Advertisement
Quick Links
VEC1376RL_Manual_030405
3/4/05
6:11 PM
Page 4
If you suspect the bulb is burned out, check if the lamp will operate when powered
using the AC charger/adapter. If Low brightness is selected and the bulb won't
light, it probably needs to be replaced.
You will need a new replacement bulb (Vector part VEC193)*. The globe assembly
that contains the bulb is in two halves. To remove the top half of the globe, the three
flanges under the shade must be unscrewed from the three supports that fasten the
shade to the globe. They can be removed without tools.
SHADE
1. Make sure the lamp is turned OFF.
2. Reach under the shade and unscrew (counterclockwise) all three flanges until they
slide down the supports.
3. Lift off the shade and top half of the globe and set them aside.
4. Using a cloth, grasp the bulb, pull it straight up and dispose of it properly.
5. Using a clean cloth, remove the bulb from its package. Avoid touching it with
bare skin.
6. Note the two pins and the small holes on the bulb socket.
7. Insert the two pins of the bulb into the socket and make sure they are fully seated.
8. Briefly turn on the lamp to test operation of the new bulb.
9. Locate the shade and top half of the globe and reattach the flange threads (one
at a time) in the shade`assembly.
10. Continue to tighten (clockwise) so the globe is secure. DO NOT OVERTIGHTEN!
• A high quality, G4 base, 6 volt, 10-watt bulb may be used if a VEC193 bulb is not available.
SPECIFICATIONS
Power:
AC charger/adapter 110 volt AC to
7.2 volt DC 1650 mA.
UL Listed class 2 power supply
Battery:
VEC1996 volt 6 Amp Hour, sealed lead-acid
Bulb:
VEC193 (See Note)
Weight:
4.75 lbs (2.15 kg)
Height:
13.75 in (34.9 cm)
Shade Diameter:
9.25 in (23.5 cm)
Base Width/Depth:
6.0 in (15.24 cm)
© 2005 VECTOR MANUFACTURING, Ltd.
FT. LAUDERDALE, FL 33312
4
SUPPORTS
FLANGE
IMPORTANT SAFETY INFORMATION, SAVE THESE INSTRUCTIONS
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND
THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS
PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.
MADE IN CHINA
Indoor/Outdoor
RECHARGEABLE LAMP
USER'S MANUAL
& WARRANTY INFORMATION
4140 S.W. 28th Way, Ft. Lauderdale, FL 33312
Toll Free: (866) 584-5504
www.vectormfg.com
VEC1376RL
Advertisement
Related Manuals for Vector RECHARGEABLE LAMP
Summary of Contents for Vector RECHARGEABLE LAMP
- Page 1 AC charger/adapter. If Low brightness is selected and the bulb won't light, it probably needs to be replaced. You will need a new replacement bulb (Vector part VEC193)*. The globe assembly that contains the bulb is in two halves. To remove the top half of the globe, the three flanges under the shade must be unscrewed from the three supports that fasten the shade to the globe.
- Page 2 2. Do not attempt to operate or charge if the lamp or charging adapter is damaged. This Vector Manufacturing, Ltd. product is warranted, to the original purchaser only, to be free of defects in 3. Do not immerse the lamp in water. See the Care and Maintenance section on page 2 for cleaning materials and workmanship for one year from the date of purchase without additional charge.
- Page 3 VEC1376RL_Manual_030405 3/4/05 6:11 PM Page iv INTRODUCTION TABLE OF CONTENTS Thank you for purchasing the VEC1376RL Indoor/Outdoor Rechargeable Introduction ........... 1 Lamp.
- Page 4 Adapter/Charger from the AC outlet. You will need a 6 volt, 6 amp/hour • Plug the AC/DC power adapter/charger’s plug into a powered 120 volt AC wall replacement battery (Vector part# VEC199) and a small Phillips screwdriver. The outlet. procedure to replace the battery is as follows: Make sure that the AC charger/adapter is powered from the correct AC source.