P/N:TCP520BEF0 Service Manual COLOR TELEVISION CHASSIS : CP-520 MODEL : DTY-28A8/28A6/28A7 DTY-2880/28W5 DTY-21U7/21B4 DTY-25G6/25G7 CHASSIS : CP-520A MODEL : DTC-20T2 DTC-21Y1/21Y2 CHASSIS : CP-520F MODEL : DTZ-29U7/U3 DTZ-2881/28W8 DTZ-2481 Caution : In this Manual, some parts can be changed for improving. their performance without notice in the parts list.
CP-520/520A/520F Service Manual DOCUMENT HISTORY VERSION DATE COMMENTS V1.00 12/05/04 Creation of document (Author JS KIM) for project CP520 50Hz TV. DTV R&D Europe...
CP-520/520A/520F Service Manual MAIN FEATURES 1.1 SPECIFICATIONS 1.1.1 GENERAL TV standard PAL - SECAM B/G D/K, PAL I/I, SECAM L/L’ Colour system Tuner PAL, SECAM PAL, SECAM, PAL 60, NTSC M, NTSC 4.43 Sound system NICAM B/G, I, D/K, L,...
CP-520/520A/520F Service Manual Slow Switching TV : 0 to 2V, AV 16/9 : 4.5 to 7V, AV 4/3 : 9.5 to 12V , Impedance > 10 k Green Earth N.C. Green Input 0.7 Vpp 0.1V, Impedance 75 N.C. Red Earth...
CP-520/520A/520F Service Manual SAFETY INSTRUCTION WARNING: Only competent service personnel may carry out work involving the testing or repair of this equipment. X-RAY RADIATION PRECAUTION Excessive high voltage can produce potentially hazardous X-RAY RADIATION. To avoid such hazards, the high voltage must not exceed the specified limit. The nominal value of the high voltage of this receiver is 25-26 KV (20”-21”) or 26 KV (25”...
CP-520/520A/520F Service Manual ALIGNMENT INSTRUCTIONS 3.1 MICROCONTROLLER CONFIGURATION : SERVICE MODE To switch the TV set into service mode please see instruction below. 1 - Select PR. number 91 2 - Adjust sharpness to minimum and exit all menus. 3 – Within 2 seconds press the key sequence : RED - GREEN - menu The software version is displayed beside the word Service, e.g.
CP-520/520A/520F Service Manual 3.4 OPTION 1 FASTEXT VAI bit set Dolby TUBE SVHS3 TUNER OPTIONS Teletext (FLOF) to 1 in Virtual disable 00 = Philips SECAM L 01 = Not used VAI bit set Dolby 10 = Alps FASTEXT TUBE...
CP-520/520A/520F Service Manual 3.6 NVM default setting The purpose of this message, when you change a virgin EEPROM, is to allow to modify the NVM DATA to desired values. 1 - Introduction : The NVM default valus are fixed for the user, but for flexibility in service, these data are stored in NVM and can be changed when the TV set is in a special mode call "NVM EDITOR".
Page 14
CP-520/520A/520F Service Manual NVM DATA CHANGE LIST (hex) CP-520 CP-520F CP-520A No Register Name Address Default 28A8 2880 21U7 2881 29U7 21Y1 20T2 OCP_THRESHOLD 0x58F 0x91 <- <- <- <- <- <- <- DCXO 0x590 0x4E <- <- <- <- <-...
CP-520/520A/520F Service Manual 3.7 TV SET ALIGNMENT 3.7.1 G2 ALIGNMENT - Tune a colour bar pattern. - Find the “G2 – SCREEN” item in service mode. - Adjust screen volume (on FBT) to bring the cursor to central position(Green). 3.7.2 WHITE BALANCE - Select a dark picture and adjust RED BIAS and GRN BIAS to the desired colour temperature.
CP-520/520A/520F Service Manual HOR WIDTH adjust for 93% overscan. PARABOLA CORNER B & CORNER T EW TRAPEZ 3.7.7 AGC - Make sure option bits are correct for the tuner fitted on the chassis (See above how to change option bits).
CP-520/520A/520F Service Manual IC DESCRIPTION 4.1 UOC Series The UOC series combines the functions of a Video Signal Processor (VSP) together with a FLASH embedded TEXT/Control/Graphics -Controller (TCG -Controller) and US Closed Caption decoder. In addition the following functions can be added:...
Page 19
CP-520/520A/520F Service Manual 4.1.3. PINNING QFP 128pin Symbol Short Description P1.5/TX Port 1.5 or UART bus P1.4/RX port 1.4 or UART bus P1.2/INT2 port 1.2 or external interrupt 2 VSSC3 Ground VDDC3 digital supply to core (1.8V) P2.5/PWM4 port 2.5 or PWM4 output P2.4/PWM3...
Page 20
CP-520/520A/520F Service Manual Green output Red output BLKIN black current input BCLIN beam current limiter input 3rd supply for TV processor GND3 ground 3 for TV-processor B/PBIN3 3rd B input / PB input G/YIN3 3rd G input / Y input...
Page 21
CP-520/520A/520F Service Manual AGC sound IF / internal-external AGC for DVB SIFAGC/DVBAGC (2) applications PLLIF IF-PLL loop filter GND2 ground 2 for TV processor QSS intercarrier output / AM output / deemphasis QSSO/AMOUT/AUDEE (front-end audio M (2) out) DECSDEM decoupling sound demodulator...
Page 22
CP-520/520A/520F Service Manual 4.1.4 FEATURES Analogue Video Processing (all versions) · Multi-standard vision IF circuit with alignment-free PLL demodulator · Internal (switchable) time-constant for the IF-AGC circuit · Switchable group delay correction and sound trap (with switchable centre frequency) for the demodulated CVBS signal ·...
Page 23
CP-520/520A/520F Service Manual windows in parallel. · Linear and non-linear horizontal scaling of the video signal to be displayed. Sound Demodulation (all versions) · Separate SIF (Sound IF) input for single reference QSS (Quasi Split Sound) demodulation. · AM demodulator without extra reference circuit ·...
Page 24
CP-520/520A/520F Service Manual · FM overmodulation adaptation option to avoid clipping and distortion Audio Multi Channel Decoder (stereo versions with Audio DSP) · Dolby® Pro Logic® (DPL) (1) · Five channel processing for Main Left and Right, Subwoofer, Centre and Surround. To exploit this feature an external DAC is required.
CP-520/520A/520F Service Manual · 5 PWM (6-bits) outputs for analogue control functions · Remote Control Pre-processor (RCP) · Universal Asynchronous Receiver Transmitter (UART) Data Capture · Text memory up to 10 pages · Inventory of transmitted Teletext pages stored in the Transmitted Page Table (TPT) and Subtitle Page Table (SPT) ·...
CP-520/520A/520F Service Manual all-NPN output stage and standby/mute logic. The TDA8946J comes in a 17-pin DIL-bent- SIL(DBS) power package. 4.2.1 FEATURES § Few external components § Fixed gain § Standby and mute mode § No on/off switching plops § Low standby current §...
CP-520/520A/520F Service Manual 4.3 TDA8358J VERTICAL AMPLIFIER The TDA8358J are power circuit for use in 90° and 110° colour deflection systems for field frequencies of 25 to 200Hz field frequencies, and for 4:3 and 16/9 picture tubes. The IC contains a vertical deflection output circuit, operating as a high efficiency class G system.
Page 29
CP-520/520A/520F Service Manual Pinning Symbol Description Positeve vertical input Negative vertical input Supply voltage OUTB Vertical output voltage B INEW East-west input voltage VGND Vertical ground EWGND East-west ground OUTEW East-west output voltage Flyback supply voltage OUTA Vertical output voltage A...
CP-520/520A/520F Service Manual 4.4 TDA6107AJF The TDA6107AJF includes three video output amplifiers and is intended to drive the three cathodes of a colour CRT directly. The device is contained in a plastic DIL-bent-SIL 9-pin medium power(DBS9MPF) package, and uses high-voltage DMOS technology.
CP-520/520A/520F Service Manual Block diagram TDA6107AJF 4.5 24WC16 - 16 KB EEPROM Features : § 16 Kbit serial I2C bus EEPROM § 400KHz I2C Bus Compatible § supply voltage : 1.8 V to 6.0 V § Low Power CMOS Technology §...
CP-520/520A/520F Service Manual 4.6 STR - F6653 4.6.1 GENERAL DESCRIPTION The STR-F6653 is an hybrid IC with a build-in MOSFET and control IC, designed for flyback converter type switch mode power supply applications. 4.6.2 FEATURES § Small SIP fully isolated moulded 5 pins package §...
CP-520/520A/520F Service Manual 4.6.4 PIN DESCRIPTION NAME SYMBOL DESCRIPTION O.C. Input of over current detection signal and feedback Overcurrent feedback P/E.B. signal Source Mosfet source Drain Mosfet drain Supply Input of power supply for control circuit Ground Ground 4.6.5 CONTROL PART - ELECTRICAL CHARACTERISTICS...
CP-520/520A/520F Service Manual 4.6.6 MOSFET ELECTRICAL CHARACTERISTICS IC PIN RATING DESCRIPTION NUMBER SYMBOL MIN. TYPE UNIT Drain-to-source break down voltage Drain leakage current On-resistance (on) 1.95 Switching time noec Thermal resistance 0.95 DTV R&D Europe...
CP-520/520A/520F Service Manual 5.2 FUNCTIONAL DESCRIPTION OF VIDEO PROCESSOR 5.2.1 Vision IF amplifier The vision IF amplifier can demodulate signals with positive and megative modulation. The PLL demodulator is completely alignment-free. The VCO of the PLL circuit is internal and the grequency is fixed to the required value by using the clock ftequency of the TCG u-Controller as a reference.
CP-520/520A/520F Service Manual applied to obtain sufficient selectivity (the sound input can be activated by means of the setting of CMB2-CMB0 bits in subaddress 4AH). The setting to the wanted frequency is realised by means of the control bits FMA, FMB and FMC in the control bit 33H.
CP-520/520A/520F Service Manual The Ics have 3 inputs for external CVBS signals. All CVBS inputs can be used as Y input for the insertion of Y/C signals.However, the CVBS(Y)2 input has to be combined with the C3 input. It is possible to add and extra CVBS(Y/C) input via the pins which are intended to be used for YUV interface (or RGB/YPrPb input).
CP-520/520A/520F Service Manual available on one of the other CVBS inputs.In this condition the connections between the vision IF amplifier and the synchronisation circuit can be switched on and off by means of the VDX bit. The VDXEN bit must be set to “1” for this mode.
CP-520/520A/520F Service Manual The circuit contains the following picture improvement features: n Peaking control circuit. The peaking function can be activated for all incoming CVBS, Y/C and RGB/YPrPb signals. Various parameters of the peaking circuit can be adapted by means of the I2C-bus.
CP-520/520A/520F Service Manual The SECAM decoder contains an auto-calibrating PLL demodulator which has two references, viz: the divided reference frequency (obtained from the-Controller) which is used to tune the PLL to the desired free-running frequency and the bandgap reference to obtain the correct absolute value of the output signal.
Page 42
CP-520/520A/520F Service Manual WPR(GB) ‘0’ Max 64 ‘0’ ‘0’ ‘0’ Max 60 CCC-gain Max 126 R(GB)-gain Max 126 The setting of the gain registers of the 3 channels can be stored during switch off and can be loaded again during switch-on so that the drive conditions are maintained.
CP-520/520A/520F Service Manual 5.2.11 I2C-BUS USER INTERFACE DESCRIPTION The UOC III series is fully controlled via the I2C-bus. Control is exercised by writing data to one or more internal registers. Status information can be read from a set of info registers to enable the controlling microcontroller determine whether any action is required.
CP-520/520A/520F Service Manual n Automatic decoder configuration and signal routing depending on the selected or detected standard n FM overmodulation adaptation option to avoid clipping and distortion 5.3.1 Supported standards The multistandard capability of the TV Sound Processor covers all terrestrial TV sound standards, FM Radio and satellite FM.
CP-520/520A/520F Service Manual PARAMETER A2/A2* A2+ (KOREA) Pilot frequency 54.6875kHz = 3.5 x line freq. 55.0699 kHz = 3.5 x line freq. Stereo identification frequency 117.5 Hz = line freq / 133 149.9 Hz = line freq / 105 Dual indetification frequency 274.1 Hz = line freq / 57...
CP-520/520A/520F Service Manual intercarrier and an external second SIF(2NDSIFEXT), e.g. an intercarrier coming from a PIP frontend. In other applications a 10.7MHz radio IF or satellite FM may be connected to this input. The selected SSIF passes some anti alias filtering, is amplified in an AGC amplifier (SSIF AGC) and is then converted from analogue to digital (SSIF ADC).
CP-520/520A/520F Service Manual decoding is done in the DEMDEC block of the Sound DSP. The DEMDEC processing will be described in the next chapter. The audio signals (AUD ADC IN) from the analogue crossbar pass the audio ADC and are fed directly into the AUDIO part of the Sound DSP like the I2S signals, which is coming from I2S processing hardware.
Page 48
CP-520/520A/520F Service Manual output signal of the first demodulator can be used for further demodulation of multiplex signals used in the BTSC, EIAJ and FM Radio standards. FMIDENTIFICATION The identification of the FM sound mode is performed by AM synchronous demodulation of the pilot signal and narrow-band detection of the identification frequencies.
Page 49
CP-520/520A/520F Service Manual number of sound sample errors, resulting from parity checking, that occurred in the past 128ms period. The Bit Error Rate (BER) can be calculated using the following equation; During NICAM mode a switchable J17 de-emphasis is supplied.