1. Manuals
  2. Brands
  3. Echo Manuals
  4. Trimmer
  5. HCAS-2200
  6. Service data

Echo HCAS-2200 Service Data

Hedge trimmer
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
15-21D-01
INTRODUCTION
We are constantly working on technical
improvement of our products. For this reason,
technical data, equipment and design are
subject to change without notice. All
specifications and directions in this SERVICE
DATA are based on the latest products
inf o rma t i o n a v a ila b le a t t h e t im e o f
publication.
INDEX
HCAS-2200
1 SERVICE INFORMATION ............................. 2
1-1 Specification .................................................. 2
1-2 Technical data ................................................ 3
1-3 Torque limits ............................................... 4
1-4 Special repairing materials ......................... 5
1-5 Service limits .............................................. 5
1-6 Special tools ............................................... 6
2 EMISSION ADJUSTMENT GUIDE ............... 7
2-1 General adjusting rules .............................. 7
and H mixture needle ........................................ 7
2-3 Adjusting carburettor .................................. 8
CONTENTS
15-21D-01
Reference No.
R E V I S E D :
2 0 0 6 0 6
ISSUED: 200603
1
1
2
page

Advertisement

Table of Contents
loading

Related Manuals for Echo HCAS-2200

Summary of Contents for Echo HCAS-2200

  • Page 1: Table Of Contents

    HCAS-2200 15-21D-01 CONTENTS INTRODUCTION page 1 SERVICE INFORMATION ......2 We are constantly working on technical 1-1 Specification ..........2 improvement of our products. For this reason, 1-2 Technical data ..........3 technical data, equipment and design are 1-3 Torque limits ..........4 subject to change without notice.

  • Page 2: Service Information

    25.0 - 22.0 (0.98 - 0.86) (Main pipe) Length mm(in) 844 (33.2) Gear case Reduction ratio 3.95 Gear tooth Spiral bevel gear Lubrication Lithium based grease or ECHO LUBE Cutter Type Double reciprocating, double edge blade Length mm(in) 450 (18) Pitch mm(in) 35.0 (1.38)

  • Page 3: Technical Data

    SERVICE INFORMATION HCAS-2200 1-2 Technical data Engine Idling speed r/min 2700 - 3200 Wide open throttle speed r/min 9500 - 11500 Clutch engagement speed r/min 3700 - 4300 Compression pressure MPa (kgf/cm ) (psi) 0.72 (7.3) (104) Ignition system Spark plug gap mm (in) 0.6 - 0.7 (0.024 - 0.028)

  • Page 4: Torque Limits

    ** The torque differences among bolts should not exceed 20 kgf•cm (2N•m, 17in•lbf) on one cylinder or crankcase. 1-4 Special repairing materials Material Location Remarks Grease Drive shaft Gear case Lithium based grease or ECHO LUBE Rewind spring Starter center post Oil seal inner lips Thread locking Starter case Loctite #222, ThreeBond #1342 or equivalent sealant...

  • Page 5: Service Limits

    SERVICE INFORMATION HCAS-2200 1-5 Service limits 5K286 5K263 5K264 5K265 5K266 5K016 5K017 5K267 5K219 5K171 5K071A Description mm (in) Cylinder bore When plating is worn and aluminum can be seen Piston outer diameter Min. 32.10 (1.264) Piston pin bore Max.

  • Page 6: Special Tools

    HCAS-2200 SERVICE INFORMATION 1-6 Special tools Key Part Number Description Used for: 897801-33330 Tachometer PET-1000 Measuring engine speed 363018-00310 Washer Installing crankcase oil seal of starter side 895610-79920 L-hex wrench (4 mm) Removing and installing hex. socket bolts (M5) 897603-23030...

  • Page 7: Emission Adjustment Guide

    SERVICE INFORMATION HCAS-2200 2 EMISSION ADJUSTMENT GUIDE 2-1 General adjusting rules A. Before starting the unit for adjustment, check the following items. 1. The correct spark plug must be clean and properly gapped. 2. The air filter element must be clean and properly installed.

  • Page 8: Adjusting Carburettor

    HCAS-2200 SERVICE INFORMATION 2-3 Adjusting carburettor 1. Start engine and warm it up alternating engine speed between WOT and idle every 5 seconds for 1 minute . 2. Adjust idle mixture needle and obtain maximum idle speed with 2.5 mm blade small screw driver.

Table of Contents