Central Pneumatic 69575 Owner's Manual & Safety Instructions

Central Pneumatic 69575 Owner's Manual & Safety Instructions

16 gauge finish nailer

Advertisement

Advertisement

Table of Contents
loading

Summary of Contents for Central Pneumatic 69575

  • Page 2: Table Of Contents

    National pipe thread, straight NIOSH-approved dust mask/respirator. WARNING marking concerning WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved Risk of Explosion. safety goggles with side shields. Table A: Symbol Definitions Page 2 For technical questions, please call 1-800-444-3353. Item 69575...
  • Page 3: Work Area

    A dust mask, non-skid safety shoes and finger on trigger, the tool is able to fire a fastener. a hard hat must be used for the applicable conditions. Wear heavy-duty work gloves during use. Item 69575 For technical questions, please call 1-800-444-3353. Page 3...
  • Page 4: Tool Use And Care

    Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. SAVE THESE INSTRUCTIONS. Page 4 For technical questions, please call 1-800-444-3353. Item 69575...
  • Page 5 17. Keep clear of the workpiece near the area being fastened. Fasteners may bend sideways during firing, causing them to exit the workpiece at an unexpected point, causing personal injury. Item 69575 For technical questions, please call 1-800-444-3353. Page 5...
  • Page 6 7. To reduce vibration, maintain tool as explained as tingling, numbness, and white or blue fingers), in this manual. If abnormal vibration occurs, seek medical advice as soon as possible. stop immediately. SAVE THESE INSTRUCTIONS. Page 6 For technical questions, please call 1-800-444-3353. Item 69575...
  • Page 7: Specifications

    Maximum Air Pressure 110 PSI Air Inlet 1/4"–18 NPT Air Consumption 1 CFM @ 90 PSI Safety Mechanism Type Full Sequential 16 Gauge Finish Nail, Nail Type 1" to 2-1/2" Magazine Capacity Item 69575 For technical questions, please call 1-800-444-3353. Page 7...
  • Page 8 Safety Nosepiece - Also called the workpiece contact, the Safety Nosepiece helps prevent the tool from firing unless it is pressed against an object. Air Deflector Air Inlet Plug Trigger Magazine Depth Adjustment Knob Pusher Safety Nosepiece Page 8 For technical questions, please call 1-800-444-3353. Item 69575...
  • Page 9: Setup

    3. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. Item 69575 For technical questions, please call 1-800-444-3353. Page 9...
  • Page 10 Page 10 For technical questions, please call 1-800-444-3353. Item 69575...
  • Page 11 Item 69575 For technical questions, please call 1-800-444-3353. Page 11...
  • Page 12: Operation

    The tool must not cycle (fire). repaired by a qualified service technician. If it fails to perform in the manner explained in bold, have it repaired by a qualified service technician. Page 12 For technical questions, please call 1-800-444-3353. Item 69575...
  • Page 13: Loading The Tool

    Release the trigger again. 4. Adjust the Depth Adjustment Knob e. Clean external surfaces with clean, dry cloth. to control the firing depth. f. Store indoors out of children’s reach. Item 69575 For technical questions, please call 1-800-444-3353. Page 13...
  • Page 14: Maintenance

    • misalignment or binding of moving parts, and will also reduce wear on the tool. • cracked or broken parts, and • any other condition that may affect its safe operation. Page 14 For technical questions, please call 1-800-444-3353. Item 69575...
  • Page 15: Clearing Jams

    Pusher all the way back to the engaged position. Use a screwdriver to release the jammed fastener Driver Guide by probing the openings in the magazine. Cover Plate Figure D: Driver Guide and Cover Plate Detail Item 69575 For technical questions, please call 1-800-444-3353. Page 15...
  • Page 16: Troubleshooting

    3. Replace damaged components. 4. Dirty, worn or damaged valve. 4. Clean or replace valve assembly. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. Page 16 For technical questions, please call 1-800-444-3353. Item 69575...
  • Page 17 LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Item 69575 For technical questions, please call 1-800-444-3353. Page 17...
  • Page 18: Parts List And Diagram

    Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 18 For technical questions, please call 1-800-444-3353. Item 69575...
  • Page 19 Assembly Diagram Item 69575 For technical questions, please call 1-800-444-3353. Page 19...
  • Page 20: Warranty

    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

Table of Contents