Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for CentralPneumatic 69927
Summary of Contents for CentralPneumatic 69927
-
Page 2: Table Of Contents
National pipe thread, straight NIOSH-approved dust mask/respirator. WARNING marking concerning WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved Risk of Explosion. safety goggles with side shields. Table A: Symbol Definitions Page 2 For technical questions, please call 1-800-444-3353. Item 69927 69928... -
Page 3: Work Area
A dust mask, non-skid safety shoes and finger on trigger, the tool is able to fire a fastener. a hard hat must be used for the applicable conditions. Wear heavy-duty work gloves during use. Item 69927 For technical questions, please call 1-800-444-3353. Page 3 69928... -
Page 4: Tool Use And Care
Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. SAVE THESE INSTRUCTIONS. Page 4 For technical questions, please call 1-800-444-3353. Item 69927 69928... - Page 5 17. Keep clear of the workpiece near the area being fastened. Fasteners may bend sideways during firing, causing them to exit the workpiece at an unexpected point, causing personal injury. Item 69927 For technical questions, please call 1-800-444-3353. Page 5 69928...
- Page 6 7. To reduce vibration, maintain tool as explained as tingling, numbness, and white or blue fingers), in this manual. If abnormal vibration occurs, seek medical advice as soon as possible. stop immediately. SAVE THESE INSTRUCTIONS. Page 6 For technical questions, please call 1-800-444-3353. Item 69927 69928...
-
Page 7: Specifications
Depth Adjustment Safety Screw Nosepiece Safety Nosepiece - Also called the workpiece contact, the Safety Nosepiece helps prevent the tool from firing unless it is pressed against an object. Item 69927 For technical questions, please call 1-800-444-3353. Page 7 69928... -
Page 8: Setup
3. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. Page 8 For technical questions, please call 1-800-444-3353. Item 69927 69928... - Page 9 Item 69927 For technical questions, please call 1-800-444-3353. Page 9 69928...
- Page 10 Page 10 For technical questions, please call 1-800-444-3353. Item 69927 69928...
-
Page 11: Operation
The tool must not cycle (fire). If it fails to act in the manner explained in bold, have it repaired by a qualified service technician. Item 69927 For technical questions, please call 1-800-444-3353. Page 11 69928... - Page 12 Only a skilled operator who is aware of the hazards and uses proper, safe work practices should use contact trip / bump fire operation. Single Sequential Contact Trip Position Position Figure C: Trigger Mode Switch Positions Page 12 For technical questions, please call 1-800-444-3353. Item 69927 69928...
-
Page 13: Loading The Tool
Release the trigger again. f. Clean external surfaces with clean, dry cloth. g. Store indoors out of children’s reach. Item 69927 For technical questions, please call 1-800-444-3353. Page 13 69928... -
Page 14: Maintenance
• misalignment or binding of moving parts, and will also reduce wear on the tool. • cracked or broken parts, and • any other condition that may affect its safe operation. Page 14 For technical questions, please call 1-800-444-3353. Item 69927 69928... -
Page 15: Clearing Jams
Use a screwdriver to release the jammed fastener by probing the openings in the magazine. 4. If the jam cannot be cleared using the method above, have the tool serviced by a qualified technician. Item 69927 For technical questions, please call 1-800-444-3353. Page 15 69928... -
Page 16: Troubleshooting
3. Replace damaged components. 4. Dirty, worn or damaged valve. 4. Clean or replace valve assembly. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. Page 16 For technical questions, please call 1-800-444-3353. Item 69927 69928... - Page 17 Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 69927 For technical questions, please call 1-800-444-3353. Page 17...
-
Page 18: Parts List And Diagram
Parts List and Diagram 69927 Parts List and Diagram Part Description Part Description Part Description Screw Spring Washer Spring Spring Washer Screw Mode Switch Bushing Spring Rail Exhaust Cover Safety Bracket A Washer Seal Screw Screw Bushing Washer Spring Washer... - Page 19 Trigger Valve Guide End Cap Bumper A Spring Screw M5×20 Bumper B Locking Washer Ø3 Air Plug Body Trigger O-ring 62.3×1.8 Rotating Shaft Bushing Nose Steel Ball REV 12e Item 69927 For technical questions, please call 1-800-444-3353. Page 19 69928...
-
Page 20: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.