Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Drill Master 69079
Summary of Contents for Drill Master 69079
-
Page 2: Table Of Contents
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. Page 2 For technical questions, please call 1-800-444-3353. Item 69079... -
Page 3: Electrical Safety
A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Item 69079 For technical questions, please call 1-800-444-3353. Page 3... -
Page 4: Power Tool Use And Care
Service Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Page 4 For technical questions, please call 1-800-444-3353. Item 69079... -
Page 5: Circular Saw Safety Warnings
• Kickback is the result of saw misuse and/ or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below: Item 69079 For technical questions, please call 1-800-444-3353. Page 5... - Page 6 If unreadable or missing, contact equipment, such as those dust masks that are Harbor Freight Tools for a replacement. specially designed to filter out microscopic particles. 21. Avoid unintentional starting. (California Health & Safety Code § 25249.5, et seq.) Prepare to begin work before turning on the tool.
-
Page 7: Vibration Safety
If any abnormal seek medical advice as soon as possible. vibration occurs, stop use immediately. SAVE THESE INSTRUCTIONS. Item 69079 For technical questions, please call 1-800-444-3353. Page 7... - Page 8 Association, and the National Electrical Code. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Outlets for 2-Prong Plug Page 8 For technical questions, please call 1-800-444-3353. Item 69079...
-
Page 9: Extension Cords
Do not cover ventilation ducts. Keep flammable objects away. Amperes WARNING marking concerning Risk of Electric Shock. Properly connect power cord n 0 xxxx/min. No Load Revolutions per Minute (RPM) to appropriate outlet. Item 69079 For technical questions, please call 1-800-444-3353. Page 9... -
Page 10: Specifications
Guard Lever (38) Angle Gauge Angle Lock Knob (71) Saw Blade (Sold separately) Fence Lock Knob (69) Outer Flange (32) Base (64) Blade Bolt (31) Rip Fence (60) Figure 1 Page 10 For technical questions, please call 1-800-444-3353. Item 69079... -
Page 11: Operation
2. Adjust the Base to the desired angle between 0° Knob and 45°, using the Angle Gauge as a guide. Angle 3. Tighten in place with the Angle Lock Knob. Gauge Base Figure 4 Item 69079 For technical questions, please call 1-800-444-3353. Page 11... -
Page 12: Work Piece And Work Area Set Up
Trigger and wait until the Saw Blade stops spinning. feeding the Saw Blade into the workpiece. 11. To prevent accidents, unplug the Power Cord from its electrical outlet. Clean, then store the tool indoors out of children’s reach. Page 12 For technical questions, please call 1-800-444-3353. Item 69079... -
Page 13: Maintenance
See Extension Cords section on page 9. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Item 69079 For technical questions, please call 1-800-444-3353. Page 13... -
Page 14: Parts List And Diagram
Blade Bolt M6x16 Spring 6x40 Outer Flange Fence Lock Knob Inner Flange Angle Plate Cross Screw M4x12 Angle Lock Knob Lower Guard Plate Carriage Bolt M6x12 Pan Head Screw M4x12 Page 14 For technical questions, please call 1-800-444-3353. Item 69079... -
Page 15: Assembly Diagram
Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 69079 For technical questions, please call 1-800-444-3353. -
Page 16: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.