Installation And Connections - Harman Kardon AVR 445 Owner's Manual

Harman-kardon audio/video receiver owner's manual avr 445
Table of Contents

Advertisement

System Installation
After unpacking the unit, locating it in a place with ade-
quate ventilation and placing it on a solid surface capable
of supporting its weight, you will need to make the con-
nections to your audio and video equipment.
IMPORTANT NOTE: For your personal safety and to
avoid possible damage to your equipment and speakers,
it is always good practice to turn off and unplug the AVR
and ALL source equipment from the AC output before
making any audio or video system connections.
Audio Equipment Connections
We recommend that you use high-quality interconnect
cables when making connections to source equipment
and recorders to preserve the integrity of the signals.
1. Connect the analog output of a CD player to the
CD Audio Inputs
.
NOTE: If your CD player has both fixed and variable
audio outputs, it is best to use the fixed output unless
you find that the input to the receiver is so low that the
sound is noisy, or so high that it is distorted.
2. Connect the analog Play/Out jacks of a cassette
deck, MD, CD-R or other audio recorder to the
Tape Inputs
. Connect the analog Record/In
jacks on the recorder to the Tape Outputs
on the AVR 445.
3. Connect the output of a digital source such as
a CD or DVD changer or player, a video game, a
digital satellite receiver, an HDTV tuner or digital
cable set-top box or the output of a compatible
computer sound card to the Optical and Coaxial
KL.
Digital Audio Inputs
4. Connect the coaxial or optical Digital Audio Outputs
on the rear panel of the AVR 445 to the match-
ing digital input connections on a CD-R, MiniDisc or
other digital recorder.
5. Assemble the AM loop antenna supplied with the
unit so that the tabs at the bottom of the antenna
loop snap into the holes in the base. Connect it to
the AM Antenna Connections
.
6. Connect the supplied FM antenna to the FM
Antenna Jack
. The FM antenna may be
an external roof antenna, an inside powered or
wire-lead antenna or a connection from a cable
TV system. If the antenna or connection uses
300-ohm twin-lead cable, you must use an optional
300-ohm-to-75-ohm adapter to make the
connection.

INSTALLATION AND CONNECTIONS

7. Connect the front, center, surround and surround
back speaker outputs
tive speakers.
To ensure that all the audio signals are carried to your
speakers without loss of clarity or resolution, we sug-
gest that you use high-quality speaker cable. Many
brands of cable are available and the choice of cable
may be influenced by the distance between your
speakers and the receiver, the type of speakers you
use, personal preferences and other factors. Your
dealer or installer is a valuable resource to consult in
selecting the proper cable.
Regardless of the brand of cable selected, we recom-
mend that you use cable with a gauge of 14 or smaller.
Remember that when specifying cable, the lower the
number, the thicker the cable.
Cable with a gauge of 16 may be used for short runs
of less than 10 feet. We do not recommend that you
use cables with an AWG equivalent of 18 or higher,
due to the power loss and degradation in performance
that will occur.
Cables that are run inside walls should have the appro-
priate markings to indicate listing with UL, CSA or other
appropriate testing agency standards. Questions about
running cables inside walls should be referred to your
installer or a licensed electrician who is familiar with
the NEC and/or the applicable building codes in
your area.
When connecting wires to the speakers, be certain
to observe proper polarity. Note that the positive (+)
terminal of each speaker connection has a specific color
code, as noted on page 8. However, most speakers still
use a red terminal for the positive (+) connection.
Connect the "negative" or "black" wire to the same
terminal on both the receiver and the speaker.
NOTE: While most speaker manufacturers adhere to
an industry convention of using black terminals for
negative and red ones for positive, some may vary
from this configuration. To ensure proper phase and
optimal performance, consult the identification label on
your speaker or the speaker's manual to verify polarity.
If you do not know the polarity of your speaker, ask
your dealer for advice before proceeding, or consult
the speaker's manufacturer.
We also recommend that the length of cable used
to connect speaker pairs be identical. For example,
use the same length piece of cable to connect the
front-left and front-right or surround-left and sur-
round-right speakers, even if the speakers are a
different distance from the AVR 445.
8. Connections to a subwoofer are normally made via
a line-level audio connection from the Subwoofer
Output
to the line-level input of a subwoofer
with a built-in amplifier. When a passive subwoofer
is used, the connection first goes to a power
amplifier, which will be connected to one or more
to the respec-
subwoofer speakers. If you are using a powered
subwoofer that does not have line-level input con-
nections, follow the instructions furnished with the
speaker for connection information.
9. If an external audio source such as a DVD-Audio,
SACD or high-definition optical disc player with 5.1
or 7.1 analog audio outputs is part of your system,
connect the outputs of the source to the 8-Channel
Direct Inputs
Analog Video Equipment Connections
Analog video components are connected in the same
manner as audio components. Again, the use of high-
quality interconnect cables is recommended to preserve
signal quality.
1. Connect the Video Play/Out jacks of a standard
(composite) video (or S-video outputs of a digital
video) recorder or conventional VCR to the Video 1
Video Inputs
Record/In jacks from that device to the Video 1
Video Outputs
2. Connect the analog Audio Left/Right Play/Out jacks
of the device connected to the Video 1 Inputs to
the Video 1 Audio Inputs
the analog Audio Left/Right Record/In jacks from
that device to the Video 1 Audio Outputs
the AVR. If the device has a digital audio output,
connect it to one of the Coaxial
digital audio inputs.
3. Connect the Play/Out jacks of a standard (composite)
video or (S-video outputs of a digital video) playback
source such as a set-top box or video game console
to the Video 2 Video Inputs
Inputs
. If the device has analog component
video (Y/Pr/Pb) outputs, connect them to one of
the Component Video Inputs
4. Connect the analog audio outputs from the source
to the matching Video 2 Audio Inputs
Video 3 Audio Inputs
tal audio output, connect it to one of the Coaxial
or Optical
5. If any of the video source devices has analog
component video (Y/Pr/Pb) outputs, but not HDMI,
connect them to Component Video Inputs
The chart on page 59 has the default settings for
various source devices, but you may make any
connection and change the configuration setting
using the IN/OUT SETUP menu, as
described on page 23.
6. The default video connection for a DVD player is to
use the Component Video Input 3 Jacks
the AVR, but you may change this assignment in
the IN/OUT SETUP menu (see page 23).
A DVD player's composite and S-video outputs may
also be connected to the DVD Video Inputs
Only one connection type is required.
INSTALLATION AND CONNECTIONS
.
on the AVR 445. Connect the
on the AVR.
on the AVR. Connect
on
or Optical
or Video 3 Video
.
or
. If the device has a digi-
digital audio inputs.
.
on
.
17

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents