Central Pneumatic 69704 Owner's Manual & Safety Instructions

Central Pneumatic 69704 Owner's Manual & Safety Instructions

Heavy duty air paint spray gun

Advertisement

Advertisement

Table of Contents
loading

Summary of Contents for Central Pneumatic 69704

  • Page 2: Table Of Contents

    Distractions are able to result in fire, and injury to persons. the loss of control of the tool. Page 2 For technical questions, please call 1-800-444-3353. Item 69704...
  • Page 3: Personal Safety

    Use only lubricants supplied with the by qualified repair personnel. tool or specified by the manufacturer. b. When servicing a tool, use only identical replacement parts. Use only authorized parts. Item 69704 For technical questions, please call 1-800-444-3353. Page 3...
  • Page 4: Air Source

    Risk of Respiratory Injury. Wear NIOSH-approved respirator. Cubic Feet per Minute flow SCFM at standard conditions WARNING marking concerning Risk of Explosion. National pipe thread, tapered National pipe thread, straight Page 4 For technical questions, please call 1-800-444-3353. Item 69704...
  • Page 5: Specifications

    115 PSI Cup Capacity 1 quart Air Inlet 1/4 IN. –  1 8 NPS Air Consumption 10 CFM @ 60 PSI Nozzle Size 1.8 mm Recommended Hose Size 3/8 IN. ID Item 69704 For technical questions, please call 1-800-444-3353. Page 5...
  • Page 6: Setup

    5. Turn on the air compressor according to more efficient, but are not required. the manufacturer’s directions and allow it to build up pressure until it cycles off. Page 6 For technical questions, please call 1-800-444-3353. Item 69704...
  • Page 7 7. Inspect the air connections for leaks. measure to attempt to discharge the tool in a Repair any leaks found. safe fashion after disconnecting to ensure that the tool is disconnected and unpowered. Item 69704 For technical questions, please call 1-800-444-3353. Page 7...
  • Page 8 NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Page 8 For technical questions, please call 1-800-444-3353. Item 69704...
  • Page 9 Cup Cover Yoke to allow free movement while working. 3. Before spraying, mask nearby Figure C: Components and Controls objects not being sprayed and lay cloths (not included) on the floors. Item 69704 For technical questions, please call 1-800-444-3353. Page 9...
  • Page 10 (not included) and mix thoroughly. Use the proper thinner for the type of paint. Thin CAUTIOUSLY. Proceed slowly, adding minimal amounts at a time. DO NOT exceed the manufacturer’s thinning recommendations. Page 10 For technical questions, please call 1-800-444-3353. Item 69704...
  • Page 11 12. After setting up a piece of scrap material, squeeze the Trigger in short bursts while turning the Fluid Knob counterclockwise to set the amount of fluid - see Figure F: Fluid Adjustment. Item 69704 For technical questions, please call 1-800-444-3353. Page 11...
  • Page 12: Spraying Technique

    3. Using two hands, one to steady the Cup 7. Clean Spray Gun thoroughly immediately and the other to operate the Spray Gun, after EVERY use, according to aim Nozzle at the workpiece. instructions on the following pages. Page 12 For technical questions, please call 1-800-444-3353. Item 69704...
  • Page 13: Maintenance

    • damaged air supply hose, • misalignment or binding of moving parts, • cracked or broken parts, and • clogged nozzle, • any other condition that may affect its safe operation. Item 69704 For technical questions, please call 1-800-444-3353. Page 13...
  • Page 14 Air Supply Maintenance Every day, perform maintenance on the air supply according to the component manufacturers’ instructions. Storage Store in a dry, secure area out of reach of children. Page 14 For technical questions, please call 1-800-444-3353. Item 69704...
  • Page 15 Nozzle are plugged. left only 3. Damaged Needle. 3. Have qualified technician replace Needle. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. Item 69704 For technical questions, please call 1-800-444-3353. Page 15...
  • Page 16 4. Worn/damaged air valve/seat. 4. Replace air valve. 5. Bent valve stem. 5. Replace valve stem. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. Page 16 For technical questions, please call 1-800-444-3353. Item 69704...
  • Page 17 AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Item 69704 For technical questions, please call 1-800-444-3353. Page 17...
  • Page 18: Parts List And Diagram

    Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 18 For technical questions, please call 1-800-444-3353. Item 69704...
  • Page 19: Assembly Diagram

    NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Assembly Diagram Item 69704 For technical questions, please call 1-800-444-3353. Page 19...
  • Page 20: Warranty

    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

Table of Contents