Page 1
INSTALLATION INSTRUCTIONS FOR PART 95-3304 Buick/Chevy/Hummer/Pontiac/Saturn multi-kit 2005-2009 KIT FEATURES • Double DIN radio unit provision • Stacked ISO DIN head unit provision KIT COMPONENTS • A) Trim plate • B) Brackets WIRING & ANTENNA CONNECTIONS (Sold Separately) Wiring Harness: •...
Page 2
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. 95-3304 Applications Hummer H3 2006-2009 Pontiac Montana (SV6 only) 2005-2007...
Dash Disassembly 95-3304 Buick Terraza/Chevy Uplander Pontiac Montana SV6/Saturn Relay 1. Unclip and remove trim panel around radio and A/C control. (Figure A) 2. Remove (8) 9/32” screws to extract radio and A/C control from sub dash. Continue on next page...
Dash Disassembly 95-3304 Chevrolet Corvette 1. Unclip and remove ride control switch/blank plate at front edge of center console lid, Step 2. 2. Remove (2) 9/32” screws from under the removed blank plate, Step 3. 3. Unclip and remove entire panel surrounding radio and including A/C controls, Step 4.
Dash Disassembly 95-3304 Hummer H3 2006-2009 1. Unclip and remove trim panel around radio and A/C controls. (Figure A) 2. Remove (4) 9/32” screws securing radio. (Figure B) 3. Unplug and remove radio. Continue to kit assembly (Figure A) (Figure B)
Kit Assembly 95-3304 Double DIN head unit provision 1. Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A) 2 Slide the DDIN radio unit into the trim...
Kit Assembly 95-3304 Stacked ISO DIN head unit provision 1. Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A) 2 Slide the stacked ISO DIN units into the...
Page 11
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 95-3304 Buick/Chevy/Hummer/Pontiac/Saturn multi-kit 2005-2009 CARACTERÍSTICAS DEL KIT • Provisión de unidad central doble DIN • Provisión de unidad central ISO DIN vertical COMPONENTES DEL KIT • A) Placa de moldura • B) Soportes CABLEADO Y CONEXIONES DE ANTENA (se venden por separado) Arnés de cableado:...
Page 12
Regístrese en www.installerinstitute. 800-354-6782 for more information and take steps com o llame al 800-354-6782 para obtener más toward a better tomorrow. información y avance hacia un futuro mejor. 95-3304 APLICACIONES Hummer H3 2006-2009 Pontiac Montana (SV6 sólo) 2005-2007...
Page 13
95-3304 Indice Desmontaje del tablero - Buick Terraza 2005-2008 ... 4 - Chevrolet Corvette 2005-2009 ... 5 - Chevrolet Uplander 2005-2008 ... 4 - Hummer H3 2006-2009 ... 6 - Pontiac Montana (SV6 sólo) 2005-2007 ... 4 - Saturn Relay 2005-2007 ... 4 Ensamble del kit - Provisión de unidad central doble DIN ...
Desmontaje del tablero 95-3304 Buick Terraza/Chevy Uplander Pontiac Montana SV6/Saturn Relay 1. Suelte y retire el panel de la moldura que rodea el radio y el control del aire acondicionado. 2. Retire los (8) tornillos de 9/32” para extraer el radio y el control del aire acondicionado A/C del sub tablero.
Desmontaje del tablero 95-3304 Chevrolet Corvette 1. Suelte y retire el interruptor de control de movimiento/la placa decorativa del borde frontal de la tapa de la consola central. (Step 2) 2. Retire los (2) tornillos de 9/32” de debajo de la placa que retiró. (Step 3) 3.
Desmontaje del tablero 95-3304 Hummer H3 2006-2009 1. Suelte y retire el panel de recorte alrededor de la radio y los controles del clima. (Figura A) 2. Retire los (4) tornillos de 9/32” que sostienen el radio. (Figura B) 3. Desconecte y retire el radio.
Ensamble del kit 95-3304 Provisión de unidad central doble DIN 1. Deslice el soporte correspondiente en la placa de la moldura, alineando los orificios de la placa con los ganchos del soporte. (Figura A) 2 Deslice la unidad del radio DDIN en el...
Ensamble del kit 95-3304 Provisión de unidad central 1. Deslice el soporte correspondiente en la placa de la moldura, alineando los orificios de la placa con los ganchos del soporte. (Figura A) 2 Deslice la ISO DIN vertical en el...