Table of Contents
Advertisement
Available languages
Available languages
Quick Links
Professional Motion
Sensor Quartz Security
Light for Canadian Tire
Model SL-5310
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
This package includes:
Cover
Plate
Sensor
Light Control
Requirements
• The light control requires 120-volts AC.
• This fixture is designed for wall mounting only.
• If you want to use Manual Override, the control must
be wired through a switch.
• Some codes require installation by a qualified
electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
• The backplate has knockouts so the sensor can be
mounted on most junction boxes.
• In some applications a universal adaptor plate may
be needed. Adaptors are available at Home Centers
and Electrical Supply Stores.
© 2007 HeathCo LLC
Cover Plate
Gasket
6 Screws
Halogen
(3 sizes)
Bulb
3 Wire Nuts
S-hook
OPERATION
Mode:
On-Time:
Test
5 Sec
Normal
1, 5, 10 min.
Manual
Until Dawn*
* resets to Auto Mode at dawn.
Note: When first turned on wait about 1
the circuitry to calibrate.
Put the ON-TIME switch on the
bottom of the sensor in the TEST
position.
Put the ON-TIME switch in the 1, 5 or
10 minute position.
MANUAL MODE
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5 or 10
position.
Mode Switching Summary
TEST
AUTO
MANUAL MODE
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.
Works:
Day
Night
x
/
minutes for
1
2
TEST
ON-TIME
TEST 1 5 10
AUTO
ON-TIME
TEST 1 5 10
1 Second OFF
then...
... back on.
Move ON-TIME Switch
to 1, 5, or 10 minutes
Flip light switch
off for one second
then back on*
598-1327-01
x
x
x
Advertisement
Table of Contents
Related Manuals for Heath Zenith SL-5310
Summary of Contents for Heath Zenith SL-5310
- Page 1 Professional Motion Sensor Quartz Security Light for Canadian Tire Model SL-5310 Features • Turns on lighting when motion is detected. • Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night).
-
Page 2: Installation
INSTALLATION CAUTION: Risk of fire. This fixture is designed for wall mounting only. DO NOT install on a ceiling or soffit. For easy installation, select an existing light with a wall switch for replacement. ❒ Attach the lamp arm to the backplate arm and secure with the long bolt. -
Page 3: Specifications
TEST AND ADJUSTMENT ❒ Turn on the circuit breaker and light switch. NOTE: Sensor has a 1 minute warm up period be- fore it will detect motion. When first turned on or when switching modes wait 1 ❒ Turn the RANGE control to the mid position and the ON-TIME control to the TEST position. -
Page 4: Troubleshooting Guide
TROUBLESHOOTING GUIDE SYMPTOM POSSIBLE CAUSE Light will not 1. Light switch is turned off. come on. 2. Light is loose or burned out. 3. Fuse is blown or circuit breaker is turned off. 4. Daylight turn-off is in effect (recheck after dark). - Page 5 Detector de Movimiento y Control de Faro Halógeno de Cuarzo para Canadian Tire Modelo SL-5310 Características • Prende la luz cuando detecta movimiento. • Apaga la luz automáticamente. • La fotocélula mantiene la luz apagada durante el día. • LED indica que se ha detectado movimiento (durante el día o la noche).
- Page 6 INSTALACION PRECAUCIóN: Riesgo de incendio. Esta aparato está diseñado solamente para montaje en pared. NO lo instale sobre el cielo raso o sofito. Para una fácil instalación escoja una luz con un interruptor de pared. ❒ Una el brazo de la lám- para de la placa posterior y asegúrela con el perno largo.
-
Page 7: Prueba Y Ajuste
PRUEBA Y AJUSTE ❒ Prenda el cortacircuitos y el interruptor de luz. NOTA: El detector tiene un período de cerca de 1 minutos de calentamiento antes de detectar movimiento. Cuando lo prenda por primera vez, espere 1 minutos. ❒ Gire el control RANGE a la posición media y el control ON-TIME a la posición TEST. -
Page 8: Guia De Investigacion De Averias
GUIA DE INVESTIGACION DE AVERIAS POSIBLE CAUSA SINTOMA La luz no se en- 1. El interruptor de luz está apagado. 2. El faro está flojo o fundido. ciende. 3. El fusible está quemado o el cortacir- cuitos está apagado. 4. La desconexión de luz del día está en efecto. - Page 9 Lampe á détecteur de mouvement professionnelle pour Canadian Tire Modèle SL-5310 Caractéristiques • Allume l’éclairage lorsqu’un mouvement est détecté. • Éteint automatiquement l’éclairage. • Photocellule qui maintient l’éclairage éteint pendant la période de lumière du jour. • La DEL indique qu’un mouvement a été détecté (jour ou nuit).
- Page 10 INSTALLATION Attention, risque d’incendie - Cet appareil est conçu pour montage mural seulement. NE PAS l’installer sur un plafond ou un soffite. Pour faciliter l’installation, choisir un appareil d’éclairage devant être remplacé et qui est déjà commandé par un interrupteur. ❒...
-
Page 11: Essais Et Réglages
ESSAIS ET RÉGLAGES ❒ Mettre en circuit le disjoncteur et l’interrupteur d’éclairage. NOTE: Le capteur doit se réchauffer de pouvoir détecter le mouvement. Lorsque l’appareil est mis en circuit ou changé de mode, attendre minute. ❒ Placez la commande RANGE à sa position intermédiaire et la commande ON-TIME à... -
Page 12: Guide De Dépannage
GUIDE DE DÉPANNAGE SYMPTÔME CAUSE POSSIBLE Les lampes 1. L’interrupteur d’éclairage est en position hors ne s’allument circuit. pas. 2. Les projecteurs sont brûles ou desserrés. 3. Le fusible du circuit a sauté ou le disjoncteur est en position hors circuit. 4.