Honeywell Dolphin 70e Black User Manual

Honeywell Dolphin 70e Black User Manual

With windows embedded handheld 6.5
Hide thumbs Also See for Dolphin 70e Black:
Table of Contents

Advertisement

Dolphin™ 70e Black
®
with Windows
Embedded Handheld 6.5
User's Guide

Advertisement

Table of Contents
loading

Summary of Contents for Honeywell Dolphin 70e Black

  • Page 1 Dolphin™ 70e Black ® with Windows Embedded Handheld 6.5 User’s Guide...
  • Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
  • Page 3: Table Of Contents

    Table of Contents Chapter 1 - Dolphin 70e Black Terminal Agency Information Label Locations ........................1-1 LED Safety ...........................1-1 LED Safety Statement....................1-1 UL and C-UL Statement.......................1-2 Approvals by Country......................1-2 R&TTE Compliance Statement—802.11a/b/g/n, Bluetooth, and/or GSM......1-2 FCC Requirements ......................1-3 Dolphin RF Terminal—802.11a/b/g/n, Bluetooth, and/or GSM ........1-3 Canadian Compliance......................1-3...
  • Page 4 Features of the Dolphin 70e Black ..................3-4 Front, Bottom, and Right Panels..................3-4 Back, Top, and Left Panels.................... 3-7 The I/O Connector ......................3-10 Battery ..........................3-10 Charging Options......................3-11 Charging Times ......................3-11 Important Charging Guidelines ..................3-11 Battery Error Notification....................
  • Page 5 Connecting the Terminal to a Wireless Network............7-12 Adding Programs Using the Internet................7-12 Software Upgrades......................7-13 Dolphin 70e Black COM Port Assignment Table............... 7-13 Chapter 8 - Working with Wireless Wide Area Networking (WWAN) Overview..........................8-1 Requirements ........................ 8-1 Antenna Band ........................
  • Page 6 Selecting the Port ......................10-1 COM7 .......................... 10-2 GPS Intermediate Driver....................10-2 GPS Demo ........................10-2 Chapter 11 - Dolphin 70e Black HomeBase Device (Model 70e-HB) Overview..........................11-1 Unpacking the HomeBase ................... 11-1 Charging Overview ...................... 11-1 Communications ......................11-1 Convenient Storage .....................
  • Page 7 Requirements ......................11-7 Setting Up and Connecting the Dolphin Terminal to the HomeBase......11-7 Mounting the HomeBase ....................11-7 Desk Mounting......................11-7 Chapter 12 - Dolphin 70e Black ChargeBase Device (Model 70e-CB) Overview..........................12-1 Unpacking the ChargeBase..................12-1 Charging Overview ...................... 12-1 Convenient Storage .....................
  • Page 8 viii...
  • Page 9: Chapter 1 - Dolphin 70E Black Terminal Agency Information

    Dolphin 70e Black Terminal Agency Information Dolphin 70e Black mobile computers meet or exceed the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Read these guidelines carefully before using your Dolphin terminal.
  • Page 10: Ul And C-Ul Statement

    2006/95/EC Low Voltage Directive when supplied with the recommended power supply. Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.
  • Page 11: Fcc Requirements

    High power radars are the primary users of 5250-5350 MHz and 5650-6850 MHZ bands. This may cause interference to Wireless Local Area Network devices. European Contact: Hand Held Products Europe B.V. Nijverheidsweg 9-13 5627 BT Eindhoven The Netherlands FCC Requirements Dolphin RF Terminal—802.11a/b/g/n, Bluetooth, and/or GSM This device complies with Part 15 of the FCC Rules.
  • Page 12: Rf Exposure Information (Sar)

    5Ghz band: UNII (Unlicensed National Information Infrastructure) or band1 (5.150 to 5.250 GHz) is restricted to indoor use only. Any other use will make the operation of the device illegal. For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines for use with the following body worn accessory: Holster-1.
  • Page 13: For European Community Users

    FCC RF exposure guidelines. For European Community Users Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE). Waste Electrical and Electronic Equipment Information This product has required the extraction and use of natural resources for its production.
  • Page 14: Pacemakers, Hearing Aids And Other Electrically Powered Devices

    IEC specification. Hearing Aid Compatibility (HAC) Dolphin 70e Black models 70eLGN and 70eLG0 have been tested for hearing aid compatibility. These devices have an M4 and T4 rating. For additional HAC information, including the HAC rating for this product, please refer to www.honeywellaidc.com.
  • Page 15: Chapter 2 - Getting Started

    Dolphin terminal should need to be returned for service. Note: Your Dolphin model may differ from the model illustrated in this guide; however, the features noted are standard for all Dolphin 70e Black models with Windows® Embedded Handheld unless otherwise indicated. Initial Setup for Dolphin 70e Black Terminals Step 1.
  • Page 16 Dolphin terminals ship with the battery significantly discharged of power. After installing the battery in the terminal, charge the battery with a Dolphin 70e Black charging peripheral for a minimum of 4 hours for the standard battery pack or 6 hours for the extended battery pack. When using the 70e-USB Charge/ Communication cable to charge from a 500mA USB port on a host device, charge the battery for a minimum of 6 hours for the standard battery and 8 hours for the extended battery.
  • Page 17: Using The Usb Charge/Communication Cable (Model 70E-Usb Adapterkit)

    Option 1: Charging from a power outlet Use only a UL Listed power supply, which has been qualified by Honeywell with an output rated at 5VDC and 1A with the device. Right Side Panel of Dolphin 70e Black...
  • Page 18 USB Door Right Side Panel of Dolphin 70e Black Micro USB Port USB Port on Host Device USB Charge/ Communication Cable Step 3. Boot the Terminal and Access the Home Screen The terminal begins booting as soon as power is applied. Do not press any keys or interrupt the boot process.
  • Page 19: The Home Screen

    The Home Screen After the Dolphin terminal initializes, the Home screen appears. Title Bar (page 2-5) Touch a menu item to access additional screens. Swipe up or down with your finger or stylus to scroll through the menu items. Touch to access Tile Bar (page 2-8)
  • Page 20 Call on hold Missed call Data call in progress A battery error has occurred. Replace the main battery with a Honeywell Li-ion battery pack. Battery is has a full charge Battery has a high charge Battery has a medium charge...
  • Page 21 Icons in the Title Bar Indicator Meaning No SIM card is installed Active network connection No active network connection GPRS available GPRS connecting GPRS in use HSDPA available HSDPA connecting HSDPA in use EDGE available EDGE connecting EDGE in use UMTS available UMTS connecting UMTS in use...
  • Page 22: Horizontal Scroll

    Touch to toggle the virtual keyboard display on or off. Note: When you touch an hold the keyboard icon, a pop-up menu allows you to switch between the default enhanced Honeywell virtual keyboard, which is fully customizable or the standard Windows Embedded Handheld virtual keyboard.
  • Page 23 There are two software components required for customizing the enhanced Honeywell Virtual keyboard. • The first is the Honeywell Virtual Keypad Creator , which resides on your PC and is used to design, save, and download custom keyboard layouts to your Dolphin terminal.
  • Page 24: The Start Menu

    The Start Menu To see the programs loaded on your terminal, touch to access the Start menu. Navigating the Start Menu • Swipe up or down with your finger or stylus to scroll through the menu icons. • To open a program, touch once on the program icon. •...
  • Page 25: File Explorer

    File Explorer You can use the File Explorer to find files and organize files into folders. Touch > File Explorer Touch on the name to open a file or folder. Touch to access additional Menu options. Touch to toggle the virtual keyboard display on or off.
  • Page 26: File Provisioning On The Dolphin 70E Black

    \Honeywell The Honeywell partition or root file system partition is persistent over a hard reset, soft reset, and the removal of the battery pack or the removal of AC power. However, during a kernel upgrade the root file system is reformatted so all data in the folder is deleted and replaced by any files in the \IPSM\Honeywell folder as part of the upgrade process.
  • Page 27: Turning Power On/Off

    Turning Power On/Off To turn the terminal On, press the Power button To turn the terminal Off: 1. Press and hold the Power button for approximately 4 seconds until the options menu displays. 2. Touch Power off. Suspend Mode Suspend mode differs from Power off mode. Power off mode is the equivalent to having no battery or external power source connected to the device.
  • Page 28: Resetting The Terminal

    Note: Do not attempt to use the terminal without the battery door installed. 4. The terminal begins booting as soon as power is applied. We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty.
  • Page 29 A Soft Reset (Warm Boot) re-boots the device and preserves any objects created in RAM. You would perform a soft reset when: the terminal fails to respond, after installing some software applications, or after making changes to certain system settings, such as network cards. A Hard Reset (Cold Boot) re-boots the terminal and closes any open applications running in RAM at the time of the reset.
  • Page 30 2 - 16...
  • Page 31: Chapter 3 - Hardware Overview

    Hardware Overview Standard Configurations for the Dolphin 70e Black WLAN, WPAN & Camera • Microsoft Windows Embedded Handheld 6.5 Professional • TI OMAP3715 1.0GHz Processor • 512MB RAM X 1GB Flash • 3.7V Li-ion rechargeable standard or extended battery pack •...
  • Page 32: Peripherals For The Dolphin 70E Black

    Dolphin 70e Black HomeBase (Model 70e-HB) The Dolphin 70e Black HomeBase device is a charging and communication cradle equipped with a USB host port that is Hi-Speed 2.0v compliant, which enables the terminal to interface with the majority of PC- based enterprise systems.
  • Page 33: Accessories For The Dolphin 70E Black

    Connecting and Synchronizing the Terminal and Workstation on page 7-9. Holster (Model HOLSTER-1) The holster provides convenient storage for the Dolphin 70e Black terminal in mobile environments. The holster features an integrated belt clip and spare battery pouch. Wrist Lanyard (Model SL-LANYARD-1) The black wrist lanyard attaches to the bottom corner of the terminal providing additional security from accidental drop during terminal use.
  • Page 34: Features Of The Dolphin 70E Black

    Features of the Dolphin 70e Black Note: Your Dolphin model may differ from the model illustrated; however, the features noted are standard for all Dolphin 70e Black models with a Windows Embedded Handheld OS unless otherwise indicated. Front, Bottom, and Right Panels...
  • Page 35 By default, the Home button returns you to the Home screen, see page 2-5. The Home button is one of six programmable buttons on the Dolphin 70e Black. You can reassign the button to launch applications or execute commands. For additional information, see Changing Button...
  • Page 36 Right Scan/Image Button By default, the right button triggers the scanner/imager. You can reassign the button to launch applications or execute commands. For additional information, see Changing Button Assignments on page 6-5. Scan Button The Scan button is centrally located for easy access with the right or left hand. By default, the button activates the scanner/imager.
  • Page 37: Back, Top, And Left Panels

    * WWAN equipped models only Note: Your Dolphin model may differ from the model illustrated; however, the features noted are standard for all Dolphin 70e Black with Windows Embedded Handheld models unless otherwise indicated. For a description of each callout,...
  • Page 38 The 3.5mm audio jack supports both speaker (stereo) and microphone (mono) headsets. Battery Dolphin 70e Black model terminals are designed for use with battery part numbers BAT-STANDARD-01 (Li-ion 3.7 V, 6.179 watt hour) and BAT-EXTENDED-01 (Li-ion 3.7 V, 12.358 watt hour) manufactured for Honeywell International Inc. For information on how to...
  • Page 39 The expansion socket is located under the battery door and battery. Note: Honeywell recommends the use of Single Level Cell (SLC) industrial grade microSD or microSDHC memory cards with Dolphin terminals for maximum performance and durability.
  • Page 40: The I/O Connector

    The primary power source for the Dolphin terminal is the 3.7V Li-ion rechargeable battery located under the battery door on the back panel of the device. Honeywell recommends, you keep the battery in the terminal charged at all times to help prevent data loss. Letting the battery become fully discharged causes the terminal to lose all data in RAM.
  • Page 41: Charging Options

    • Dolphin 70e Black ChargeBase Device (Model 70e-CB), see page 12-1 • Dolphin 70e Black USB Charge/Communication Cable (Model 70e-USB ADAPTERKIT), see page 2-3 When the main battery is not installed in the terminal: • Place the battery pack in the...
  • Page 42 To verify your terminal is not drawing more current then supplied by the charging source: 1. Touch > Settings > System > Battery when the terminal is connected to a charging source. 2. Check the Battery Current. If the current is positive, then charging current is going into the battery. If the current is negative, the battery is discharging current and your terminal is drawing more current than the charging source.
  • Page 43: Battery Error Notification

    • Do not short-circuit a battery or throw it into a fire; it can explode and cause severe personal injury. Do not allow metallic conductive objects to contact battery terminals. • If you observe that the Honeywell battery supplied is physically damaged, please send it to Honeywell International Inc. or an authorized service center for inspection, see...
  • Page 44: Managing Battery Power

    • If you are not sure the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection, see Product Service and Repair on page 13-1. • Excessive discharge can degrade battery performance. Recharge the battery when your terminal indicates low battery power.
  • Page 45: Checking Battery Power

    You can expand the terminal’s memory capacity by installing a microSD or microSDHC memory card. Honeywell recommends the use of Single Level Cell (SLC) industrial grade microSD or microSDHC memory cards with Dolphin terminals for maximum performance and durability. Contact a Honeywell sales representative for additional information on qualified memory card options.
  • Page 46 Installation 1. Press the Power button to place the terminal in Suspend mode. 2. Remove the battery door and battery. 3. Lift the card retention flap for the appropriate socket. SIM Card Retainer Flap Memory Card Retainer Flap 4. Slide the SIM or memory card (contacts facing down) into the appropriate socket, then close the retainer flap.
  • Page 47: Overview

    Using the Scan Image Engine Overview The Dolphin 70e Black terminal houses a compact image engine that instantly reads popular 1D and 2D bar codes and supports omni-directional aiming and decoding for greater flexibility in real-world settings. The image engine can also capture black and white digital images, such as signatures and pictures of damaged inventory.
  • Page 48: Supported Bar Code Symbologies

    5 mil microPDF 5 mil DataMatrix 10 mil DataMatrix 1.52 (3.8) 4.87 (12.3) 3.35 (8.5) 20 mil DataMatrix 1.07 (2.7) 9.66 (24.5) 8.59 (21.8) 10 mil QR 1.50 (3.8) 5.13 (13.0) 3.63 (9.2) 20 mil QR 2.48 (6.3) 9.66 (24.5) 7.18 (18.2) 32 mil Maxicode 1.56 (3.9)
  • Page 49: Decoding

    Decoding The terminal supports image decoding for use in various bar code reading and imaging applications. Full-area imaging provides omni-directional reading of linear and non-linear 1D and 2D bar codes, OCR, signature capture, and picture taking. When reading all bar code types using full-area imaging, a positive read can be obtained from many positions;...
  • Page 50: Capturing Images Using The Imaging Demo

    This is normal. Scan Key Scan Key On all Dolphin 70e Black terminals, the Scan button captures images. File Formats File formats supported for image storage include Bitmap (BMP), JPEG (JPG) and Portable Network Graphics (PNG).
  • Page 51: Taking An Image

    Taking an Image The following steps are basic guidelines for taking images: 1. Touch > Demos > Imaging Demo 2. Point the Dolphin terminal at the object. To preview the image, press and hold the Scan button. Note: The general notification LED above the touch screen illuminates red while the Scan button is pressed. 3.
  • Page 52 4 - 6...
  • Page 53: Chapter 5 - Using The Color Camera

    Using the Color Camera Overview Dolphin 70e Black terminals are equipped with 5.0-Megapixel auto focus cameras to provide easy integration of color picture and video capture into business applications. The camera lens and camera flash are located on the back panel of the terminal.
  • Page 54 Camera Options The Camera Options menu provides access to create customized profiles, adjust audible feedback, modify file preferences, and set caption options. Touch Options > Camera to access the Camera Options menu. The Camera Options screen contains five tabs: Profile, Display, Capture, Caption, and File. Profile Tab Display Tab The profile tab allows you to...
  • Page 55 Capture Tab Caption Tab File Tab 5 - 3...
  • Page 56: Taking A Picture Using The Windows Embedded Handheld 6.5 Camera Tool

    Taking a picture using the Windows Embedded Handheld 6.5 Camera tool 1. Touch > Pictures & Videos > Camera 2. Point the terminal's camera lens at the object you want to capture. Note: The camera lens is located on the back panel of the terminal. 3.
  • Page 57 Options Touch Menu > Options. The Options menu contains four screens: General Screen Slide Show Screen Camera Screen Video Screen 5 - 5...
  • Page 58: Recording Video Using The Windows Embedded Handheld 6.5 Camera Tool

    Recording Video using the Windows Embedded Handheld 6.5 Camera tool 1. Touch > Pictures & Videos > Camera > Menu > Video 2. Point the terminal's camera lens at the object you want to capture. 3. Press the Scan button to start recording. 4.
  • Page 59: Chapter 6 - System Settings

    System Settings Overview Customized settings are available on the System Settings menu. Touch > Settings and the settings screen opens. Icon Description Bluetooth Configure the Bluetooth radio. See Working with the Bluetooth Radio on page 9-1. Home Customize the look and the information displayed on the Home screen. Clock &...
  • Page 60: Clock & Alarms

    Icon Description Connections Establishes network connections settings. See Connections Menu on page 7-1. Personal Customizes buttons, and set SIP options. See Personal Menu on page 6-4. System Adjusts system settings. See System Menu on page 6-9. Clock & Alarms The Clock & Alarms settings can be accessed from the Home screen or the Settings menu. 1.
  • Page 61: Lock

    Lock The Lock settings screen provides access to additional password security features that enable you to prevent an unauthorized person from unlocking the touch screen and accessing the terminal. Select from two password security options: a Strong Alphanumeric Password or a Simple PIN. To add password protection: 1.
  • Page 62: Personal Menu

    . The screen opens displaying the Personal Menu. Icon Description Buttons The Dolphin 70e Black has six programmable buttons (i.e., Right, Left, Home, Scan, Back, and End). Touch the Buttons icon to program the buttons to perform specific tasks. See Buttons on page 6-5.
  • Page 63: Buttons

    Buttons The Dolphin 70e Black has six programmable buttons: Home, Scan, Back, End and the Right and Left side buttons. Use the Buttons setting to reassign the buttons to launch applications or execute commands. Changing Button Assignments 1. Touch > Settings >...
  • Page 64 Additional Functions The Assign a program list also contains the following commands: Command Description <BACK> Returns to the previous screen. <Context Menu> Performs the same function as touch-and-hold to open the context menu for the control. <END> Ends a phone call. <Home>...
  • Page 65 Here, you are performing the same basic process as on the terminal, except that you are using the Explore utility (Windows Explorer) to copy and paste the shortcut. 1. Connect the terminal to the workstation using a Dolphin 70e Black peripheral. 2. Open ActiveSync > Explore and navigate to the program.
  • Page 66: Voice Command

    5. Navigate to the Start Menu folder (Windows > Start Menu > Programs). 6. Right-click on an empty area and select Paste Shortcut. 7. On the terminal, touch the Start menu. 8. Verify that program appears. Voice Command The Voice Command screen provides access to enable or disable voice command for specific applica- tions, adjust how calendar and notification announcements are performed and set up voice activated password protection.
  • Page 67: System Menu

    System Menu The System menu enables you to verify and sometimes alter system parameters. To access the System menu, go to > Settings > System . Touch the appropriate icon to open that system setting. Icon See Page About About on page 6-11.
  • Page 68 Icon See Page Encryption Encryption on page 6-16. Error Error Reporting on page 6-17. Reporting External External GPS on page 6-17. HSM SystemInfo on page 6-17. SystemInfo Managed Managed Programs on page 6-22. Programs Memory Memory on page 6-22. Power Power on page 6-23.
  • Page 69: About

    About The About system settings screen displays specific information about the terminal. Three information screens are available: Version, Device ID, and Copyrights. To access the About system screen, touch > Settings > System . > About The Version Screen Displays the information about the software, operating system, and processor. The Device ID Screen Displays the information the terminal uses to identify itself to other devices.
  • Page 70: Backlight

    Backlight The Backlight system setting enables you to customize backlight functionality for the display and keypad (i.e., Send, Home, Back and End buttons). The settings menu contains three tabs: Dim Backlight, Brightness and Keypad Backlight. To access the Backlight settings, touch >...
  • Page 71 Brightness The Brightness tab determines the backlight intensity of the display when the terminal is in use. The settings customize how the terminal responds to the environmental lighting conditions in which the terminal is being used. Check the "Auto adjust backlight" box to enable automatic adjustment of the backlight intensity depending on the operating environment.
  • Page 72: Battery

    Keypad Backlight The Keypad Backlight tab setting determines when the keypad (i.e., Send, Home, Back and End buttons) backlight is activated. The backlight can be set to turn on with the display, to turn on in dark environments or to stay turned off. Battery The Battery system settings menu contains two tabs: Battery Status and Log Config.
  • Page 73 The Battery Temperature indicates the temperature status of the battery. Battery Chemistry The Battery Chemistry provides the battery type (e.g., LiIon). Battery Serial Number The Battery Serial Number displays the serial number of the authenticated Honeywell battery. Battery Status Tab Log Config Tab 6 - 15...
  • Page 74: Certificates

    Certificates Certificates shows you the certificates that are recognized by the operating system. The Horizontal scroll bar at the top of the screen provides access to the three certificate screens: Intermediate, Personal, and Root. Swipe left or right on the Horizontal scroll or touch the label (e.g., Root or Personal) to access the...
  • Page 75: Error Reporting

    Error Reporting Error Reporting gives you the option of enabling or disabling the error reporting function of Windows Embedded Handheld 6.5. External GPS External GPS determines which port a third-party GPS software application can use to access the GPS receiver. Access Screen Hardware Screen Programs Screen...
  • Page 76: Sip Config

    SIP Config The SIP Config settings screen enables you to configure Session Initiation Protocol (SIP) for Voice Over IP (VoIP) and Telephony communication. To access the SIP Config screens, touch > Settings > System > SIP Config SIP Setting Tab Dial Plan Tab 6 - 18...
  • Page 77: Smart Sensor

    Smart Sensor The Smart Sensor configuration utility enables you to configure the Dolphin’s integrated accelerometer, and motion settings. Touch > Settings > System > Smart Sensor Touch to customize how the terminal responds to motion and object orientation for ease of operation and advanced power management.
  • Page 78 • Motion Detection: Modify the Motion Detection settings to wake the terminal from suspend mode or prevent the terminal from entering suspend mode when motion is detected. Event Track The Event Track tab displays an event log summary of detected free fall events exceeding 2 ft. over 500ms.
  • Page 79: Proximity Sensor Settings

    Proximity Sensor Settings The integrated proximity sensor detects when an object is in close proximity to the entire touch panel display (e.g., a person's face, carrying holster, or tabletop). By default, the proximity sensor automatically turns the display and touch panel off when you hold the terminal near your ear during a phone call. The display and touch panel turn back on when the sensor detects the removal of the object.
  • Page 80: Managed Programs

    Managed Programs The Managed Programs screen lists the installation history of programs on the terminal that are managed by and enrolled to an enterprise domain. Managed Programs is the client-side that works with the server product System Center Mobile Device Manager (MDM). MDM consists of MDM Gateway Server and one or more computers that run MDM Device Management Server;...
  • Page 81: Power

    Data or programs stored in the IPSM are not affected when the operating system is upgraded. Autoinstall programs, for example, are stored in \\IPSM\Honeywell\Autoinstall so that they are always installed after an operating system upgrade or factory reset. Contact a Honeywell technical support representative for more information on how to perform a factory reset. For...
  • Page 82: Regional Settings

    Battery Tab The battery tab displays the power level status of the battery. For detailed information on the main battery, see Battery on page 6-14. Advanced Tab The Advanced tab settings determine power time-outs when running on battery power, external power, or USB power.
  • Page 83: Remove Programs

    If a program is manually removed using the Remove Programs application, the program does not re-install on a hard or soft reset. Note: A program (file) does not automatically install if it is added to the \\IPSM\Honeywell\Autoinstall folder and a hard or soft reset is performed. For information on program installation, see...
  • Page 84: Ril

    The RIL Information screen displays useful statistics for the GSM/CDMA WWAN Voice module and enables you to turn HAC Audio Mode on or off. When HAC Audio mode is enabled, a magnetic/voice coil activates in the terminal earpiece/receiver speaker allowing the terminal to interface with a hearing- aid.
  • Page 85: Task Manager

    Text Size Screen The Text Size screen enables you to perform font scaling within certain views of the: Home screen (only on non-phone devices), Contacts, Calendar, Messaging, and Tasks. Font scaling means that you can increase or decrease the point size of the font on application windows. To change the text size, move the slider toward Smallest or Largest.
  • Page 86 Applications To view the status of the programs running on your mobile computer, touch the Menu button at the bottom of the screen, then touch View > Applications. From the application list, you can: • Touch and hold on an application, then touch Switch To on the pop-up menu. •...
  • Page 87 Processes To view information about the processes running on the mobile computer, touch the Menu button at the bottom of the screen, then touch View > Processes. 6 - 29...
  • Page 88 6 - 30...
  • Page 89: Chapter 7 - Communication

    Communication Connections Menu The Connections system setting provides access to the terminal’s various wireless communication options. Icon Description Beam Enable the terminal to receive incoming beams from devices using Bluetooth wireless technology. See Working with the Bluetooth Radio on page 9-1. Connections Open the Microsoft connections application.
  • Page 90: Microsoft Connections Application

    Icon Description USB to PC Enable advanced wired USB to PC communication via sync software. See Connecting and Synchronizing the Terminal and Workstation on page 7-9. Network Manage Network card settings, search and add wireless networks, and modify advanced Wi-Fi settings (e.g., network notifications and connection time-outs). Cards Microsoft Connections Application The Microsoft Connections application sets up multiple network connections to Internet Service...
  • Page 91 Tasks The Tasks screen enables you to initially configure, and then manage network settings when using a modem. Select an item in this list and then complete the setup screens that follow with the appropriate information for your network. My ISP The links under the My ISP heading enable you to add and manage modem connections to an Internet Service Provider (ISP).
  • Page 92 Modify an Existing Connection The Manage existing connections link appears on the Connections screen under the My ISP heading after at least one network connection has been established. Touch Manage Existing Connections, then follow the setup screens to modify an existing connection. Advanced The Advanced screen enables you to select the default network, dialing rules, and IP address exceptions for modem connections.
  • Page 93: Dolphin Wireless Manager

    Dolphin Wireless Manager The Dolphin Wireless Manager provides a centralized interface that enables and disables all the on- board radios. Each radio has its own configuration program. The Dolphin Wireless Manager also provides shortcuts to the configuration utilities for each radio. To open the Dolphin Wireless Manager do one of the following: 1.
  • Page 94: Enabling The Radios

    Enabling the Radios 1. Open the Dolphin Wireless Manager (see page 7-5). 2. Touch anywhere inside the rectangle of the radio you want to enable. 3. The radio begins activating. 4. When the radio is activated (i.e., transmitting a signal), the Off button changes to ON. Note: If applicable, information about the radio appears in the rectangle.
  • Page 95: Accessing Radio Configuration Utilities

    Menu Option 802.11a/b/g/n Touch WLAN Settings and the Honeywell WLAN Security Supplicant opens. The Honeywell WLAN Security Supplicant User’s Guide is available for download from at www.honeywellaidc.com. Bluetooth Touch Bluetooth Settings and the Bluetooth Settings screen opens. For details, see...
  • Page 96: Usb To Pc

    USB to PC Enable advanced network functionality under the USB to PC connection settings if you are having trouble connecting and synchronizing your terminal with a workstation PC using a wired USB connection and ActiveSync or Windows Device Mobile Center. The advanced network functionality can also be enable to improve transfer speeds when synchronizing large groups of data or copying large files between the terminal and workstation.
  • Page 97: Connecting And Synchronizing The Terminal And Workstation

    When communicating via ActiveSync or WMDC, your terminal is designed to be connected to the host workstation with a communication peripheral sold/manufactured by Honeywell, such as the charge/ communication cable. Use of any peripheral not sold/manufactured by Honeywell may cause damage not covered by the warranty.
  • Page 98 • Windows 98 Second Edition, Windows Me, Windows 2000, Windows NT (4.0 SP6 or higher), Windows XP, Windows Vista, and Windows 7 operating systems. Setting Up the Host Workstation To synchronize data between the terminal and the workstation, ActiveSync (v4.5 or higher) or Windows Mobile Device Center must be configured for same communication type on both the host workstation and the Dolphin terminal.
  • Page 99: Installing Additional Software

    Installing Additional Software Dolphin terminals ship with the operating system, radio drivers, and custom Honeywell software already installed. These are the default programs that install when your terminal first boots up. You can install additional software programs to the terminal provided that the following parameters are met: •...
  • Page 100: Connecting The Terminal To A Wireless Network

    WLAN (802.11a/b/g/n) The Dolphin 70e Black has a 2.4 GHz 802.11b/g/n - 5.0 GHz 802.11a/n WLAN (Wireless Local Area Network) radio. The radio is interoperable with other 802.11a/b/g/n, Wi-Fi compliant products including access points (APs), workstations via PC card adapters, and other wireless portable devices.
  • Page 101: Software Upgrades

    6. The installation wizard for the program begins. 7. Follow the directions on the screen to complete the installation. Software Upgrades Contact a Honeywell technical support representative for information on available software upgrades for your Dolphin terminal, see Customer Support on page 13-1.
  • Page 102 7 - 14...
  • Page 103: Chapter 8 - Working With Wireless Wide Area Networking (Wwan)

    Working with Wireless Wide Area Networking (WWAN) Overview The Dolphin 70e Black has two radio options for WWAN voice and data communications: • a multi-mode (software definable) WWAN radio, which provides support for three band 3.9G UMTS/HSPA+ (850/1900/2100 MHz), quad band GSM/GPRS/EDGE (850/900/1800/1900 MHz), and dual band CDMA/EVDO Rev A - 1xRTT/EVDO (800/1900 Mhz) or •...
  • Page 104: Signal Strength

    For terminals with the GSM WWAN radio: • A penta band antenna that supports 900, 2100 Mhz (UMTS/HSPA) and 850/900/1800/1900 Mhz (GSM/GPRS/EDGE). • A diversity receiver antenna supports 2100Mhz Signal Strength On terminals equipped with a WWAN (voice + data) radio, the signal strength of the WWAN connection is indicated by the number of bars that appear in the signal strength icon in the Title bar at the top of the window.
  • Page 105: Enabling The Wwan Radio

    Enabling the WWAN Radio You can enable or disable the WWAN radio in the Dolphin Wireless Manager (see page 7-5). Note: By default, the WWAN radio is enabled after a factory reset. To enable the WWAN radio: 1. Touch > Settings >...
  • Page 106: Audio Modes

    Audio Modes The Dolphin 70e Black terminal is equipped with speakers on the front and bottom of the terminal and dual microphones that you can use to send and receive audio signals over the GSM network, see Features of the Dolphin 70e Black on page 3-4.
  • Page 107: Accessing Voice Mail

    Displays the network carrier from the SIM card. Displays the most recent calls. Toggles the touch screen Menu keypad On or Off. Dialing Touch the buttons on the dialer window. Sending Calls After the number is dialed, touch Talk or press the Send button Note: The icon indicates that the phone is in use.
  • Page 108: Customizing The Phone

    Customizing the Phone Touch Menu from the Dialer screen to customize options for your phone. View Select View on the Menu to modify the display screen to show Calls and Contacts, All Calls or Speed Dial numbers. Options Select Options on the Menu to customize and view features specific to the network firmware the terminal is configured to use (e.g., GSM/UMTS or CDMA) for voice and data communication.
  • Page 109 Security The Security screen provides access to establish or change your security PIN for phone calls. Check the box next to, “Require a PIN when the phone is used” to enable the PIN security feature. Services For each service, the phone reads settings from the network stored on the SIM card and then displays the available options from the carrier on the screen.
  • Page 110 Network You can find, select, and set your preferred network order from the Network screen. CDMA Options When the WWAN radio is configured to communicate with CDMA networks, the Options menu contains three or four setting widows depending on your network firmware configuration: Sounds, Location Settings, Data Settings (Sprint®...
  • Page 111: Data Communication

    Data Settings The Data Settings screen is available only if the terminal is configured Sprint network communication. Touch the “Provision” button, to initiate an auto-update of your Sprint Vision profile.PC5 Vision. Version Information The Version Information screen displays useful statistics for the CDMA WWAN Voice module including: •...
  • Page 112 3. Enter a name for the connection in the “Enter a name for the connection” box. Select Cellular Line (GPRS) from the drop-down list in the “Select a modem” box. Touch Next. 4. For GSM/UMTS terminal network configuration, the "Access point name" field is automatically filled in with data retrieved from the active SIM card.
  • Page 113: Manual Network Selection (Gsm/Utms)

    9. Touch and hold on the connection name. Select Connect on the popup menu. 10. The network icon in the Title bar indicates the GSM radio is attempting to connect Note: When the device is on a 2G (EDGE/GPRS) network, a data connection failure occurs if the phone is in use for a voice call while attempting a data connection.
  • Page 114: Dolphin Connection Manager

    3. Under Network selection, select Automatic (the default selection) or Manual. a. If you select Manual, the Phone searches for available networks. b. Select a new network and touch OK. c. The Phone registers on the new network and the Network screen appears. d.
  • Page 115 Status Tab The Status tab contains the real time radio status information including: • The power status of the radio (e.g., ON or OFF) • The received signal strength intensity (RSSI) • The radio mode used (e.g., GSM, UMTS, EVDO or 1xRTT) •...
  • Page 116 Profile Tab The Profile tab allows you to see Radio capability information and network statistics including: • Radio Hardware and Software versions • Radio and SIM identification numbers • Serving network connection type and state • Available radio interfaces for the current serving network Hyper Roaming Tab The Hyper Roaming tab allows you to turn roaming capabilities on or off and customize network and connection settings includ-...
  • Page 117: Chapter 9 - Working With The Bluetooth Radio

    Working with the Bluetooth Radio Enabling the Bluetooth Radio You enable the Bluetooth radio in the Dolphin Wireless Manager (see page 7-5). 1. Touch > Settings > Connections > Dolphin Wireless Manager 2. Touch anywhere inside the Bluetooth rectangle to begin activation of the Bluetooth radio. 3.
  • Page 118: Pairing And Trusted Devices

    Pairing and Trusted Devices The terminal supports pairing. Pairing happens during the general connection setup. Paired devices are "trusted" devices. This means that there is unrestricted access to all services (including services that require authorization and authentication). A connection can exclude pairing. A device that is connected to the terminal but not paired with it is considered an untrusted device.
  • Page 119 4. Select a device from the list and touch Next. The types of devices in the vicinity of the radio appear in the list of discovered devices. 5. You are prompted to enter a passcode. • If the device has a specific passcode, enter it in the Passcode field and touch Next. When attempting to connect to a printer or headset with Bluetooth capabilities, the passcode may default to either 1111 or 0000.
  • Page 120 8. When the connection is complete, a list of matching and supported services on the device appears. Only the services that are mutually supported on both devices appear in the Partnership Settings window. 9. Select the services you want to use and touch Save. The services on the new devices have to be selected or the pairing won’t include those services, even though the devices are paired.
  • Page 121: Transferring Files Using Beam File

    Transferring Files using Beam File Before attempting to transfer files, make sure the receiving Bluetooth device is in range, set to be discov- erable by other devices, and set to receive incoming beams. 1. Touch > File Explorer. 2. Navigate to the file you want to transfer. 3.
  • Page 122: Making The Terminal Discoverable

    3. Select “Make this device visible to other devices” and touch OK. Enabling the Terminal to Receive Incoming Beams By default, the Dolphin 70e Black terminal is not configured to receive incoming beams from other devices attempting file transfers via the Beam File command. Before initiating a file transfer from another device follow the steps below to enable Beam reception on your Dolphin terminal.
  • Page 123: Chapter 10 - Working With Gps

    Working with GPS Overview The Dolphin 70e Black terminal contains an integrated GPS module that allows location tracking of workers and vehicles, providing better utilization of field assets. Optional mapping and navigation software provides turn-by-turn driving directions and location information.
  • Page 124: Com7

    COM7 COM Port 7 can be set to the following baud rates: • 4800 • 9600 (Default baud rate. Recommended for optimal performance.) • 19200 • 38400 Other baud rates are not possible. The baud rate selected on COM7 is the actual baud rate with which the GPS communicates.
  • Page 125: Chapter 11 - Dolphin 70E Black Homebase Device (Model 70E-Hb)

    Guidelines for Battery Pack Use and Disposal on page 3-13. We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty. Communications Reliable data communications at speeds of up to 480 Mbps can be transmitted by the base through the Hi-Speed USB port.
  • Page 126: Convenient Storage

    This means that one base can charge two battery packs: the one installed in the terminal and a spare. We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell peripherals, cables, or power adapters may cause damage not covered by the warranty.
  • Page 127: Parts And Functions

    Parts and Functions Front Panel Auxiliary Battery Well Terminal Well COMM LED AUX Battery LED Dock LED Terminal Well Place the terminal in this well to communicate with a host device, power the terminal, and charge the installed battery pack. The base completely charges the main battery in a Dolphin terminal in 4 hours for the standard battery or 6 hours for the extended battery.
  • Page 128: Back Panel

    Dock LED Indicates if a terminal is docked properly in the base. This color means… Blue The terminal is properly seated in the base. COMM LED This is the communication LED. It indicates the status of data transfer between the Dolphin terminal and the host device.
  • Page 129: Bottom Panel

    The power adapter included with the base, converts the voltage from the AC power source to 12 Volts DC. Use only a UL listed power supply, which has been qualified by Honeywell with output rated at 12VDC and 3 amps with the device. The operating temperature range is -10° to 50°C (14°...
  • Page 130: Charging The Main Battery

    Checking Battery Power on page 3-15. We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty. Charging a Spare Battery in the Auxiliary Battery Well The auxiliary battery well located on the back of the base charges a spare battery independently of the terminal well.
  • Page 131: Communication

    Communication Dolphin terminals support USB communications out of the box. The base also supports USB communi- cations via the USB port located on the back. The base acts as a USB device by interfacing the USB signals of the Dolphin terminal to the USB of the host workstation. Using a standard USB cable, the base’s USB interface allows the Dolphin terminal to communicate with a workstation.
  • Page 132 2. Then, using the appropriate nuts and bolts, secure the DIN rail to the desk or flat surface. 11 - 8...
  • Page 133: Chapter 12 - Dolphin 70E Black Chargebase Device (Model 70E-Cb)

    Dolphin 70e Black ChargeBase Device (Model 70e-CB) Overview The Dolphin 70e Black ChargeBase is a 4-slot charging cradle that can power four Dolphin terminals, and charge their main batteries in 4 hours for the standard battery or 6 hours for the extended battery.
  • Page 134: Dimensions

    Dimensions 59.75 mm [2.35 inches] 427.11 mm 98.8 mm [16.80 inches] [3.89 inches] Weight ChargeBase weight: 1.1kg [2.43 lbs.] Parts and Functions Front Panel Terminal Wells (Qty. 4) Dock LED (Qty. 4) Terminal Wells The base contains four terminal wells, which offer independent battery charging for each docked terminal.
  • Page 135: Back Panel

    AC power source to 12 volts DC. Use only a UL Listed power supply, which has been qualified by Honeywell with output rated at 12VDC and 5 amps with the device. The operating temperature range is -10° to 50°C (14° to 122°F).
  • Page 136: Connecting Power To The Chargebase

    Honeywell recommends that you leave the ChargeBase connected to its power source at all times, so that it is always ready to use. We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell peripherals, cables, or power adapters may cause damage not covered by the warranty.
  • Page 137: Mounting The Chargebase

    Mounting the ChargeBase This base should be mounted to a dry, stable surface. When choosing a location, always bear in mind that: • The mounting location must allow users easy access to the power connector. • The base should be oriented so that users can easily see the LEDs. Bottom Panel DIN Rail Slot Rubber Feet, Qty.
  • Page 138 2. Turn the base and DIN Rail right side up. 3. Then, using the appropriate nuts and bolts, secure the DIN Rail to a stable, flat horizontal surface. 12 - 6...
  • Page 139: Chapter 13 - Customer Support

    If your mobile device has a touch screen display, please note that a touch screen responds best to a light touch from the pad of your finger or a Honeywell approved stylus. Using excessive force or a metallic object when pressing on the touch-screen may cause damage to the tempered glass surface and may not be covered by the product's warranty.
  • Page 140 • The duration of the limited warranty for terminals with an integrated imager is one year. • The duration of the limited warranty for touch screens is one year. • The duration of the limited warranty for the Dolphin 70e Black HomeBase device, and Dolphin 70e Black ChargeBase device, is one year.
  • Page 141: How To Extend Your Warranty

    How to Extend Your Warranty Honeywell International Inc. offers a variety of service plans on our hardware products. These agree- ments offer continued coverage for your equipment after the initial warranty expires. For more infor- mation, contact your Sales Representative, Customer Account Representative, or Product Service Marketing Manager from Honeywell International Inc., or your Authorized Reseller.
  • Page 142 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com 70E-WEH-UG Rev A 6/13...

Table of Contents