Table of Contents
Advertisement
Quick Links
EMPIRE
EMPIRE
Comfort Systems
The Studio Series Direct Vent Zero
Clearance Gas Fireplace Heater
WARNING
WARNING: If the information in these instructions
are not followed exactly, a fire or explosion may re-
sult causing property damage, personal injury or
loss of life.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use
any phone in your building.
•
Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
•
If you cannot reach your gas supplier, call the
fire department.
— Installation and service must be performed by a
qualified installer, service agency or the gas sup-
plier.
INSTALLATION INSTRUCTIONS
GAS-FIRED
HOT GLASS
WILL
CAUSE BURNS.
DO NOT TOUCH
GLASS
UNTIL COOLED.
NEVER
ALLOW CHILDREN
TO TOUCH GLASS.
AND
OWNER'S MANUAL
GAS FIREpLACE HEATER
MILLIvOLT STANDING pILOT
Installer:
Consumer: Retain this manual for future reference.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA only)
or mobile home, where not prohibited by state or local
codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certified
kit is used.
WARNING: If not installed, operated and maintained
in accordance with the manufacturer's instructions,
this product could expose you to substances in fuel or
from fuel combustion which can cause death or seri-
ous illness.
DIRECT vENT
MODEL SERIES
Dvp36Dp31(N,p)-1
DIRECT IGNITION
Dvp36Dp51N-1
INTERMITTENT pILOT
Dvp36Dp71(N,p)-1
REMOTE RF MODELS
Dvp36Dp91(N,p)-2
UL FILE NO. MH30033
Leave this manual with the appliance.
Page 1
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Empire Comfort Systems Studio DVP36DP31N-1
Summary of Contents for Empire Comfort Systems Studio DVP36DP31N-1
-
Page 1: Installation Instructions
INSTALLATION INSTRUCTIONS EMPIRE EMPIRE OWNER’S MANUAL Comfort Systems The Studio Series Direct Vent Zero DIRECT vENT Clearance Gas Fireplace Heater GAS FIREpLACE HEATER MODEL SERIES MILLIvOLT STANDING pILOT Dvp36Dp31(N,p)-1 DIRECT IGNITION Dvp36Dp51N-1 INTERMITTENT pILOT GAS-FIRED Dvp36Dp71(N,p)-1 REMOTE RF MODELS Dvp36Dp91(N,p)-2 WARNING UL FILE NO. -
Page 2: Table Of Contents
TABLE OF CONTENTS Section page Important Safety Information ................................3 Safety Information for Users of LP Gas ............................. 4 Requirements for Massachusetts ................................5 Introduction ......................................6 Specifications ....................................... 7 Fireplace Dimensions ................................... 7 Clearances ......................................8 Locating Fireplace ....................................8 Gas Supply ...................................... -
Page 3: Important Safety Information
IMpORTANT SAFETY INFORMATION Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly. DO NOT OPERATE THIS APPLIANCE WITHOUT GLASS FRONT PANEL INSTALLED • If this appliance is installed directly on carpeting, placed on or near the appliance. tile or other combustible material other than wood •... -
Page 4: Safety Information For Users Of Lp Gas
SAFETY INFORMATION FOR USERS OF Lp GAS Propane (LP-Gas) is a flammable gas which can cause fires by point with the members of your household. Someday and explosions. In its natural state, propane is odorless and when there may not be a minute to lose, everyone’s safety colorless. -
Page 5: Requirements For Massachusetts
REqUIREMENTS FOR MASSACHUSETTS For all side wall horizontally vented gas fueled equipment installed 3. SIGNAGE. A metal or plastic identification plate shall be in every dwelling, building or structure used in whole or in part permanently mounted to the exterior of the building at a for residential purposes, including those owned or operated by the minimum height of eight (8) feet above grade directly in line Commonwealth and where the side wall exhaust vent termination... -
Page 6: Introduction
• Installation of any damaged fireplace or vent system component. • Modification of the fireplace or direct vent system. • Installation other than as instructed by Empire Comfort Systems, State of Massachusetts: The installation must be made by Inc. a licensed plumber or gas fitter in the Commonwealth of •... -
Page 7: Specifications
SpECIFICATIONS Dvp36 Nat Models Remote Control Description Input Btu/hr Maximum 25,000 Options & Accessories Btu/hr Minimum (millivolt only) 18,000 FRBC Millivolt Battery Remote ON/OFF KWH (Maximum) FRBTC Millivolt Battery Remote Thermostat (Minimum) Millivolt Wireless Wall Thermostat Orifice #41 (P-256) Millivolt Reed Switch Wall Thermostat Air Shutter Opening 1/8"... -
Page 8: Clearances
CLEARANCES Mantel Chart (Figure 3) Clearance to Combustibles Back 0" (0 mm) Side 0" (0 mm) Floor 0" (0 mm) Top Stand-off 0" (0 mm) Top Framing Edge 3" (76 mm) SEE MANTLE CHART FOR MAXIMUM MANTLE DEPTH 2" x 4" HEADER STAND OFF 3"... -
Page 9: Gas Supply
GAS SUppLY Installing a New Main Gas Cock he gas pipeline can be brought in through the right or left side of Each appliance should have its own manual gas cock. the appliance. Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/CGA-B149 (.1 or .2) installation code. -
Page 10: Rear Vent Conversion
REAR VENT CONVERSION VERTICAL VENTING Lp and Nat models Note: Discard insulation HORIZONTAL VENTING & retainer when venting off Nat models only top of fireplace. INLET VENT Note : Discard insulation COVER PLATE & retainer when using vertical venting off Note : It is recommended that the FLUE COVER PLATE flue cover plate tab be pulled... -
Page 11: Installation
INSTALLATION Framing and Finishing vent pipe Clearance 1. Choose unit location. Note: Maintain one inch (1") of clearance around vertical vent pipe. 2. Frame in fireplace with a header across the top. It is important to See Figures 9A and 9B. For horizontal vent, maintain a minimum allow for finished face when setting the depth of the frame. - Page 12 INSTALLATION (continued) Note: For finishing to top of fireplace, refer to Figure 11. Flush Mount Mantel Installation (Figure 10) The fireplace must extend 3/4" beyond finished wall surface when using a flush mount mantel. Refer to Figure 10 to locate nailing flanges on fireplace sides.
- Page 13 Flush Wall Installation Attention: Cold climate installation recommendation: When installing this unit against a non-insulated exterior wall, it is FINISHED WALL recommended that the outer walls be insulated to conform to applicable insulation codes. 3” OF NON-COMBUSTIBLE MATERIAL NONCOMBUSTIBLE MATERIAL (INSTALLATION IS OPTIONAL) Vent Runs (Figures 14, 15, 16, 17, and 18) In planning the installation for the fireplace, it is necessary to install...
- Page 14 INSTALLATION (continued) HoRIzonTAL onLY, STRAIGHT oUT THE BACK CORNER INSTALLATION vERTICAL, 90° ELBOW TO HORIzONTAL OUT THE WALL " A" PIPE LENGTH WALL FIRESTOP/ THIMBLE VENT VENT CAP WALL FIRESTOP/ THIMBLE Nat models only "A" "B" Lp and Nat models 6"...
-
Page 15: Venting Fireplace - Top (Lp And Nat Models)
vENTING FIREpLACE - TOp (Lp & NAT MODELS) venting Graph (Dimensions in Feet) To Use the vent Graph (Figure 19) 1. Determine the height of the center of the horizontal TOP EXIT - VERTICAL AND HORIZONTAL TERMINATION vent pipe. Using this dimension on the Sidewall Vent (DIMENSIONS IN FEET) Graph, locate the point it intersects with the slanted graph line. - Page 16 vENTING FIREpLACE - TOp (continued) Installation of Flue Heat Shield Remove flue insulation. Remove (2) screws on outside of inlet vent adapter. See Figure 20. 3. Lift top shield placing flue heat shield around flue. 4. Replace (2) screws on outside of inlet vent adapter. See Figure 21.
- Page 17 vENTING FIREpLACE - TOp (continued) Below Grade Installation When it is not possible to meet the required vent terminal clearances of 12" (305mm) above grade level, a snorkel kit is recommended. It allows installation depth down to 7" (178mm) below grade level. The 7"...
- Page 18 vENTING FIREpLACE - TOp (continued) minimum Lp and Nat models Figure 26 Figure 25 Lp and Nat models MINIMUM HOLE LOCATION DIMENSIONS FOR THROUGH THE WALL HORIZONTAL INSTALLATIONS WITH 90 DEGREE ELBOW OFF TOP OF FIREPLACE FIREpLACE HARD ELBOW DIMENSIONS SERIES "A"...
-
Page 19: Examples - Top Vent Run
EXAMpLES - TOp vENT RUN Example H2 3ft, H3 1ft = 4ft (90° + 90° + 90°) = 6ft V1 = 21ft H = 10ft V = 21ft Lp and Nat models Figure 29 Lp and Nat models Figure 28 Lp and Nat models Figure 30 26408-0-1009... -
Page 20: Dvvk-4Fv Direct Vent Termination Kit
DVVK-4FV DIRECT VEnT TERMInATIon KIT Installation Instructions This termination kit can only be used with Empire Comfort Systems direct vent fireplaces listed for use with DVVK-4FV Vertical Flex Vent Kit. Please review the instructions packaged with your fireplace and verify the fireplace model number. - Page 21 pRE-INSTALLATION INFORMATION: Items Required For Installation: Tools Building Supplies Phillips Screwdriver Framing Materials Hammer Wall Finishing Materials Saw and/or saber saw Caulking Material (Noncombustible) Level Support Strap supplies Measuring Tape Electric Drill and Bits Pliers Square Tin Snips Before You Start: Plan your installation.
- Page 22 DVVK-4FV DIRECT VEnT TERMInATIon KIT (continued) Step-By-Step Installation For Flex DV Kit Unpack vent components and check all items for shipping 5. Next, determine the location for the cutout in the roof open- damage. ing. This opening must be large enough to provide a mini- For this venting system to operate as designed it is depen- mum 1”...
- Page 23 10. With the flex vent assembly and the 48” long hard pipe com- 13. Now the pre-assembled vent system may be carried to the ponents laid out on the floor, begin securing these parts to- roof, then lowered through the roof cutout opening (see step gether.
- Page 24 DVVK-4FV DIRECT VEnT TERMInATIon KIT (continued) 17. To attach the vent connections at the fireplace, be sure the 7” 21. An additional storm collar band is provided in kit that may be diameter adapter collar has been installed per step 3. Apply used as an attic insulation shield.
- Page 25 DVVK-4FV DIRECT VEnT TERMInATIon KIT (continued) Vertical Termination Storm 4' Long Rigid Pipe Collar Roof Flashing Adjustable Roof Jack Roof Assembly Exterior Clearance to Combustibles Required From Vent Pipe Clamps At Flue & Inlet Vent Connections Adjustable Storm Collar (Use TO Firestop/Thimble Keep Insulation Out Of Assembly...
-
Page 26: Dvvk-4Fv Direct Vent Termination Kit
DVVK-4FV DIRECT VEnT TERMInATIon KIT (continued) Vertical Flex Termination Kit Item quantity Number Item Description Repair part No. Supplied 4”/7” Vertical Termination Cap MF100038 Roof Support Kit MF100503 2 Ply Alum Flex 4” Diameter by 6 ft. MF04ALA2F006 2 Ply Alum Flex 7” Diameter by 6 ft. MF07ALA2F006 4”/7”... -
Page 27: Venting Fireplace - Rear (Nat Models Only)
vENTING FIREpLACE - REAR (NAT GAS MODELS ONLY) venting Graph (Dimensions in Feet) To Use the vent Graph (Figure 38) 1. Determine the height of the center of the REAR EXIT - VERTICAL AND HORIZONTAL TERMINATION horizontal vent pipe. Using this dimension on (DIMENSIONS IN FEET) the Sidewall Vent Graph, locate the point it intersects with the slanted graph line. -
Page 28: Examples - Rear Vent Run
EXAMpLES - REAR vENT RUN Model Maximum Pipe Length H1 DVP36 24" Nat models only Figure 41 Nat models only Figure 39 Model Maximum Pipe Length H1 DVP36 24" Nat models only Nat models only Figure 42 Figure 40 Page 28 26408-0-1009... -
Page 29: Dvvk-4Re Vent Kit Installation Instructions
DVVK-4RE VEnT KIT InSTALLATIon InSTRUCTIonS CAUTION: Sharp edges, use protective gloves when NOTE: SPACING FLANGE INSTALLED TO TOPSIDE installing. Tools Needed for Installation: Sheet metal snips 5/16” nut driver Phillips head screwdriver - #2 High temperature sealant or furnace cement rated for continuous use at 1,000 F minimum 11”... - Page 30 DVVK-4RE VEnT KIT InSTALLATIon InSTRUCTIonS (continued) 7. Remove outside mounting plate with tube attached from wall. Mark and cut the extra length of the 6 5/8” (168mm) diameter VINYL SIDING KIT DV822 tube from the opposite end. Do not crimp or enlarge tube. OUTSIDE MOUNTING 8.
- Page 31 DVVK-4RE VEnT KIT InSTALLATIon InSTRUCTIonS (continued) Follow correct option according to venting method. Connecting to Rigid vent System If the air inlet and flue outlet tubes are to be connected to a rigid Connecting Directly to Fireplace venting system (and not directly to the back of the unit), then do If the air inlet and flue outlet tubes are to be connected directly to not use the gasket provided.
-
Page 32: Dvvk-4F Flex Vent Instructions - Top Vent Only
DVVK-4F FLEX VEnT InSTRUCTIonS - ToP VEnT onLY The DVVK-4F FLEX VEnT KIT includes the following components: • (1) Horizontal Termination Cap • (1) 7" diameter Outer Vent adapter collar • (1) 4-foot section of Flex vent with spacers (4" flue/7" outer •... -
Page 33: Termination Clearances
TERMINATION CLEARANCES Termination clearance for buildings with combustible and noncombustible exteriors. Figure 48 vertical Sidewall Installations Important! Minimum clearance between vent pipes and combustible materials is three (3") (76mm) on top, and (1") (25mm) on bottom and sides. Important! When vent termination exits through foundation less than 20" below siding outcrop, the vent pipe must extend outward so that the horizontal vent terminal is located flush to, or beyond the outcrop siding. -
Page 34: Vent Clearances
vENT CLEARANCES Figure 49 *Clearance above grade, veranda, porch, deck or balcony clearance to non-mechanical air supply inlet to building or [*12 inches (30cm) minimum] the combustion air inlet to any other appliance [*12 inches (30cm) minimum for appliances ≤ 100,000 Btuh (30 kW) clearance to window or door that may be opened [*12 inches (30cm) minimum for appliances <... -
Page 35: Vent System Identification
45° ELBOW ROOF FLASHING TWO 90° ELBOWS) 90° ELBOW Special venting Components (Simpson Duravent) See Empire Comfort Systems Retail Price List for Simpson Duravent part CEILING FIRESTOP numbers and pricing. Special DV Vent Kits WALL STRAP Available from Empire Comfort Systems, Inc. dealers. -
Page 36: Framing And Finishing
FRAMING AND FINISHING Installing Support Brackets (Figure 51) A horizontal pipe support MUST BE used for each 3 feet of horizontal run. The pipe supports should be placed around the pipe and nailed in place to framing members. There MUST BE a 3 inch clearance to combustibles above 6 5/8 inch diameter pipe and elbows and 1 inch clearance on both sides and bottom of 6 5/8 inch pipe to 10”... -
Page 37: Framing And Finishing
FRAMING AND FINISHING (continued) Figure 53 Figure 55 See Horizontal Termination Page 38 and vertical Termination Page 39-40. Figure 54 26408-0-1009 Page 37... -
Page 38: Horizontal Termination
HORIzONTAL TERMINATION NOTE: Termination cap should pass through the wall firestop SNORKEL from the exterior of the building. Adjust the termination cap to its final exterior position on the building. WARNING: Termination cap must be positioned so that arrow is pointing up. Attach the termination cap with the four wood screws provided. -
Page 39: Vertical Termination
vERTICAL TERMINATION Locate and mark the center point of the venting pipe. Using a nail When terminating the vent cap near an exterior wall or overhang, maintain minimum clearances as shown in Figure 59. on the underside of the roof and drive this nail through this center point. -
Page 40: Vertical Termination
All damaged gaskets on the glass frame assembly and combustion chamber must be replaced by a qualified service person. If damage occurs to the combustion chamber, it must be replaced by a qualified service person. Contact Empire Comfort Systems, Inc. for replacement parts. Page 40... -
Page 41: Log Placement - 4 Log Set
LoG PLACEMEnT (4 LoG SET) Before you begin: This fireplace is supplied with a set of four ceramic fiber logs. Do not handle these logs with your bare hands. Always wear gloves to prevent skin irritation from ceramic fibers. After handling logs, wash your hands gently with soap and water to remove any traces of fiber. -
Page 42: Operating Instructions
OpERATING INSTRUCTIONS 750 Millivolt System Initial Lighting The standing pilot (750 millivolt system) is a continuous burning Upon completing the gas line or turning the gas valve on after it pilot. The pilot remains ON even when the main burner is OFF. has been in the “OFF”... - Page 43 OpERATING INSTRUCTIONS (continued) STANDING pILOT OpERATING INSTRUCTIONS Installation of Remote Receiver REMOTE/OFF/ON Switch Place remote receiver on the floor of fireplace behind the louver The fireplace is equipped with a REMOTE/OFF/ON switch. as far forward as possible. A wire harness is attached to the REMOTE/OFF/ON switch. Attention: The Velcro loop and hook are not necessary in this The red, black and green (wires) female push-ons attach to the installation but can be used to secure remote receiver.
-
Page 44: Standing Pilot Wiring Diagram
STANDING pILOT WIRING DIAGRAM (OPTIONAL) THERMOSTAT (OPTIONAL) WALL SWITCH Figure 67 Page 44 26408-0-1009... -
Page 45: Standing Pilot Lighting Instructions
STANDING pILOT LIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. •... -
Page 46: Standing Pilot Troubleshooting
STANDING pILOT TROUBLESHOOTING With proper installation and maintenance, your new Direct vent Gas Fireplace will provide years of trouble-free service. If you do experience a problem, refer to the Trouble Shooting Guide below. This guide will assist a qualified service person in the diagnosis of problems and the corrective action to be taken. -
Page 47: Direct Ignition Wiring Diagram
DIRECT IGNITION WIRING DIAGRAM GAS VALVE SPARK IGNITOR VALVE DE GAZ (OPTIONAL) WALL SWITCH OR THERMOSTAT ÉTINCELLE ALLUMER INTERRUPTEUR MURAL (FACULTATIVE) CONTROL MODULE (OPTIONAL) REMOTE CONTROL AUTORITÉ MODULE RECEIVER 120V (FACULATIVE) CONTROLE E DISTANCE DU RECEPTEUR 120 VAC LINE BLACK NOIR 120 VAC RTN BLACK NOIR WHITE BLANC... -
Page 48: Direct Ignition Lighting Instructions
DIRECT IGNITION LIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXpLOSION MAY RESULT CAUSING pROpERTY DAMAGE, pERSONAL INJURY, OR LOSS OF LIFE. A. BEFORE LIGHTING smell all around the appliance area B. -
Page 49: Initial Start Up Gas Line Purge
INITIAL START UP GAS LINE PURGE NOTE: UNIT MUST BE pROpERLY GROUNDED FOR ELECTRONIC IGNITION TO FUNCTION. On initial installation, or after extended periods where the fireplace has not been used, gas lines may require purging. The installer or qualified service person may use the following purge procedures to prevent the delays that would be caused by waiting for the lockout periods between tries for ignition. -
Page 50: Direct Ignition Propane/Lp Gas Conversion
DIRECT IGNITION PROPANE/LP GAS CONVERSION The conversion shall be carried out in accordance with the 12. Install propane/LP main burner orifice marked 1.55 mm. requirements of the provincial authorities having jurisdiction Important: Failure to install the correct orifice will result in and in accordance with the requirements of the CSA B149.2 unit over-firing that could overheat the appliance and result installation code (Canada) and with the requirements of the... -
Page 51: Direct Ignition Propane/Lp Gas Conversion
DIRECT IGNITION PROPANE/LP GAS CONVERSION Maxitrol valve Conversion Model AIR SHUTTER BURNER ORIFICE SETTINGS Opening "A" Propane/LP Orifice DVP36 FULL OPEN 1.55 mm REGULATOR FITTING NOTE: STAMPED WITH GAS TYPE SET FOR USE Figure 70 Figure 69 26408-0-1009 Page 51... -
Page 52: Intermittent Pilot Operating Instructions
INTERMITTENT pILOT OpERATING INSTRUCTIONS The intermittent pilot (120/24 volt system) is ON when the main Provided on the intermittent pilot wiring harness are two (2) stripped and bare wires that are labeled THERMOSTAT. The wires will be burner is ON. When the main burner is OFF the intermittent pilot used for attachment of 24 volt thermostat, optional FWS wall switch is OFF. -
Page 53: Intermittent Pilot Lighting Instructions
INTERMITTENT pILOT LIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance is equipped with an ignition device •... -
Page 54: Intermittent Pilot Troubleshooting
A. Turn the thermostat to its lowest setting. B. Wait one minute. The Service Department at Empire Comfort Systems, Inc. may be As you do Steps 4 and 5, watch for points where operation contacted to assist in servicing furnace. - Page 55 INTERMITTENT pILOT TROUBLESHOOTING (continued) spark generator and energizes the second main valve operator. The Safety Lockout second main valve opens and gas flows to the main burner, where S8600H provides 100 percent shutoff, or safety lockout. A timer it is ignited by the pilot burner. The flame current also holds the starts timing the moment the trial for ignition starts.
- Page 56 INTERMITTENT pILOT TROUBLESHOOTING (continued) Important WARNING 1. The following service procedures are provided as a general When performing the following steps, do not touch stripped guide. end of jumper or SPARK terminal. The ignition circuit 2. Meter readings between gas control and ignition module must generates 13,000 volts at 25 pf load and electrical shock be taken within the trial for ignition period.
- Page 57 INTERMITTENT pILOT TROUBLESHOOTING (continued) 26408-0-1009 Page 57...
- Page 58 INTERMITTENT pILOT TROUBLESHOOTING (continued) Green LED Status Codes Green LED Flash Code (X + Y) Indicates Next System Action Recommended Service Action No “Call for Heat” Not applicable None Flash Fast Startup-Flame sense calibration Not applicable None Heart Beat Normal operation Not applicable None Recycle...
-
Page 59: Rf Operating Instructions
RF OpERATING INSTRUCTIONS RF VALVE oPERATIon (AF-4040 Electronic Gas Valve sys- 2. When the remote/off switch is in the OFF position the appli- tem only) ance will operate from an appliance mounted rocker switch Please refer to the separate instructions for detailed operation and (#3) or optional wall switch connected to the two (2) BROWN programming of the Multi-function Remote Control. -
Page 60: Rf Maintenance
RF MAINTENANCE INSTRUCTIONS MAINTENANCE TROUBLESHOOTING Maintenance frequency must be determined individually for each IMPORTANT: All service and trouble-shooting procedures should application. Some considerations are: be performed by an experienced qualified service technician. • Exposure to water, dirt, chemicals and heat can damage the If the pilot will not stay lit: gas control and shut down the control system. -
Page 61: Rf Wiring Diagram
RF WIRING DIAGRAM BLOWER BATTERY BACK-UP 120V EXTENSION LIGHT TRANSFORMER MODULE (OPTIONAL) ON/OFF BROWN SWITCH WHITE GREEN GAS CONTROL ORANGE VALVE POWER Stepper PILOT Motor MAIN (GND) PILOT ELECTRONIC WHITE CONTROL MODULE ORANGE JUNCTION BOX Note: For "RF" Fireplace models with Premium Multi-Function Remote Control, Refer to the separate instructions for operation of the remote control system. -
Page 62: Rf Lighting Instructions
RF STANDING pILOT LIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXpLOSION MAY RESULT CAUSING pROpERTY DAMAGE, pERSONAL INJURY, OR LOSS OF LIFE. A. This appliance has a pilot which must be lighted by C. -
Page 63: Maintenance And Service
MAINTENANCE AND SERvICE WARNING: pLEASE NOTE 1. The use of substitute glass will void all product warranties. It is normal for appliances fabricated of steel to give off 2. Care must be taken to avoid breakage of the glass. some expansion and/or contraction noise during the start 3. -
Page 64: Maintenance And Service
MAINTENANCE AND SERvICE Glass Removal and Replacement (Figures 75 and 76) Remove decorative front doors (where applicable) by opening and lifting straight up. Remove decorative front by tilting lower portion forward to release ball catch and lifting front off mounting bracket. See Figure 75. -
Page 65: Parts View
pARTS vIEW MILLIVOLT BURNER ASSEMBLY RF VALVE BURNER ASSEMBLY INTERMITTENT PILOT BURNER ASSEMBLY BLOWER ASSEMBLY - RF MODELS LOG SET ASSEMBLY DI BURNER ASSEMBLY 26408-0-1009 Page 65... -
Page 66: Parts List
pARTS LIST Index part Number Description Dvp36Dp31(N,p)-1 Dvp36Dp51N-1 Dvp36Dp71(N,p)-1 Dvp36Dp91(N,p)-2 R7654 R7654 R7654 R7654 Insulation, Flue 17426 17426 17426 17426 Retainer, 5” Flue R7566 R7566 R7566 R7566 Vent Adapter R7573 R7573 R7573 R7573 Vent Gasket 17155 17155 17155 17155 Flue Outlet Assy M163 M163 M163... -
Page 67: Parts List
pARTS LIST (continued) Index part Number Description Dvp36Dp31(N,p)-1 Dvp36Dp51N-1 Dvp36Dp71(N,p)-1 Dvp36Dp91(N,p)-2 16223 16223 16223 16223 Spring Retainer Assembly R3435 R8147 R721 Wire Assembly R2708 Piezo Ignitor R3436 Remote/On/Off Switch R1995 Transformer (IP) R7615 R5160 Cord Set R8144 Wire Harness (DI) R5751 Wire Harness (IP) 18880... -
Page 68: Fbb4 Variable Speed Blower Installation
FBB4 VARIABLE SPEED BLoWER InSTALLATIon Attention: Install blower assembly before connecting gas inlet 5. Insert blower assembly into interior, bottom of fireplace. supply line Position blower assembly behind gas valve, align notch on back of blower assembly with center screw on fireplace back Note: junction box on right side of fireplace must be pre-wired at and push blower assembly against fireplace back. - Page 69 FBB4 VARIABLE SPEED BLoWER InSTALLATIon FBB4 BLOWER ASSEMBLY COMpLETE R7649 FAN CONTROL R4192 SPEED ConTRoL KnoB R4186 SpEED CONTROL 110 VOLT AC JUNCTION BOX BLACK SWITCH WHITE GROUND SPEED CONTROL 26408-0-1009 Page 69...
-
Page 70: Junction Box Wiring Installation Instructions
JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS CAUTION: ALL WIRING SHOULD BE DONE BY A qUALIFIED ELECTRICIAN AND SHALL BE IN COMpLIANCE WITH ALL LoCAL, CITY AnD STATE BUILDInG CoDES. BEFoRE MAKInG THE ELECTRICAL ConnECTIon, MAKE SURE THAT MAIn PoWER SUPPLY IS DISConnECTED. THE APPLIAnCE, WHEn InSTALLED, MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL ELECTRICAL CODE ANSI/NFpA 70 (LATEST EDITION). -
Page 71: Accessories
ACCESSORIES The following accessory parts can be obtained from your Empire Comfort Systems dealer. If you need additional information beyond what your dealer can furnish, contact Empire Comfort Systems Inc., Nine Eighteen Freeburg Ave., Belleville, Illinois 62220-2623. Accessory Description Model Number... -
Page 72: Master Parts Distributor List
For the current list, please click on the Master Parts button at www.empirecomfort.com. Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original Equipment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc. Star-Fire Distributors... -
Page 73: Quick Reference Guide
Empire Comfort Systems Web Site www.empirecomfort.com 918 Freeburg Avenue Belleville, Illinois 62220-2623 The Studio Series Direct Vent Zero Clearance GAS-FIRED Gas Fireplace Heater Millivolt Standing pilot: dvp36dp31(n,p)-1 diRECt ignition pilot: dvp36dp51n-1 intERMittEnt pilot: dvp36dp71(n,p)-1 REMotE Rf ModElS: dvp36dp91(n,p)-2 fireplace requires one of the following fronts:... -
Page 74: Firebox Dimensions
Empire Comfort Systems Web Site www.empirecomfort.com 918 Freeburg Avenue Belleville, Illinois 62220-2623 The Studio Series Direct Vent Zero Clearance GAS-FIRED Gas Fireplace Heater Millivolt Standing pilot: dvp36dp31(n,p)-1 diRECt ignition pilot: dvp36dp51n-1 intERMittEnt pilot: dvp36dp71(n,p)-1 REMotE Rf ModElS: dvp36dp91(n,p)-2 fireplace requires one of the following fronts:... -
Page 75: Service Notes
SERvICE NOTES 26408-0-1009 Page 75... - Page 76 Empire Comfort Systems Inc. EMPIRE EMPIRE 918 Freeburg Ave. Belleville, IL 62220 If you have a general question about our products, please e-mail us at info@empirecomfort.com. If you have a service or repair question, please contact your dealer. Comfort Systems www.empirecomfort.com...