AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Index INTRODUCTION ........................... 5 FUNCTION AND FEATURES ..................... 6 APPEARANCE AND INTERFACE ..................... 7 ..........................7 PPEARANCE ....................... 8 NTERFACE OF QUIPMENT NETWORK CONNECTION ......................9 ...................... 9 ONNECTION NSTRUCTION ........................ 10 ISIT NSTRUCTION VISIT IP CAMERA FROM LAN ....................
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 1 Introduction The IP Camera combines a high quality digital video camera with network connectivity and a powerful web server to bring clear video to your mobile phone/desktop from anywhere on your local network or over the Internet.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 2 Function and Features 32-bits RISC processor and special video encoder which can be up to 3M pixels encoding performance Support H.264 Main Profile@Level3.0 compression format, bit rate is smaller, and the image is more clear. It is more convenient for transferring through Internet and save more storage space.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 3.2 Interface of Equipment Figure 2 1) Power Input Socket: Connect DC adaptor, its output should be 5V power specification. 2) WIFI Antenna Hole: Install the WIFI antenna. 3) RESET Button: Press the RESET button and hold on more than 10 seconds, the equipment will restart and recover to the factory default settings.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Input pins Switch PIR Power Figure 4 The detector should be switched type (always on or always off). If the detector has detected the smoke or people or animal to enter the area, the detector will switch on or switch off. And it will send the external alarm signal into the IP camera.
The IP addresses of IP Camera and PC should be at the same segment, in Figure 5, the IP Camera-1 can’t be visited. Run the WIPC408HD Utility in the CD, click Search button, and then select the IP Camera to reset the IP Camera’s IP address, as the Figure 6.
Page 11
WIPC408HD IP CAMERA USER MANUAL v2.0 Figure 6 If you have the firewall software in your PC, when you run the WIPC408HD Utility, it may pop up a window to say if you want to block this program or not, then you should choose not to block.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 is: admin, password is: admin). Click “Update”. The setting will take effect now. Select the device in list box, click “Browse” button, it will open the Browser automatically and pop up a window at the same time which requires to inputting the user name and password.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Figure 9 5.2.1 Menu Column There are 2 kinds of menu, one is Main Menu, the other is Sub Menu. The Main Menu lies at the top of the interface, including View, Media, Network, Alarm, Advanced and System;...
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Camera will play the achieved audio. Click it again, the speaker will stop playing. 7) Audio Play Button: Click it to play the audio getting from IP Camera, click it again, it will disable this function.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Figure 12 , these buttons are for play, stop, the previous recorder, the next recorder, open the recorder file. Please click the button of “open the recorder file” first, and select the file you want to play, you can playback the recorder.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Open the Router Setting interface on PC-1. The interfaces for different routers are different, and the Port Forwarding settings are different, please refer to the Router’s Manual on how to set. For most routers, “Port Forwarding” option can be found in the Setting / Firewall Interface.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Camera-1. The WAN IP address can be searched on DDNS by domain name. Herein, domain name substitute the dynamic IP address. If the device can’t be visited by IP address, this domain name is also unavailable.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 7 Other Settings 7.1 Video Setting Page 7.1.1 Video Setting Figure 16 Resolution Use 1280 X 720 Resolution, Bit Rate is 2048 kbps and Frame Rate is up to 30 fps. The higher the resolutior or quality of the picture, then the bit rate will also be higher and will take more bandwidth.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 7.1.2 Audio Setting Figure 17 Audio Options User can define value for input and output volume.(100 being the highest value). First Stream Audio capture function can be open or close and audio type can be G.711 or G.726. G.711 bit rate is higher, but more clearly, G.726 compression rate is also high.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 will be disabld. 7.2 Network Setting Page 7.2.1 Basic Network Setting Figure 19 1) LAN Setting: The default setting of this equipment is showed as above Figure 19, user can change it according to your network environment.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Figure 20 The wireless setting page is showed as below Figure 20, user can click the “Search” button, and it will show you the WIFI network it has detected. Please select one, and the network data will fill in the blanks automatically.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 7.3.2 Motion Detection Setting Figure 22 If user wants to monitor a certain area’s movement, please select the motion detection to trigger alarm. The motion detection setting page is showed in Figure 22. This equipment supports location in four areas.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Figure 23 7.3.4 Alarm Time Setting / Schedule Example below: Alarm set is Monday, Wednesday, Friday at 3PM to 6:00PM 0 - 23 denotes standard format of time (24 hour clock) Left box indicates first 30 minutes / half hour ( 00:01 – 00:30)
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Figure 24 IP Camera will trigger alarm only on the time set by Figure 24. Please adjust the system time first. Refer to Part 7.5.2 7.4 Advance Setting 7.4.1 User Management There are three levels of authorization; namely Admin/User/Guest. Admin has the highest authority, it can do any change to the settings.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Figure 26 Figure 27 7.4.2 Auto Capture Setting Figure 28 Please tick “save picture on the SD card”, the equipment will snapshot every short time (for example, showed as Figure 28, every 60 seconds)
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 7.4.3 E-mail Setting Figure 29 In Figure 29, the blanks which have been filled with info should be correct. If any info is not filled right, the setting will fail. Before setting these parameters, please refer the settings of Outlook Express.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Figure 30 In order to use FTP function, user should apply username and password on the FTP server first. And please apply some storage, and the authority to write and create sub-category into it.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 7.5.2 Date and Time Setting Figure 33 Please refer to above Figure 33. Select the time zone first. There are three options to set the time and date. One is manually, another is keeping the same as the time and date of the computer, and the third one is getting it from the NTP server.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 7.5.4 System Log Checking Figure 35 8 Advanced Application 8.1 Android and iPhone Mobile Application Set Up The following are Step–by– Step Procedure for Android / iPhone App Set Up: 1) Download and Install ‘Aztech IP Cam’...
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 8.2 Mobile Phone Browsing After connecting to the network, you can view by using your mobile phone. Device will send MJEPG picture to mobile phone, you can set the image resolution, which is mentioned on Chapter 7.1.1.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Figure 38 2) The Settings to Use Safari in MAC OS When using MAC OS, because QuickTime is the default software, user only need go to Utilities folder under the Applications folder, and start command line program (Terminal...
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Figure 39 For more information, pls. refer the <<Multi Device Monitor System >> in CD. 9 Technical Parameters Item Sub item Description Sensor 1/4" CMOS sensor Total of pixel 720P (1280 X 720)
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 TCP/IP、 HTTP、 SMTP、 FTP、 DHCP、 DDNS、 Basic Protocol Network UPNP、NTP Other Protocol 802.11b/g/n Mobile Phone View support Video control support Dual way audio support Memory Snap or video into SD card Browser SD card...
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 able to access the IP Camera remotely using another computer. 10.1.1 Aztech DSL1015EW(S) / DSL1016EN(S2) Open your browser. Type-in 192.168.1.254 on the address bar and then press Enter. Go to Firewall Configuration, click Port Forwarding...
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Select the Server Name by clicking on Remove check box Click Remove button 10.1.2 Aztech DSL7000GRV(S) 1. Open your browser. 2. Type-in 192.168.1.254 on the address bar and then press Enter. 3. Go to Firewall Configuration, click Port Forwarding 4.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 To Remove: Select the Server Name by clicking on Remove check box Click Remove button 10.1.3 Aztech DSL7000GR(SME) 1. Open your browser. 2. Type-in 192.168.1.254 on the address bar and then press Enter.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 Select the Server Name by clicking on Remove check box Click Remove button 10.1.4 Linksys E1500 Router 1. Open your browser. 2. Type-in 192.168.1.1 on the address bar and then press Enter. 3. Type correct Username and Password if required.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 10.1.5 DLink DVG-N5402SP 1. Open your browser. 2. Type-in 192.168.0.1 on the address bar and then press Enter. 3. Type correct Username and Password if required. 4. Go to Advanced Tab, click Firewall and DMZ at the left column.
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 10.1.6 2wire 2700 HGV-2 1. Open your browser. 2. Type-in 192.168.1.254 on the address bar and then press Enter to enter the Web User Interface Page of your router. 3. Click Connection Status, this will launch the configuration page.
Page 40
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 5. Click Allow Individual Application (s) and select User-Defined from the drop down box then click Add a new user-defined application. 6. On the Application Name box input the IP Camera’s Name, select TCP on the Protocol option.
Page 41
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 7. WIPC408HD IP Camera Configuration will be added on the Definition List Table. Click Back to return to the Firewall Settings.
Page 42
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 8. Click Home Network again then click Edit Firewall Settings on the WIPC408HD Wired Connection.
Page 43
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0 9. Under the All Application box select WIPC408HD then click ADD for the application to be added on the Hosted Application list. Click DONE for the settings to take effect.
Page 44
AZTECH WIPC408HD IP CAMERA USER MANUAL v2.0...