Page 2
AMI is a registered trademark of American Megatrends Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Intel® Ivy Bridge (Sandy Bridge) DC/QC Processor are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation.
The Q77 platform is made with 22 nanometer technology that supports Intel’s first processor architecture to unite the CPU and the graphics core on the transistor level. The MB970 ATX board utilizes the dramatic increase in performance provided this Intel’s latest cutting-edge technology.
INTRODUCTION Checklist Your MB970 package should include the items listed below. The MB970 ATX motherboard This User’s Manual 1 CD containing chipset drivers and flash memory utility Serial ATA cable MB970 User’s Manual...
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the MB970 in order to set up a workable system. The topics covered are: Installing the CPU......Fehler! Textmarke nicht definiert. Installing the Memory....Fehler! Textmarke nicht definiert.
INSTALLATIONS Installing the CPU The MB970 board supports an LGA1155 Socket (shown below) for Intel Sandy Bridge processors. To install the CPU, unlock first the socket by pressing the lever sideways, then lift it up to a 90-degree. Then, position the CPU above the socket such that the CPU corner aligns with the gold triangle matching the socket corner with a small triangle.
INSTALLATIONS Installing the Memory The MB970 board supports four DDR3 memory socket for a maximum total memory of 32GB in DDR3 DIMM memory type. Installing and Removing Memory Modules To install the DDR3 modules, locate the memory slot on the board and perform the following steps: 1.
INSTALLATIONS Setting the Jumpers Jumpers are used on MB970 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on MB970 and their respective functions.
SHIELD 0/5 DATA 4+ DATA 5- DDC CLOCK DATA 5+ DDC DATA SHIELD CLK CLOCK - DATA 1- CLOCK + DATA 1+ SHIELD 1/3 DATA 3- DATA 3+ DDC POWER A GROUND2 A GROUND 1 A GROUND3 MB970 User’s Manual...
J19, J20: COM3, COM4 RS232 Serial Ports Signal Name Pin # Pin # Signal Name DCD# DSR# SIN# RTS# SOUT CTS# DTR# CN7: Gigabit LAN (Intel 82579LM) + USB 2/3 CN6: Gigabit LAN (Intel 82583V) + USB 0/1 CN4: HD Audio Connector MB970 User’s Manual...
This connector supplies the CPU operating voltage. Pin # Signal Name Ground Ground +12V +12V J4: ISA Slot (shared with PCI1) J19, J20: COM3, COM4 RS232 Serial Ports Signal Name Pin # Pin # Signal Name DCD# DSR# SIN# RTS# SOUT CTS# DTR# MB970 User’s Manual...
BIOS Introduction The BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
F3: Optimized Default F4: Save ESC: Exit System Language Choose the system default language. System Date Set the Date. Use Tab to switch between Data elements. System Time Set the Time. Use Tab to switch between Data elements. MB970 User’s Manual...
Disabled F4: Save ESC: Exit SERR# Generation Disabled ► PCI Express Settings Above 4G Decoding Enables or Disables 64bit capable devices to be decoded in above 4G address space (only if system supports 64 bit PCI decoding). MB970 User’s Manual...
Keep Link ON Relaxed Ordering Enables or disables PCI Express Device Relaxed Ordering. Extended Tag If ENABLED allows device to use 8-bit Tag field as a requester. No Snoop Enables or disables PCI Express Device No Snoop option. MB970 User’s Manual...
Page 29
Defines number of Microseconds software will wait before polling ‘Link Training’ bit in Link Status register. Value range from 10 to 1000 uS. Unpopulated Links In order to save power, software will disable unpopulated PCI Express links, if this option set to ‘Disable Link’. MB970 User’s Manual...
This option may be not effective with some OS. ACPI Sleep State Select ACPI sleep state the system will enter, when the SUSPEND button is pressed. Lock Legacy Resources Enabled or Disabled Lock of Legacy Resources. S3 Video Repost Enable or disable S3 Video Repost. MB970 User’s Manual...
Disables TPM support. O.S. will not show TPM. Reset of platform is required. Security Device Support Enables or disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. MB970 User’s Manual...
This section shows the CPU configuration parameters. Aptio Setup Utility Advanced Main Chipset Boot Security Save & Exit CPU Configuration Intel® Core ™ i7-3770 CPU @ 3.40GHz Processor Stepping 306a8 Microcode Revision Max CPU Speed 3400 MHz Min CPU Speed 1600 MHz CPU Speed...
Unknown F4: Save ESC: Exit SATA Port4 Empty Software Preserve Unknown SATA Port5 Empty Software Preserve Unknown SATA Controller(s) Enable / Disable Serial ATA Controller. SATA Mode Selection (1) IDE Mode. (2) AHCI Mode. (3) RAID Mode. MB970 User’s Manual...
Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit ISmart Controller Setup the power on time for the system. Schedule Slot 1 / 2 Setup the hour/minute for system power on. MB970 User’s Manual...
Page 35
Set timer to wait before sending ASF_GET_BOOT_OPTIONS. Activate Remote Assistance Process Trigger CIRA boot. PET Progress User can Enable/Disable PET Events progress to receive PET events or not. Watchdog Timer This configuration is supported only with MB970VF (with iAMT function). Enable/Disable Watchdog Timer. MB970 User’s Manual...
DISABLE option will keep USB devices available only for EFI applications. USB3.0 Support Enable/Disable USB3.0 (XHCI) Controller support. XHCI Hand-off This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. MB970 User’s Manual...
Page 37
F4: Save ESC: Exit USB3.0 Port0/1 POWER Management Enabled USB3.0 Port2/3 POWER Management Enabled Serial Port Configuration Set Parameters of Serial Ports. User can Enable/Disable the serial port and Select an optimal settings for the Super IO Device. MB970 User’s Manual...
Page 38
PC health status. Fan1/Fan2 Smart Fan Control This field enables or disables the smart fan feature. At a certain temperature, the fan starts turning. Once the temperature drops to a certain level, it stops turning again. MB970 User’s Manual...
This section allows you to configure the North Bridge Chipset. Aptio Setup Utility Chipset Main Advanced Boot Security Save & Exit Intel PCH RC Version 1.1.0.0 Intel PCH SKU Name Intel PCH Rev ID O4/C1 ► PCI Express Configuration ► USB Configuration ► PCH Azalia Configuration...
Enable or disable PCI Express Clock Gating for each root port. DMI Link ASPM Control The control of Active State Power Management on both NB side and SB side of the DMI link. PCIe-USB Glitch W/A PCIe-USB Glitch W/A for bad USB device(s) connected behind PCIE/PEG port. MB970 User’s Manual...
Enable or disable xHCI Maximum Primary Stream Array Size. EHCI1/2 Control the USAB EHCI (USB 2.0) functions. One EHCI controller must always be enabled. USB Ports Per-Port Disable Control Control each of the USB ports (0~13) disabling. MB970 User’s Manual...
F3: Optimized Default ► Memory Configuration F4: Save ESC: Exit VT-d Check to enable VT-d function on MCH. Enable NB CRID Enable or disable NB CRID WorkAround. C-State Pre-Wake Controls C-State Pre-Wake feature for ARAT, in SSKPD[57]. MB970 User’s Manual...
Page 44
Select the Video Device that will be activated during POST. This has no effect if external graphics present. Secondary booty display selection will appear based on your selection. VGA modes will be supported only on primary display. MB970 User’s Manual...
2048 MB (DDR3) Enter: Select CAS Latency (tCL) Change Field Minimum delay time F1: General Help CAS to RAS (tRCDmin) F2: Previous Values Row Precharge (tRPmin) F3: Optimized Default Active to Precharge (tRASmin) F4: Save ESC: Exit MB970 User’s Manual...
UPON REQUEST – GA20 can be disabled using BIOS services. ALWAYS – do not allow disabling GA20; this option is useful when any RT code is executed above 1MB. Option ROM Messages Set display mode for Option ROM. Options are Force BIOS and Keep Current. MB970 User’s Manual...
Controls the execution of UEFI and Legacy Storage OpROM. Launch Video OpROM policy Controls the execution of UEFI and Legacy Video OpROM. Other PCI device ROM priority For PCI devices other than Network, Mass storage or Video defines which OpROM to launch. MB970 User’s Manual...
Change Field F1: General Help in the following range: Minimum length F2: Previous Values F3: Optimized Default Maximum length F4: Save ESC: Exit Administrator Password User Password Administrator Password Set Setup Administrator Password. User Password Set User Password. MB970 User’s Manual...
Page 49
Discard Changes done so far to any of the setup options. Restore Defaults Restore/Load Defaults values for all the setup options. Save as User Defaults Save the changes done so far as User Defaults. Restore User Defaults Restore the User Defaults to all the setup options. MB970 User’s Manual...
LAN Drivers Installation ..............55 Intel® Management Engine Interface..........59 Intel® USB 3.0 Drivers ............... 62 IMPORTANT NOTE: After installing your Windows operating system, you must install first the Intel Chipset Software Installation Utility before proceeding with the drivers installation. MB970 User’s Manual...
Plug & Play INF support for Intel chipset components. Follow the instructions below to complete the installation. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) 7 Series Chipset Drivers. 2. Click Intel(R) Chipset Software Installation Utility.
Page 52
DRIVER INSTALLATION 3. When the Welcome screen to the Intel® Chipset Device Software appears, click Next to continue. 4. Click Yes to accept the software license agreement and proceed with the installation process. MB970 User’s Manual...
Page 53
DRIVERS INSTALLATION 5. On the Readme File Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. MB970 User’s Manual...
Driver, the Microsoft .NET Framework 3.5 SPI should be first installed. To install the VGA drivers, follow the steps below. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) Q7 Series Chipset Drivers. 2. Click Intel(R) Q77 Chipset Family Graphics Driver.
Page 55
DRIVERS INSTALLATION 3. When the Welcome screen appears, click Next to continue. 4. Click Yes to to agree with the license agreement and continue the installation. MB970 User’s Manual...
Page 56
DRIVER INSTALLATION 5. On the Readme File Information screen, click Next to continue the installation of the Intel® Graphics Media Accelerator Driver. 6. On Setup Progress screen, click Next to continue. 7. Setup complete. Click Finish to restart the computer and for changes to take effect.
Realtek HD Audio Driver Installation Follow the steps below to install the Realtek HD Audio Drivers. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) Q7 Series Chipset Drivers. 2. Click Realtek High Definition Audio Driver.
Page 58
DRIVER INSTALLATION 3. On the Welcome to the InstallShield Wizard screen, click Next to proceed with and complete the installation process. 4. The InstallShield Wizard Complete. Click Finish to restart the computer and for changes to take effect. MB970 User’s Manual...
DRIVERS INSTALLATION LAN Drivers Installation 1. Insert the CD that comes with the board. Click Intel and then Intel(R) Q7 Series Chipset Drivers. 2. Click Intel(R) PRO LAN Network Driver. MB970 User’s Manual...
Page 60
DRIVER INSTALLATION 3. Click Install Drivers and Software. 4. When the Welcome screen appears, click Next. MB970 User’s Manual...
Page 61
DRIVERS INSTALLATION 5. Click Next to to agree with the license agreement. 6. Click the checkbox for Drivers in the Setup Options screen to select it and click Next to continue. MB970 User’s Manual...
Page 62
DRIVER INSTALLATION 7. The wizard is ready to begin installation. Click Install to begin the installation. 8. When InstallShield Wizard is complete, click Finish. MB970 User’s Manual...
REMARKS: The Intel iAMT 8.0 Drivers can be installed on MB970VF, not MB970F. Follow the steps below to install the Intel Management Engine. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) AMT 8.0 Drivers. MB970 User’s Manual...
Page 64
DRIVER INSTALLATION 2. When the Welcome screen to the InstallShield Wizard for Intel® Management Engine Components, click the checkbox for Install Intel® Control Center & click Next. 3. Click Yes to to agree with the license agreement. MB970 User’s Manual...
Page 65
DRIVERS INSTALLATION 4. When the Setup Progress screen appears, click Next. Then, click Finish when the setup progress has been successfully installed. MB970 User’s Manual...
DRIVER INSTALLATION Intel® USB 3.0 Drivers 1. Insert the CD that comes with the board. Click Intel and then Intel(R) Q7 Series Chipset Drivers. 2. Click Intel(R) USB 3.0 Drivers. MB970 User’s Manual...
Page 67
DRIVERS INSTALLATION 3. When the Welcome screen to the InstallShield Wizard for Intel® USB 3.0 eXtensible Host Controller Driver, click Next. 4. Click Yes to to agree with the license agreement and continue the installation. MB970 User’s Manual...
Page 68
DRIVER INSTALLATION 5. On the Readme File Information screen, click Next to continue the installation of the Intel® USB 3.0 eXtensible Host Controller Driver. 6. Setup complete. Click Finish to restart the computer and for changes to take effect. MB970 User’s Manual...
Page 69
DRIVERS INSTALLATION This page is intentionally left blank. MB970 User’s Manual...
0F0h Clear Math Coprocessor Busy Signal 0F1h Reset Math Coprocessor 1F0h - 1F7h IDE Interface 2F8h - 2FFh Serial Port #2(COM2) 2B0h- 2DFh Graphics adapter Controller 360h - 36Fh Network Ports 3F8h - 3FFh Serial Port #1(COM1) MB970 User’s Manual...
The following table shows the IRQ used by the devices on board. Level Function IRQ0 System Timer Output IRQ1 Keyboard IRQ3 Serial Port #2 IRQ4 Serial Port #1 IRQ8 Real Time Clock IRQ14 Primary IDE IRQ15 Secondary IDE MB970 User’s Manual...