Page 1
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.
... 13 uSing tHe deptH Stop ... 13 making a Cut ... 13 maintenanCe and SerViCing ... 15 SKU 98199 For technical questions, please call 1-800-444-3353. Cleaning, maintenanCe, and lubriCation ... 15 replaCing tHe blade ... 15 adjuSting tHe FenCe ...
Page 3
SKU 98199 For technical questions, please call 1-800-444-3353. notiCe is used to address practices not related to personal injury. Caution, without...
Page 4
ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eye- SKU 98199 For technical questions, please call 1-800-444-3353. glasses only have impact resistant lenses, they are NOT safety glasses.
Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or miss- ing, contact Harbor Freight Tools for a replacement. Avoid unintentional starting. Prepare to begin work before turning on the tool.
SaVe tHeSe inStruCtionS. SKU 98199 For technical questions, please call 1-800-444-3353. grounding inStruCtionS to preVent eleCtriC SHoCk and deatH From...
To reduce the risk of vibration-related injury: SKU 98199 For technical questions, please call 1-800-444-3353. Anyone using vibrating tools regu- larly or for an extended period should first be examined by a doctor and...
When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. list of contents...
(not included). This will help prevent tipping or movement of the saw, preventing injury. Also, the use of a saw table will make it easier to efficiently handle work materials and make more accurate cuts. operating inStruCtionS...
Instructions for checking and adjusting these angles are discussed later in this booklet. SKU 98199 For technical questions, please call 1-800-444-3353. It is very important that the work material be properly supported before making a cut. The material must be level on the Table.
To set the bevel angle, loosen the Bevel Lock Handle at the rear of the saw. To do this, press in the Lock Button and rotate the Handle 1/2 turn counterclockwise. Move the blade assembly left to the desired angle.
Page 13
Blade. When the cut is completed, raise the blade assembly, wait for the Blade to stop turning, release the Hold Down Vise and remove the work material from the saw. SKU 98199 For technical questions, please call 1-800-444-3353. Page 13...
Clean, then store the tool indoors out of children’s reach. SKU 98199 For technical questions, please call 1-800-444-3353. If the blade has become dirty, use a blade cleaner (not included) to clean it.
Page 15
Center Cover in place by turning it counterclockwise. (See Figure 2.) Figure 3 Remove the Safety Screw. (See Figure 3.) SKU 98199 For technical questions, please call 1-800-444-3353. Figure 4 Figure 5 Raise the Blade Guard and Center Cover. (See Figure 4.)
Saw Blade. Before beginning work, make a test cut on scrap material with the Table set at 90º. SKU 98199 For technical questions, please call 1-800-444-3353. Check the cut with an accurate square. You can also reverse the two...
Bevel Locking Lever. Once the bevel angle is adjusted, adjust the Bevel Angle Indicator to read 0º when the Saw Blade is in the vertical position. Loosen the screw holding the Indicator in place, adjust it to be exactly over the 0º mark, then retighten the screw.
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 98199 For technical questions, please call 1-800-444-3353. troubleshooting likely Solutions Check power at outlet.
Flat Washer Lock Nut Rail Flat Washer Spring Washer Bolt M6X30 Screw Clamp Screw Bolt Flat Washer Pointer SKU 98199 For technical questions, please call 1-800-444-3353. partS liSt part# description Spring Bend Arm Flat Washer Lock Nut Washer Bolt Lock Handle...
Page 20
If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 98199 For technical questions, please call 1-800-444-3353. partS liSt...
90 daY warrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.