Husqvarna LGT24K54 Operator's Manual

Ride-on mowers
Hide thumbs Also See for LGT24K54:

Advertisement

Available languages

Available languages

Operator's Manual
Gasoline containing up to 10% ethanol (E10) is accept-
able for use in this machine. The use of any gasoline ex-
ceeding 10% ethanol (E10) will void the product warranty.
Manual de Operario
Esta máquina puede utilizar gasolina con un contenido
de hasta el 10% de etanol (E10). El uso de una gasolina
LGT24K54
que supere el 10% de etanol (E10) anulará la garantía
del producto. the product warranty.
Please read the operator's manual carefully and make sure
you understand the instructions before using the machine.
532 44 17-90 Rev 2
Por favor lea cuidadosamente y comprenda
English/Spanish
estas intrucciones antes de usar esta maquina.

Advertisement

Chapters

Table of Contents
loading

Summary of Contents for Husqvarna LGT24K54

  • Page 1 Manual de Operario Esta máquina puede utilizar gasolina con un contenido de hasta el 10% de etanol (E10). El uso de una gasolina LGT24K54 que supere el 10% de etanol (E10) anulará la garantía del producto. the product warranty. Please read the operator's manual carefully and make sure you understand the instructions before using the machine.
  • Page 2: Safety Rules

    SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • Never leave a running machine unattended. Always turn WARNING: In order to prevent ac ci den tal off blades, set parking brake, stop engine, and remove starting when setting up, trans port ing,...
  • Page 3 SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN • If fuel is spilled on clothing, change clothing immediately. • Never overfill fuel tank. Replace gas cap and tighten securely. WARNING. CHILDREN CAN BE INJURED BY THIS EQUIPMENT. The American Academy GENERAL SERVICE of Pediatrics recommends that children be a •...
  • Page 4: Table Of Contents

    PRODUCT SPECIFICATIONS CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manu fac tured to Gasoline Capacity 4 Gallons/15,14 L give you the best possible dependability and performance. and type: Unleaded Regular Should you experience any problem you cannot easily Oil Type (API: SG-SL): SAE 30 (above 32°F/0°C) remedy, please contact your nearest authorized service...
  • Page 5: Unassembled Parts

    UNASSEMBLED PARTS Mower Mower Front Wheel (2) Rear Lift Link (1) Shoulder Bolt Assemblies (1) 1-1/4 O.D. Washer (1) Small Retainer Springs (1) Front Lift Link (1) 3/8-16 Assembly (1) Wheel Locknut (5) Large Retainer Springs Slope Sheet (1) Oil Drain Tube If Equipped Keys (1) 3/4 O.D.
  • Page 6: Assembly

    ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.
  • Page 7 ASSEMBLY 4. SLIDE MOWER UNDER TRACTOR (See Fig. 7) • Bring belt forward and check belt for proper routing in LIFT all mower pulley grooves. LEVER NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor. •...
  • Page 8 ASSEMBLY 7. ATTACH REAR LIFT LINKS (C) (See Fig. 13) • Insert rod end of rear lift link (C) into hole (U) in tractor ANTI-SWAY BAR TRANSAXLE (S) LOCATION BRACKET (T) lift shaft suspension arm and pivot link down to mower. LOCATED •...
  • Page 9: Assembly

    ASSEMBLY ✓ 9 INSTALL BELT ON ENGINE CLUTCH PULLEY (M) CHECKLIST (See Fig. 6 & 15) • Disengage belt tension rod (K) from locking bracket (L). BEFORE YOU OPERATE YOUR NEW TRAC TOR, WE • Install belt onto engine clutch pulley (M). WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.
  • Page 10: Operation

    OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. FAST REVERSE HIGH SLOW NEUTRAL CHOKE IGNITION SWITCH ENGINE START ENGINE ON PARKING BRAKE MOWER HEIGHT MOWER LIFT ENGINE OFF REVERSE OPERATION SYSTEM (ROS)
  • Page 11: Operation

    OPERATION KNOW YOUR TRACTOR READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Fig.
  • Page 12 OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide vision safety mask worn over spectacles.
  • Page 13 OPERATION TO ADJUST GAUGE WHEELS (See Fig. 22) TO MOVE FORWARD AND BACKWARD (See Fig. 20) Gauge wheels are prop er ly ad just ed when they are slight ly off the ground when mower is at the desired cutting height The direction and speed of movement is controlled by the in operating position.
  • Page 14 OPERATION TO OPERATE ON HILLS TO STOP MOWER BLADES - Disengage at tach ment clutch con trol. CAUTION: Do not drive up or down hills with slopes greater than 15° and do not CAUTION: Do not operate the mower drive across any slope. without either the en tire grass catcher, on mowers so equipped, or the deflector shield •...
  • Page 15: Before Starting The Engine

    OPERATION SERVICE REMINDER/HOUR METER TO START ENGINE (See Fig. 16) When starting the engine for the first time or if the engine Service reminder shows the total number of hours the engine has run out of fuel, it will take extra cranking time to move has run and flashes to indicate that the engine or mower fuel from the tank to the engine.
  • Page 16 OPERATION PURGE TRANSMISSION MOWING TIPS • Tire chains cannot be used when the mower hous ing CAUTION: Never engage or disengage is attached to tractor. freewheel lever while the engine is run ning. • Mower should be properly leveled for best mowing performance.
  • Page 17: Maintenance Schedule

    MAINTENANCE BEFORE EVERY EVERY EVERY EVERY EVERY BEFORE MAINTENANCE EACH SEASON STORAGE SCHEDULE HOURS HOURS HOURS HOURS Check Brake Operation Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Clean Debris Off Steering Plate ck Transaxle Cooling...
  • Page 18: Maintenance

    MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Re place Always observe safety rules when per form ing any bent or damaged blades. main te nance. CAUTION: Use only a replacement blade ap- BRAKE OPERATION proved by the manufacturer of your tractor.
  • Page 19: V-Belts

    MAINTENANCE TO CHANGE ENGINE OIL (See Fig. 29 & 30) V-BELTS Determine temperature range expected before oil change. Check V-belts for deterioration and wear after 100 hours All oil must meet API service classification SG-SL. of operation and replace if necessary. The belts are not •...
  • Page 20: Clean Air Screen

    MAINTENANCE AIR FILTER CLEANING Your engine will not run properly using a dirty air filter. • Clean engine, battery, seat, finish, etc. of all foreign Service air cleaner more often under dusty conditions. matter. See engine manual. • Clean debris from steering plate. Debris can restrict clutch/brake pedal shaft movement, causing belt slip CLEAN AIR SCREEN and loss of drive.
  • Page 21: Deck Washout Port

    MAINTENANCE DECK WASHOUT PORT (See Fig. 33) Your tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach.
  • Page 22: Service And Adjustments

    SERVICE AND ADJUSTMENTS WARNING: TO AVOID SE RI OUS IN JU RY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place motion control lever in neutral position. • Place attachment clutch in “DISENGAGED” position. •...
  • Page 23 SERVICE AND ADJUSTMENTS TO LEVEL MOWER • If adjustment is necessary, see steps in Visual Adjust- ment instructions above. Make sure tires are properly inflated to the PSI shown on • Recheck measurements, adjust if necessary until both tires. If tires are over or under inflated, it may affect the sides are equal.
  • Page 24: Front Wheel Toe-In/Cam Ber

    SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT TO CHECK BRAKE (See Fig. 40) If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved Park the tractor on level surface. En gage parking brake. surface, then brake must be serviced.
  • Page 25 SERVICE AND ADJUSTMENTS TRANSAXLE MOTION CONTROL LEVER TO START ENGINE WITH A WEAK BATTERY NEUTRAL ADJUSTMENT (See Fig. 42) (See Fig. 43) The motion control lever has been pre set at the factory WARNING: Lead-acid batteries gen- and adjustment should not be necessary. er ate ex plo sive gases.
  • Page 26: Interlocks And Relays

    SERVICE AND ADJUSTMENTS TO REMOVE HOOD AND GRILL ASSEMBLY REPLACING BATTERY (See Fig. 44) (See Fig. 45) WARNING: Do not short battery ter mi- • Raise hood. nals by allowing a wrench or any other • Unsnap headlight wire connector. object to contact both terminals at the •...
  • Page 27: Storage

    SERVICE AND ADJUSTMENTS Immediately prepare your tractor for storage at the end ENGINE of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS WARNING: Never store the trac tor with FROM FORMING IN ES SEN TIAL FUEL SYSTEM PARTS SUCH gas o line in the tank inside a building AS CARBURETOR, FUEL FIL TER, FUEL HOSE, OR TANK...
  • Page 28: Troubleshooting

    TROUBLESHOOTING PROBLEM CAUSE CORRECTION 1. Out of fuel. 1. Fill fuel tank. Will not start 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4.
  • Page 29: Trou Ble Shoot Ing

    TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues 1. Faulty operator-safety presence control 1. Check wiring, switches and connections. If not system. corrected, contact an authorized service center/ to run when oper- department. ator leaves seat with attachment clutch engaged 1. Worn, bent or loose blade. 1.
  • Page 35: Español

    REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles PELIGRO: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. •...
  • Page 36 REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles III. NIÑOS • Si se vierte carburante sobre la ropa, cambiarse la ropa inmediatamente. • Nunca llenar el depósito más de lo debido. Volver a colocar ADVERTENCIA: LOS NIÑOS PUEDEN SUFRIR DA- el tapón del gas y cerrar de modo firme.
  • Page 37: Especificaciones Del Producto

    ESPECIFICACIONES DEL PRODUCTO FELICITACIONES por la compra de su tractor. Ha sido diseñado, planificado y fabricado para darle la mejor confiabilidad y el mejor Capacidad y Tipo 4 Galones/15.14 L rendimiento posible. de gasolina: Regular Sin Plomo En el caso de que se encuentre con cualquier problema que no Tipo de Aceite: SAE 30 (Sobre 32°F/0°C) pueda solucionar fácilmente, haga el favor de ponerse en con-...
  • Page 38 PIEZAS SIN MONTAR Segadora Rueda Delantera De La Segadora (2) Conjunto de eslabones (1) Perno de levantamiento (5) 1-3/16” (1) 1-1/4” traseros Arandela Arandela (1) Abrazadera pequeño de retención (1) 3/8-16” (1) Eslabones (1) Rueda de levantamiento Tuerca delanteros (5) Abrazadera grande de retención Hoja de pendiente (1) Tubo de desagüe...
  • Page 39: Montaje/Pre Operación

    MONTAJE Su tractor nuevo ha sido montado en la fábrica con la excepción de aquellas partes que no se han montado por razones de envío. Para asegurarse que su tractor funcione en forma adecuada y segura todas las partes y los artículos de ferretería que se monten tienen que ser apretados en forma segura.
  • Page 40 MONTAJE 4. DESLICE LA CORTADORA DE CÉSPED DEBAJO DEL TRACTOR (Vea Fig. 7) PALANCA DE • Lleve la correa hacia adelante y verifique que su trayectoria LEVANTAMIENTO sea correcta en todos los surcos de la polea de la cortadora de césped. NOTA: asegúrese de que los brazos de suspensión lateral de la cortadora de césped (A) estén orientados hacia adelante antes de deslizar la cortadora de césped debajo del tractor.
  • Page 41 MONTAJE 7. INSTALE LOS ESLABONES DE LEVANTAMIENTO TRA- UBICACIÓN ESCUADRA DE SEROS (C) (Vea Fig. 13) DE LA BARRA TRANSEJE (T) ANTIBALANCEO (S) • Inserte el extremo de varilla del eslabón de levantamiento UBICADA ENTRE trasero (C) dentro del agujero (U) en el brazo de suspensión LAS RUEDAS del eje de levantamiento del tractor y haga oscilar el eslabón hacia abajo hacia la cortadora de césped.
  • Page 42 MONTAJE 9. INSTALE LA CORREA EN LA POLEA DEL EMBRAGUE ✓ DEL MOTOR (M) (Vea Fig. 6 & 15) LISTA DE REVISIÓN • Desenganche la varilla tensora de la correa (K) de la escuadra ANTES DE OPERAR Y DE DISFRUTAR DE SU TRACTOR de bloqueo (L).
  • Page 43: Operación

    OPERACIÓN Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados. RÁPIDO MARCHA ATRÁS ALTO BAJO LENTO NEUTRO ESTRANGU- IGNICIÓN LACIÓN FRENO DE MOTOR MOTOR FRENO DE ABIERTA MOTOR ESTACIONAMIENTO ENCENDIDO ESTACIONAMIENTO SISTEMA...
  • Page 44 OPERACIÓN FAMILIARICESE CON SU TRACTOR LEA ESTE MANUAL DEL OPERARIO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU TRACTOR Compare las ilustraciones con su tractor para familiarizarse con las ubicaciones de los diversos controles y ajustes. Guarde este manual para referencia en el futuro. Fig.
  • Page 45 OPERACIÓN La operación de cualquier tractor puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o pro tec cio nes para los ojos mientras opere su tractor o cuando haga ajustes o reparaciones. Recomendamos gafas de seguridad o una máscara de visión amplia de seguridad usada sobre las gafas.
  • Page 46 OPERACIÓN PARA MOVERSE HACIA ADELANTE Y HACIA PARA AJUSTAR LAS RUEDAS CALIBRADORAS ATRÁS (Vea Fig. 20) (Vea Fig. 22) La dirección y la velocidad del movimiento son controladas por Las ruedas calibradoras están bien ajustadas cuando se en- medio de la palanca de control de movimiento (J). cuentran un poco a distancia del terreno al mismo tiempo que la segadora esté...
  • Page 47 OPERACIÓN FUNCIONAMIENTO ATRÁS (Vea Fig. 24) • Para volver a empezar con el movimiento, suelte len ta men te, Tu tractor está equipado con el Sistema de Funcionamiento Atrás el freno de estacionamiento y el pedal del embrague/freno. (ROS). Cualquier tentativa del operador de viajar marcha atrás •...
  • Page 48 OPERACIÓN ANTES DE HACER ARRANCAR EL MOTOR PARA HACER ARRANCAR EL MOTOR (Vea Fig. 16) Al hacer arrancar el mo tor por la primera vez o si se ha acabado REVISE EL NIVEL DE ACEITE DEL MOTOR el com bus ti ble del mo tor, se necesitará tiempo para el arranque ex tra para mov er el com bus ti ble desde el estanque hasta el mo tor.
  • Page 49 OPERACIÓN PURGAR LA TRANSMISIÓN CONSEJOS PARA SEGAR • No se pueden usar las cadenas para las llantas cuando la PRECAUCIÓN: Nunca enganche o desen- caja de la segadora está adjunta al tractor. ganche la palanca del control de rue da libre •...
  • Page 50: Tabla Del Mantenimiento

    MANTENIMENTO Revisar la operación del freno Revisar la presión de las llantas Vérifiéz la commande de présence d'opérateur et le sistema d ROS Revisar si hay sujetadores sueltos Afilar/cambiar las cuchillas de la segadora Tabla de lubricación Revisar el nivel Limpiar la batería y los terminales Revisar el enfriamiento del transeje Limpie los residuos de la placa de dirección.
  • Page 51 MANTENIMENTO TRACTOR CUIDADO DE LA CUCHILLA Para obtener resultados óptimos, las cuchillas de la cortadora Siempre observe las reglas de seguridad cuando dé mante ni- deben estar afiladas. Reemplace las cuchillas que estén gastadas, mien to. dobladas o dañadas. OPERACIÓN DEL FRENO PRECAUCIÓN: Usar solamente la hojas de Si el tractor necesita más de cinco (5) pies para detenerse repuesto aprobada por el fabricante de su cor-...
  • Page 52 MANTENIMENTO ENFRIAMIENTO DEL TRANSEJE PARA CAMBIAR EL ACEITE DEL MOTOR Las aletas de enfriamiento y el ventilador de la transmisión tienen (Vea Fig. 29 y 30) que mantenerse limpios para asegurar el enfriamiento adecuado. Determine la gama de la temperatura esperada antes de cam- No trate de limpiar el ventilador o la transmisión cuando el motor biar el aceite.
  • Page 53: Filtro Del Aire

    MANTENIMENTO LIMPIEZA FILTRO DEL AIRE • Limpie todo material extraño del motor, la batería, el asiento, Su motor puede sufrir averías y funcionar de manera incorrecta con el pulido, etc. un filtro del aire sucio. Déle servicio al filtro de aire más a menudo •...
  • Page 54 MANTENIMENTO PUERTO DE LAVADO DE LA CUBIERTA (Vea Fig. 33) La cubierta de su tractor está equipada con un puerto de lavado sobre la superficie que forma parte del sistema de lavado de la cubierta. Se debería utilizar cada vez que se haya usado el tractor. Lleve el tractor a un lugar horizontal y despejado de su césped, lo bastante cerca de una boca de riego como para que llegue la manguera del jardín.
  • Page 55: Servicio Y Ajustes

    SERVICIO Y AJUSTES ADVERTENCIA: PARA EVITAR LESIÓNES SERIAS, ANTES DE DAR CUALQUIER SERVICIO O DE HACER AJUSTES: • Presione el pedal de freno completamente y aplique el freno de estacionamiento. • Ponga el embrague del accesorio en la posición desenganchado (DISENGAGED). •...
  • Page 56 SERVICIO Y AJUSTES PARA NIVELAR LA SEGADORA • Vuelva a verificar las medidas y ajuste nuevamente, en caso necesario, hasta que ambos lados queden iguales. Asegúrese de que los neumáticos estén inflados a la PSI que se indica en estos. Si están demasiado inflados o poco AJUSTE DE DELANTE A ATRÁS (Vea Fig.
  • Page 57 SERVICIO Y AJUSTES CONTROLAR Y AJUSTAR EL FRENO PARA CAMBIAR LA CORREA DE IMPULSIÓN DE MOVIMIENTO (Vea Fig. 40) Si el tractor exige más de cinco (5) pies para pararse a una velo- cidad más alta en el cambio más alto en una superficie nivelada Estacione el tractor en una superficie nivelada.
  • Page 58 SERVICIO Y AJUSTES PARA HACER ARRANCAR EL MOTOR CON UNA REGULACIÓN DE LA PALANCA DE CONTROL DEL BATERÍA BAJA (Vea Fig. 43) MOVIMIENTO Neutro DEL CAMBIO MECÁNICO (Vea Fig. 42) ADVERTENCIA: Las baterías de ácido-plo- La palanca de control del movimiento del cambio mecánico ya mo generan gases explosivos.
  • Page 59 SERVICIO Y AJUSTES PARA REMOVER EL CONJUNTO DEL CAPÓ Y REEMPLAZAR LA BATERIA (Vea Fig. 44) DEL ENREJADO (Vea Fig. 45) ADVERTENCIA: No haga cortocircuito con los 1. Levante el capó. terminales de la batería al permitir que una 2. Desabroche el conector del alambre de las luces delanteras. llave de tuerca o cualquier otro objeto entre 3.
  • Page 60: Almacenamiento

    ALMACENAMIENTO MOTOR Inmediatamente prepare su tractor para el almacenamiento al final de la temporada o si el tractor no se va a usar por 30 días o más. SISTEMA DE COMBUSTIBLE Advertencia: Nunca almacene el tractor con IMPORTANTE: Es important evitar que se forman depositos gasolina en el estanque dentro de un edificio de goma en partes fundamentales del sistema de combus-tible en donde los gases pueden al can zar una...
  • Page 61: Identificación De Problemas

    IDENTIFICACIÓN DE PROBLEMAS PROBLEMA CAUSA CORRECCIÓN No arranca Sin combustible. Llene el estanque de combustible. Motor sin la “ESTRANGULACIÓN” (CHOKE) Vea “PARA HACER ARRANCAR EL MOTOR” en la sec- adecuada. ción de operación. Motor ahogado. Espere varios minutos antes detratar de arrancar. Bujía mala.
  • Page 62 IDENTIFICACIÓN DE PROBLEMAS PROBLEMA CAUSA CORRECCIÓN Vibración Cuchilla desgastada, doblada o suelta. Cambie la cuchilla. Apriete el perno de la cuchilla. excesiva Mandril de la cuchilla doblado. Cambie la mandril de la cuchilla. Parte(s) suelta(s)/dañada(s). Apriete la(s) parte(s). Cambie las partes dañadas. El motor continúa Sistema de control que exige la presencia del Revise el alambrado, los interruptores y la conexiones.Si...
  • Page 68 08/23/2011 TH...

Table of Contents