGLISH/METRIC UNITS E N G L I S H U N I T S Within this state, ENGLISH or METRIC units can be selected. The DOWN ARROW will select METRIC units.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C OPTIONAL SETTINGS - WATTS DISPLAY ENABLE/DISABLE W A T T D I S P L A Y O F F If this option is enabled, the MESSAGE CENTER displays the Watts equivalent of the workload. This message will only be displayed after a level change.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C OPTIONAL SETTINGS - METS DISPLAY ENABLE/DISABLE M E T S D I S P L A Y O F F If this option is enabled, the MESSAGE CENTER displays the METs equivalent of the workload. This message will only be displayed after a level change.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C OPTIONAL SETTINGS - CAL/HR DISPLAY ENABLE/DISABLE C A L / H D I S P O F F If this option is enabled, the MESSAGE CENTER displays the Calories/Hour equivalent of the workload. This message will only be displayed after a level change.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C OPTIONAL SETTINGS - WATTS PROGRAM ENABLE/DISABLE W A T T D I S P L A Y O F F If this option is enabled, the MESSAGE CENTER displays the Watts equivalent of the workload. This message will only be displayed after a level change.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C OPTIONAL SETTINGS - METS PROGRAM ENABLE/DISABLE M E T S P R O G R A M O F F Within this state, METS PROGRAM can be turned ON or OFF. By default, the LifeCycle will have the METS PROGRAM OFF.
Page 51
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C OPTIONAL SETTINGS - TOTAL HOURS AND STATISTICS H O U R S = Upon entry to this state, TOTAL HOURS are displayed. STATISTICS can be displayed using the UP and DOWN arrow keys. The UP ARROW allows scrolling through the available programs and shows the number of times each program has been selected.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C OPTIONAL SETTINGS - ENTERTAINMENT CONTROLS ON/OFF (LC9500 ONLY) Channel or Volume Control The ENTERTAINMENT CONTROL SETTING Using the arrow keys will turn ON or OFF the entertainment (cardio theater/broadcast vision) controls for the CSAFE PORT output for volume and channel change.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C OPTIONAL SETTINGS - PHOTO SHOOT 1 3 5 2 . 1 8 8 2 1 7 . 4 4 Data displayed in the message center is non-functional and intended only to simulate values for photographic sessions.
Page 55
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C SECTION IIB DIAGNOSTIC MODES 95Ce LCD UNIT ONLY Page Welcome Screen ....................... 3 Workout Screen ......................... 4 Main Menu ......................... 5 System Test Menu ......................6 System Diagnostics......................7 Test Engineering ........................
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD ONLY WELCOME SCREEN LCD Console Welcome Screen The Welcome Screen initially appears after Power-Up or when the bike is not in use. Touching the Screen will change the screen to the WORKOUT SELECTION screen.
From the Workout Selection Screen you will be able to enter the Systems Option Menu. To enter, go to the Workout Selection Screen then press and hold the COOLDOWN key, and then double-touch the Life Fitness icon. After entering the System Options the Main Menu will appear. For further information about the...
Page 59
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD SYSTEM OPTIONS – MAIN MENU The System Options - Main Menu selections, when pressed, allows access to the System Test Menu, Information Menu, and Configuration Menu. Pressing the screen Exit key will return you back to the Workout Selection Screen.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD SYSTEM TEST MENU The System Test Menu allows the user to access the above by pressing the appropriate key. Pressing the screen Back key will return you to the System Options – Main Menu screen.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD SYSTEM DIAGNOSTICS In the SYSTEM DIAGNOSTICS screen the feedback from various sources can be read. SYSTEM VOLTAGE Displays the voltage present at the console. ALTERNATOR VOLTAGE Displays the voltage out of the Alternator.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD TEST ENGINEERING All status windows on this screen should display OFF and should not be changed unless instructed to do so by Life Fitness Customer Support.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD TELEMETRY TEST The circles in the Telemetry Box indicate whether Telemetry is Enabled or Disabled. Touching the appropriate circle can enable or disable Telemetry. The Heart rate value window will display the users Heart Rate when Telemetry is enabled.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD LIFE PULSE TEST The LifePulse™ System can be tested manually. The system will display a “Hands-On” reading when the user has placed their hands on the LifePulse™ Sensors. A timer will commence (and will show in the Acquisition Time window ) from the time both Hands-On condition occurs to when the LifePulse system can generate a heart rate reading.
Page 65
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD CSAFE TEST CSafe Test - Not Available at This Time.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD EEPROM TEST Pressing the screen EEPROM Internal Test key allows testing of the EEPROM on the Single Board Computer. Pressing the screen EEPROM External Test key allows testing of the EEPROM on the Interface Board. In either instance, a PASS message will appear if the EEPROM is good Pressing the screen Back button will return you to previous screen.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD INFORMATION MENU STATISTICS Displays various historical data regarding individual workout program usage and critical system power levels. SOFTWARE VERSIONS Displays current software version information. Displays historical information regarding system errors encountered during SYSTEM ERRORS operation.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD INFORMATION STATISTICS Entry to this screen allows to user to view statistics such as: total hours of use on the unit and hours of use per program used along with other information.
This screen allows the user to view the current software programs loaded into the unit along with its corresponding Life Fitness part number if applicable. Pressing the screen Back key will return you to System Options – Main Menu screen. Pressing the screen MAIN...
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD SYSTEM ERRORS This screen allows the user to view system errors that have been logged into the unit’s memory. Pressing the screen Back key will return you to System Options – Main Menu screen. Pressing the screen MAIN MENU key will return you back to the MAIN MENU.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD USAGE LOG REPORT This screen allows the user to view detailed information in relation to RPMs used at different levels. Pressing the screen Back key will return you to System Options – Main Menu screen. Pressing the screen MAIN MENU key will return you back to the MAIN MENU.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD CONFIGURATION MENU MANAGER Supervisory workout parameter setup. MANUFACTURER Critical system parameter setup. Television configuration. TOUCH SCREEN CONFIGURATION Proximity calibration of touched screen. Pressing the screen Back key will return you to System Options – Main Menu screen. Pressing the screen MAIN MENU key will return you back to the MAIN MENU.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD MANAGER’S CONFIGURATION Maximum Workout Duration: Allows the manager to set a maximum workout limit between 1 and 99 minutes. The time can be modified using the up or down arrow keys. The unit default is 60 minutes. Standby Configuration: Sets the desired amount of time of inactivity before the system automatically turns the LCD screen backlight off.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD CUSTOM MESSAGE SETUP This configuration allows for a custom message to be displayed across the Welcome Screen. Creating/changing a Custom Message—after entering the Manager’s Configuration, check to make sure that Custom Message is enabled, and then select Custom Message Setup.
DISPLAY CONSOLE 95Ce LCD MANUFACTURERS CONFIGURATION MENU Access to this screen will only be available to Life Fitness certified technicians. Pressing the screen Back key will return you to System Options – Main Menu screen. Pressing the screen MAIN MENU key will return you back to the MAIN MENU.
Page 76
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD TV CONTROLS This screen brings up the TV screen and allows adjustment of brightness, contrast, saturation and hue. Also allows the choice of TV format, antenna setup and channel setup. To Set up channels: Select Auto in Channel Setup and then press Start.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD MAX VOLUME SETUP Entry to this screen allows the user to adjust Volume by using the Arrow keys. Note: Headphones must be used for this function. The upper set of arrows adjusts the volume capacity higher or lower, allowing clubs to compensate for average noise levels within the club.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE 95Ce LCD TOUCH SCREEN CONFIGURATION Entry into this screen will allow to user to reconfigure the Touch Screen. The display will show a blank screen with a + sign in the middle.
Page 79
Main Wire Harness......................22 9 Volt Console Battery (LC8500 and C7) ................23 6 Volt Battery on Frame (LC9500, 9100, and C9)............... 24 Display Console and Accessory Tray.................. 25 Console Post Assembly, Main Cable, and Coax Cable for LCD ......... 26 Power Control Board (LC8500 and C7) ................
Page 81
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove Pedals, Crank Arms, and Shrouds Special Service Tools: NONE Seat Post Covers NOTE: Each shroud can be removed independently of each other. This procedure covers removal of the right shroud first and then the left shroud.
Page 82
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove Pedals, Crank Arms, and Shrouds - Continued Special Service Tools: NONE 4. Remove three screws from the left crank hub, and then remove the left crank arm from the crank shaft with pedal attached.
Page 83
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Crank Shaft Hub Assembly Special Service Tools: Bearing Service Tool Kit – Part Number: BearingToolKit Right Pedal/ Crank Arm 1. Remove the crank arm with pedal from the defective crank shaft hub.
Page 84
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Crank Shaft Hub Assembly - Continued Special Service Tools: Bearing Service Tool Kit – Part Number: BearingToolKit 5. Install the disc puller plate as illustrated on the Forcing Bolt Mounting Bolt(3) left hub.
Page 85
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Crank Shaft Bearings Special Service Tools: Bearing Service Tool Kit – Part Number: BearingToolKit Thrust Thrust Washer Snap Ring Washer (Large) (Large) (Small) Thrust Thrust Washer...
Page 86
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Crank Shaft Bearings - Continued Special Service Tools: Bearing Service Tool Kit – Part Number: BearingToolKit 8. Press out the needle bearings by rotating Threaded Rod the hex nut clockwise until the bearings drop into the puller hub.
Page 87
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Crank Shaft Bearings - Continued Special Service Tools: Bearing Service Tool Kit – Part Number: BearingToolKit 11. Start tightening the hex nut. You may have to Threaded Rod hold the spacer to stop it from turning.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Clutch Assembly Special Service Tools: NONE 1. Remove the right side shrouds. Refer to, How To…Remove Pedals, Pedal Levers, and Side Covers. 2. Remove the main drive belt. Refer to, How To…Remove Main Drive Belt.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Intermediate Pulley Shaft and Bearings Special Service Tools: Bearing Service Tool Kit – Part Number: BearingToolKit 1. Remove the side covers. Refer to, How To…Remove Pedals, Pedal Levers, and Side Shrouds. Intermediate Main Drive Intermediate...
Page 90
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Intermediate Pulley Shaft and Bearings - Continued Special Service Tools: Bearing Service Tool Kit – Part Number: BearingToolKit 6. Turn the forcing screw clockwise to press out the pulley shaft assembly from the bearings and spacer. 7.
Page 91
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Intermediate Pulley Shaft and Bearings - Continued Special Service Tools: Bearing Service Tool Kit – Part Number: BearingToolKit 9. Turn the hex nut clockwise to push the 1 bearing out into the hub.
Page 92
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Intermediate Pulley Shaft and Bearings - Continued Special Service Tools: Bearing Service Tool Kit – Part Number: BearingToolKit 15. Start tightening the hex nut to press in the bearings. Continue pressing in the bearings until the thrust washers(2) stop against the housing shoulder as shown.
Page 93
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Intermediate Pulley Shaft and Bearings - Continued Special Service Tools: Bearing Service Tool Kit – Part Number: BearingToolKit 19. Press in the pulley/shaft until the shaft bottoms against the 2 bearing.
Page 94
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Idler Roller Special Service Tools: NONE Note: The crank pulley and idler bracket are shown removed for clarity purposes Idler Bracket only. Neither have to be removed to remove the idler roller.
Page 95
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Main Drive Belt Special Service Tools: NONE 1. Remove the right pedal, right crank arm, and right shroud. See "How To…" in this section.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Alternator Special Service Tools: Belt Tensioning Gauge Alternator Tensioning Bolt, Alternator Lock Washer, Wiring Flat Washer Alternator Alternator Belt Alternator Mounting Bolt/Washer Alternator Washer/ Lock Nut 1.
Page 97
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Alternator Belt Special Service Tools: Belt Tensioning Gauge 1. Remove the pedals, crank arms, and side shrouds. See "How To…" in this section. 2.
Page 98
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Seat Post Assembly (Latch LC8500, 9100, 9500) Special Service Tools: NONE 1. Remove the side shrouds. Refer to, How To…in this section. 2. Remove two screws on the seat post collar. 3.
Page 99
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Seat Post Assembly (Pull-Pin C7 and C9) Special Service Tools: NONE Seat 1. Remove the side shrouds. Refer to, How To…in this section. 2.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Main Wiring Harness Special Service Tools: NONE 1. Remove the side shrouds. Refer to, How To… in this section. 2. Remove the handlebar. Refer to, How To… in this section.
Page 101
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the 9-Volt Console Battery (LC8500 and C7) Special Service Tools: NONE NOTE: The 9 Volt console battery is located Back of the back of the console. Console Assembly 1.
Page 102
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the 6-Volt Battery (LC9500, 9100 and C9) Special Service Tools: NONE 1. Remove the side shrouds. Refer to, How To…in this section. 6 Volt 2.
Page 103
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Display Console and Accessory Tray Special Service Tools: NONE 1. Remove four mounting screws from the Accessary back of the console at the console Tray Screws support.
Page 104
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Console Post Assembly, Main cable and Coax (on LCD only) Special Service Tools: NONE End Cap Console Post Console Post Console Cable Console Support Elbow and Screws Console...
Page 105
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Power Control Board (LC8500 and C7) Special Service Tools: NONE Main Cable Bracket Board Mounting Screws 1. Remove the left pedal and crankarm, and then remove the left side shroud. 2.
Page 106
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Power Control Board (LC9500, 9100 and C9) Special Service Tools: NONE Battery Mounting Screws(4) Remove the left pedal and crankarm, and then remove the left side shroud.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Pedal Special Service Tools: NONE 1. Remove the right pedal using an open end wrench and loosening the pedal shaft by rotating it counterclockwise.
Page 108
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Front Wheels Special Service Tools: NONE 1. Remove the two wheel insert screws from each side of the front stabilizer. 2. Pull out the wheel bearing and wheel insert together.
Wiring Handlebar Note: C7, LC8500, and LC9100 have no Mounting heart rate sensors. Screws 4. Remove the handlebar. 5. Install the handle bar in reverse order. C9 and Lc9500 Handlebar Assembly C7, Lc8500, and Lc9500 Handlebar...
Page 110
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Heart Rate Sensor (LC9500 and C9) Special Service Tools: NONE Electrode Molder Grip Molded Insert Cable Assembly Cable Assembly Handlebar End Cap Insulated Plug...
Page 111
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Telemetry Receiver and Telemetry Receiver Cable (LC9500, 9100, 8500, and C7) Special Service Tools: NONE Telemetry Receiver 1. Remove four screws securing the top sensor cover.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Resistor Assembly Special Service Tools: NONE CAUTION! BEFORE REPLACING Mounting CIRCUIT BOARD(S), GROUND Screws YOURSELF TO EARTH GROUND USING AN ANTI-STATIC GROUND Resistor STRAP.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Remove the Auto Start Switch and Bracket Special Service Tools: NONE CAUTION! BEFORE REPLACING CIRCUIT BOARD(S), GROUND Auto Start YOURSELF TO EARTH GROUND USING AN ANTI-STATIC GROUND Switch Cable STRAP.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C LCD Integrated Console Service Overview Special Service Tools Required: NONE CAUTION! BEFORE REPLACING CIRCUIT BOARD(S), GROUND YOURSELF TO EARTH GROUND USING AN ANTI-STATIC GROUND STRAP. NOTE: The following pages provide service procedures for servicing the LCD Integrated Console. While the Console Housings may differ between the various products, the internal components, which make up the Console, are identical.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Headphone Jack Special Service Tools Required: NONE CAUTION! BEFORE REPLACING CIRCUIT BOARD(S), GROUND YOURSELF TO EARTH GROUND USING AN ANTI-STATIC GROUND STRAP. Note: For clarity purposes the Console is shown off the unit. Headphone Jack replacement does not require removal of the Console from the unit.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Inverter Board Special Service Tools Required: NONE CAUTION! BEFORE REPLACING CIRCUIT BOARD(S), GROUND YOURSELF TO EARTH GROUND USING AN ANTI-STATIC GROUND STRAP. Back Cover 1.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Single Board Computer Special Service Tools Required: NONE Single Board Computer Single Board Computer Mounting Screws (7) 5-Pin Touch Screen 24-Pin Connector Receptacle Communication Connector Connector...
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Interface Board Special Service Tools Required: NONE CAUTION! BEFORE REPLACING CIRCUIT BOARD(S), GROUND Mounting YOURSELF TO EARTH GROUND USING AN ANTI-STATIC GROUND STRAP. bracket 1.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Touch Screen Assembly Special Service Tools Required: NONE CAUTION! BEFORE REPLACING CIRCUIT Touch Screen BOARD(S), GROUND YOURSELF TO EARTH Assembly GROUND USING AN ANTI-STATIC GROUND STRAP.
Page 121
Display Console Board - Model C7 ..................10 Display Console Board - Model C9 ..................12 Alternator Control Board - Model C7 and LC8500 .............. 14 Alternator Control Board - Model C9, LC9100, and LC9500..........15 Alternator..........................17 Wiring Block Diagram LC8500 and C7................18 Wiring Block Diagram C9 ....................
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE BOARD - Model LC9500 Functional Description The Display Console Board is designed to work in conjunction with the Alternator Control Board. It reads the keypad input for changes or updates by the user, and refreshes the status LEDs, data display, and profile display matrix.
Page 124
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE BOARD - Model LC9500 Connector and Pin Descriptions Connector Location Functional Description P2 is a 16 pin connector that N.C. connects to the alternator GND (NOT USED) control board.
Page 125
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE BOARD - Model LC9500 Connector and Pin Descriptions Connector Location Functional Description P5 is a 24 pin connector that connects to the lower console display board.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE BOARD - Model LC9100 Functional Description The Display Console Board is designed to work in conjunction with the Alternator Control Board. It reads the keypad input for changes or updates by the user, and refreshes the status LEDs, data display, and profile display matrix.
Page 127
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE BOARD - Model LC9100 Connector and Pin Descriptions Connector Location Functional Description P2 is a 16 pin connect that N.C. connects to the alternator GND (NOT USED) control board.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE BOARD - Model LC8500 Functional Description The Display Console Board is designed to work in conjunction with the Alternator Control Board. It reads the keypad input for changes or updates by the user, and refreshes the status LEDs, data display, and profile display matrix Connector and Pin Descriptions Connector...
Page 129
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE BOARD - Model LC8500 Connector and Pin Descriptions Connector Location Functional Description N.C. P2 is a 16 pin connector that GND (NOT USED) connects to the alternator VSYS (NOT USED) control board.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE BOARD - Model C7 Functional Description The Display Console Board is designed to work in conjunction with the Alternator Control Board. It reads the keypad input for changes or updates by the user, and refreshes the status LEDs, data display, and profile display matrix.
Page 131
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE BOARD - Model C7 Connector and Pin Descriptions Connector Location Functional Description P2 is a 16 pin connector that N.C. connects to the alternator GND (NOT USED) control board.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE BOARD - Model C9 Functional Description The Display Console Board is designed to work in conjunction with the Alternator Control Board. It reads the keypad input for changes or updates by the user, and refreshes the status LEDs, data display, and profile display matrix.
Page 133
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C DISPLAY CONSOLE BOARD - Model C9 Connector and Pin Descriptions Connector Location Functional Description P2 is a 16 pin connector that N.C. connects to the alternator GND (NOT USED) control board.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C ALTERNATOR CONTROL BOARD - Model C7 and LC8500 Functional Description The Alternator Control Board is designed to regulate the alternator voltage by modulating the field current. It regulates the pass current (RPM signal) from the Alternator to the Console, and the pass current form the alternator to the load...
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C ALTERNATOR CONTROL BOARD - Model C9, LC9100, and LC9500 Functional Description The Alternator Control Board is designed to regulate the alternator voltage by modulating the field current.
Page 136
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C ALTERNATOR CONTROL BOARD - Model C9, LC9100, and LC9500 Connector Location Functional Description P2 Connector is a 12 pin Molex connector that connects to the Alternator. RPM-ALT...
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C ALTERNATOR Functional Description The 12 volt, 35 amp Alternator is designed to provide electrical power to the product, supply load resistance while providing electrical power, and provide the RPM signal from the AC TAP to the Alternator Control Board.
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C WIRING BLOCK DIAGRAM LC8500 and C7 Vsysc Signal Polar Receiver and Cable optional on Lc8500 and standard on C7. Also comes with Telemetry Strap.
Page 147
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C SECTION V MISCELLANEOUS Page Model Identification & Serial Number Location ..............2 Preventative Maintenance Tips ................... 3 Safety Instruction ........................ 4...
Page 148
Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C MODEL IDENTIFICATION and SERIAL NUMBER LOCATION Serial Number Label Patent Label Bottom Front...
Page 150
Parts Listing prior to setting the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer Support Services at the number listed in the Operation Manual. Save the shipping cartons in case of return.