LG DLE2301W Service Manual
  1. Manuals
  2. Brands
  3. LG Manuals
  4. Dryer
  5. DLE2301W
  6. Service manual

LG DLE2301W Service Manual

Electric & gas dryer
Hide thumbs Also See for DLE2301W:
Table of Contents

Advertisement

Quick Links

See also: User Manual and Installation Instructions
ELECTRIC & GAS DRYER
SERVICE MANUAL
CAUTION
READ THIS MANUAL CAREFULLY IN ORDER TO
PROPERLY DIAGNOSE PROBLEMS AND TO SAFELY
PROVIDE QUALITY SERVICE ON THESE DRYERS.
MODEL : DLE2301W / DLG2302W
DLE2301R / DLG2302R
U.S.A. Website: http://us.lgservice.com
Canadian Website: http://lg.ca

Advertisement

Table of Contents
loading

Related Manuals for LG DLE2301W

Summary of Contents for LG DLE2301W

  • Page 1 U.S.A. Website: http://us.lgservice.com Canadian Website: http://lg.ca ELECTRIC & GAS DRYER SERVICE MANUAL CAUTION READ THIS MANUAL CAREFULLY IN ORDER TO PROPERLY DIAGNOSE PROBLEMS AND TO SAFELY PROVIDE QUALITY SERVICE ON THESE DRYERS. MODEL : DLE2301W / DLG2302W DLE2301R / DLG2302R...
  • Page 2 MAR. 2007 PRINTED IN KOREA P/No.:3828EL3005L...

  • Page 3: What To Do If You Smell Gas

    IMPORTANT SAFETY NOTICE The information in this service guide is intended for use by individuals possessing skill and experience in electrical, electronic, and mechanical appliance repair. Any attempt to repair a major appliance may result in personal injury and property damage. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use.

  • Page 4: Table Of Contents

    CONTENTS 1. SPECIFICATIONS ........................4 2. FEATURES AND BENEFITS ....................6 3. INSTALLATION INSTRUCTIONS ................... 6 4. DRYER CYCLE PROCESS ..................... 13 5. COMPONENT TESTING INFORMATION ................14 6. MOTOR DIAGRAM AND SCHEMATIC..................17 7. CONTROL LAYOUT ......................18 8. WIRING DIAGRAM ......................19 9. DIAGNOSTIC TEST ......................20 9-1.

  • Page 5: Specifications

    SPECIFICATIONS I Name: Electric and Gas Dryer I Power supply: Please refer to the rating label regarding detailed information. I Size: 27 X 29.9 X 38.7 (inch) I Dryer capacity: IEC 7.3 cu.ft. I Weight: 126(Ibs) Specifications are subject to change by manufacturer. I ACCESSORIES Dryer rack (1 each) Stacking kit (1 each)
  • Page 6 DLE2301W DLE2301R REMARK ITEM DLG2302W DLG2302R CANDY APPLY RED Color Blue Whit Material & Top Plate Porcelain Finish Door Trim Chromate POWER SUPPLY 120V/240V 60Hz (26A) MOTOR 250W (4.5A) AC 120V ELECTRICITY HEATER 5400W (22.5A) AC 240V (ELECTRIC MODEL) CONSUMPTION...

  • Page 7: Features And Benefits

    FEATURES AND BENEFITS INSTALLATION INSTRUCTIONS Dryer Rack Installation Instructions Put the dryer rack into Check and be sure that the Open the door. the drum front of the rack is properly Hold the dryer rack seated behind the lint filter. with both hands.

  • Page 8: Stacking Kit Installation Instructions

    Stacking Kit Installation Instructions To ensure safe and secure installation, please observe the instructions below. Secure the side bracket to the washer with WARNING a screw on the back of the bracket. Repeat Steps 2, 3, & 4 for the other side. Do not attempt this alone! At least two people are required to lift and position the dryer on top of a washing...
  • Page 9 Pedestal Installation Instructions Attach the double-faced tape of the bracket to the After removing the protective covering from the dryer as shown so the bent parts of the brackets adhesive surface, align the screw holes in the brackets with the matching holes in the pedestal align with the edge and can be attached to the base and press and press the brackets against pedestal with screws.
  • Page 10 Electric Dryer Only Review the following options to determine the appropriate electrical connection for your home: 4-wire receptacle 4-wire connection : Direct wire (NEMA type14-30R) Important : Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations, (2) mobile homes, and (3) recreational vehicles, and Use the instructions under option 1 if your home (4) areas where local codes prohibit grounding through homehas a 4-wire receptacle (NEMA type 14-30R).
  • Page 11 3-wire connection : Direct wire Option 1: 4-wire connection with a Power supply cord. Important : Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations, • lf your local codes or ordinances do not allow the (2) mobile homes, and (3) recreational vehicles, and use of a 3 wire connection, or you are installing (4) areas where local codes prohibit grounding through your dryer in a mobile home, you must use a 4-...
  • Page 12 Option 3: Optional 3-wire Option 2: 3-Wire Connection with connection. a Power Supply Cord • If your local codes or ordinances do not allow the lf your local codes or ordinances permit the connection of a frame-grounding conductor to the connection of a frame-grounding conductor to the neutral wire, use the instructions under this neutral wire, use these instructions.

  • Page 13: Connect Gas Supply Pipe (Gas Dryer Only)

    3-2. Connect Gas Supply Pipe (Gas Dryer ONLY) For further assistance, refer to section on Gas Requirements. 1. Make certain your dryer is equipped for use with the 3. Connect to gas supply pipe using a new flexible type of gas in your laundry room. Dryer is equipped stainless steel connector.

  • Page 14: Dryer Cycle Process

    DRYER CYCLE PROCESS Default Conditions of operation and termination Drying Cooling Wrinkle care Cycle Temp- Display erature time Electro- Temp- Default Temp- Level Time sensor Control time Control** 68 ± 4°C 47 ± 5°C HEAVY DUTY HIGH (Normal) 54min Saturation (5min) COTTON/ 66 ±...

  • Page 15: Component Testing Information

    COMPONENT TESTING INFORMATION When checking the Component, be sure to turn the power off, and do voltage discharge sufficiently. CAUTION Component Test Procedure Check result Remark 1. Thermal cut off Measure resistance of terminal If thermal fuse is open must •...
  • Page 16 Component Test Procedure Check result Remark 7. Heater Measure resistance of the • Electric type following terminal Terminal: 1 (COM) - 2 Resistance value: 10Ω Terminal: 1 (COM) - 3 Resistance value: 10Ω Terminal: 2 - 3 Resistance value: 20Ω 8.
  • Page 17 Component Test Procedure Check result Remark 13. Outlet Thermostat Measure resistance of terminal • Gas type (Auto reset) to terminal • Gas funnel ∞ Open at 203 ± 7°F (95 ± 5°C) Resistance value Continuity < 1Ω Close at 158 ± 9°F (70 ± 5°C) •...

  • Page 18: Motor Diagram And Schematic

    MOTOR DIAGRAM AND SCHEMATIC When checking Component, be sure to turn Power off, then do voltage discharge sufficiently. NOTE Contact On / Off by Centrifugal Switch STOP MODE RUN MODE (When Motor does not operate) (Motor operates) Centrifugal switch Centrifugal switch (Pull Drive forward)

  • Page 19: Control Layout

    CONTROL LAY - OUT PWB ASSEMBLY DISPLAY LAYOUT 7-SEG Display in QC-Test MODE 7-SEG MAIN P/NO DISPLAY P/NO NOTE DISPLAY EBR36858801 18:88 Electric, NEXT(D) LED, North America EBR36858901 Gas, NEXT(D) LED, North America EBR36858802 18:88 PWB ASSEMBLY LAYOUT Main PWB Asm (NEXT DRYER) MODEL AS DIAGNOSTIC TEST STEAM STEAM...

  • Page 20: Wiring Diagram

    WIRING DIAGRAM ELECTRIC DRYER WIRING DIAGRAM ELECTRONIC CONTROL BLACK WHITE TAB RELAY TAB RELAY TRANS BLACK WHITE LAMP BELT BLUE SWITCH YELLOW HEATER GRAY 7 10 MOTOR MOISTURE THERMISTOR OVERLOAD SENSOR PROTECTOR DOOR SWITCH BLOWER THERMOSTAT WHITE SAFETY THERMOSTAT GAS DRYER WIRING DIAGRAM ELECTRONIC CONTROL POWER CORD BLACK...

  • Page 21: Diagnostic Test

    DIAGNOSTIC TEST 1. This TEST should be used for Factory test /Service test. Do not use this DIAGNOSTIC TEST other than specified. 2. Activating the Heater manually with the Door open may trip the Thermostat attached to the Heater, therefore do not activate it manually.

  • Page 22: Test 1 120V Ac Electrical Supply

    Test 1 120V AC Electrical supply When measuring power, be sure to wear insulated gloves, to and avoid an Caution electric shock. Trouble Symptom No power was applied to Controller. (LED,LCD Display off) Measurement Condition With Dryer Power On; Connector linked to Controller. •...

  • Page 23: Power Connection

    Caution When measuring power, be sure to wear insulated gloves, to and avoid an electric shock. Trouble Symptom Check the Tab Relays Connection properly. Measurement Condition With Dryer Power On; Connector linked to Controller. 1.Power Connection < Table1 > : Connection of the Tab Relay with Heater (Elec) Tab Relay 1 Tab Relay 2 Heater 1 Heater 2...
  • Page 24 < Table 2 > : Connection of Tab Relay with PCB ASSEMBLY (Gas) Remark Color Harness Check the Matching color Between Harness wire and Tab Relay. Black Connector Housing (Black Housing – Black Tab Relay) Connector Housing Tap relay 1 3.

  • Page 25: Test 2 Thermistor Test

    Test 2 Thermistor Test --- Measure with Power Off Before measuring resistance, be sure to turn Power off, and do voltage discharge. Caution (When discharging, contact the metal plug of Power cord with the Ground.) During Diagnostic Test, tE1 and tE2 Error occur. Trouble Symptom During operation, Heater would not turn off, or remains on.

  • Page 26: Test 3 Motor Test

    Test 3 Motor test Before measuring resistance, be sure to turn Power off, and do voltage discharge. Caution (When discharging, contact the metal plug of Power cord with earth line.) Trouble Symptom Drum will not rotate; No fan will function; No Heater will work. Measurement Condition Turn the Dryer’s Power Off, then measure resistance.

  • Page 27: Test 4 Moisture Sensor

    Test 4 Moisture sensor Before measuring resistance, be sure to turn Power off, and do voltage discharge. Caution (When discharging, contact the metal plug of Power cord with earth line.) Trouble Symptom Degree of dryness does not match with Dry Level. Measurement Condition Turn the Dryer’s Power Off, then measure resistance.

  • Page 28: Test 5 Door Switch Test

    Test 5 Door switch test Before measuring resistance, be sure to turn Power off, and do voltage discharge. Caution (When discharging, contact the metal plug of Power cord with earth line.) Door Opening is not sensed.(During operation, when opening Door, Drum motor and Trouble Symptom Heater run continuously) Door Close is not sensed.
  • Page 29 Test 6 Heater switch test - Electric Type Before measuring resistance, be sure to turn Power off, and do voltage discharge. Caution (When discharging, contact the metal plug of Power cord with earth line.) While operating, Heating will not work. Trouble Symptom Drying time takes longer.
  • Page 30 Test 7 GAS Valve test - Gas Type Caution When measuring power, be sure to wear insulated gloves, to avoid electric shock. While operating, Heating will not work. Trouble Symptom Drying time takes longer. Measurement Condition With dryer power on Power On &...

  • Page 31: Test 8 Semi-Conductor

    Test 8 Semi Conductor Before measuring resistance, be sure to turn Power off, and do voltage discharge. Caution (When discharging, contact the metal plug of Power cord with earth line.) Degree of Resistance is not in 300°æ30 Ω Trouble Symptom Measurement Condition Turn the Dryer’s Power Off, then measure resistance.

  • Page 32: Change Gas Setting (Natural Gas, Propane Gas)

    CHANGE GAS SETTING (NATURAL GAS, PROPANE GAS) Changing orifices and gas valve adjustments improperly can result in an Warning explosion and/or fire. Conversion must be made by a qualified technician. Initially , Natural Gas mode is set. Propane Gas Orifice is on sale as a Service Part to authorized servicers only.
  • Page 33 GAS VALVE FLOW START KEY PUSH VALVE 1 ON (VALVE 2 OFF) IGNITER ON IGNITER TEMPERATURE ABOUT FLAME DETECT OPEN VALVE 2 ON GAS IGNITION FLAME DETECT CLOSE DRYING VALVE 2 OFF GAS IGNITION GAS VALVE STRUCTURE Adjustment Screw START VALVE 1 IGNITER FLAME...

  • Page 34: Disassembly Instructions

    DISASSEMBLY INSTRUCTIONS ✽ Disassemble and repair the unit only after pulling out power plug from the outlet. TOP PLATE WARNING ! When you disassemble the top plate, be sure to take gloves and careful plate’s edge. Failure to do so can cause serious injury.
  • Page 35 CONTROL PANEL ASSEMBLY WARNING ! When you disassemble the control panel, be sure to take gloves and careful panel frame’s edge. Failure to do so can cause serious injury. Remove 2 screws on the control panel frame. Disconnect the connectors. Pull the control panel assembly upward and then forward.
  • Page 36 COVER CABINET WARNING ! When you disassemble the door switch connector, be sure to take gloves and careful cabinet edge. Failure to do so can cause serious injury. Disassemble the top plate. Disassemble the control panel assembly. Disassemble the door assembly. Remove 2 screws.

  • Page 37: Drum Assembly

    TUB DRUM [FRONT] WARNING ! When you disassemble the lamp connector, be sure to take gloves and careful cabinet edge. Failure to do so can cause serious injury. Disassemble the top plate. Remove Cover Cabinet. Disconnect the door lamp and electrode sensor connector.
  • Page 38 DRYER EXHAUST CHANGE WARNING ! When you disassemble and install ventilation, be sure to take gloves and careful exhaust edge. Failure to do so can cause serious injury. Remove a screw and the exhaust duct. 2-1. Detach and remove a knockout at the botton, left or right side as desired.
  • Page 39 Remove the filter. Remove 3 screws. Remove the Cover Grid. Disconnect the electrode sensor. Disassemble the top plate. Remove the Cabinet Cover and Tub Drum [Front]. Remove the Drum assembly. Remove 2 screws and cover (Air guide). Remove the bolt and washer. Remove the fan.
  • Page 40 Disassemble the top plate. Remove the Cover Cabinet. Remove the filter and 2 screws. Remove the air duct. Disassemble the top plate. Remove the Cover Cabinet and Tub Drum [Front]. Remove the Drum assembly and Tub Drum [Rear]. Disconnect the Air duct from the Tub Drum [Front]. Remove the roller from the Tub Drum [Front] and Tub Drum [Rear].

  • Page 41: Exploded View

    EXPLODED VIEW 12-1. Control Panel & Plate Assembly A211 A210 A130 A120 A140 A110...

  • Page 42: Cabinet & Door Assembly

    12-2. Cabinet & Door Assembly A700 A800 A570 A560 A390 A131 A600 A330 A300 A500 A320 A305 A530 A510 A520 A310 A525 A430 A540 A400 A450 A410 A460 A420...
  • Page 43 12-3-1. Drum & Motor Assembly: Electric Type F200 K400 K120 K140 K100 K130 K250 K251 K310 K330 K320 K340 K222 K221 K620 K230 K210 K250 K350 K360 K610 K550 K560 K251 K240 K530 K515 K640 K651 F140 K510 K520 K540 F130 F110 K650...

This manual is also suitable for:

Dlg2302wDle2301rDlg2302r

Table of Contents