Freight Tools at the number shown on the cover of this manual as soon as possible. Note: Before first use, the Battery (64) will require charging. The first charge requires 8 hours charge time. See charging instructions on page 10. SKU 93827 For technical questions, please call 1-800-444-3353. Contents...
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. SKU 93827 For technical questions, please call 1-800-444-3353. " "...
Page 4
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. SKU 93827 For technical questions, please call 1-800-444-3353. Electrical Safety...
Page 5
Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. SKU 93827 For technical questions, please call 1-800-444-3353. Tool Use and Care Page 5...
Page 6
The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See Figure A.) SKU 93827 For technical questions, please call 1-800-444-3353. Service...
Page 7
The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure C.) SKU 93827 For technical questions, please call 1-800-444-3353. FIGURE A...
Page 8
Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. SKU 93827 For technical questions, please call 1-800-444-3353. Symbology Page 8...
Maintain labels and nameplates on this item. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. When using a handheld power tool, always maintain a firm grip on the tool with both hands.
Then, disconnect the Charger from the Battery. * The Battery (64) require an initial charge time of 8 hours. Do not recharge the Battery more than 5 hours after this initial charging. SKU 93827 For technical questions, please call 1-800-444-3353. (62)
Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagrams at the end of the manual. WARNING: Always make sure the Battery (64) of the Circular Saw is removed prior to making any adjustments to the tool, except for adjusting the depth of cut (required to install the battery).
Page 12
To Adjust the Angle of Cut: A. Loosen the Angle Knob (34). B. Pivot the Saw body in relation to the Foot (35) to adjust the angle. Read the angle from the arrow and scale near the Angle Knob. C. Retighten the Angle Knob (34) securely.
Page 13
When the Saw Blade is pinched or bound tightly by the kerf (i.e. the slot that was cut) closing down, the Saw Blade stalls and the Motor reaction drives the tool rapidly toward the operator. If the Saw...
AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 93827 For technical questions, please call 1-800-444-3353. Page 14...
Part 64 - Battery - not shown. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as original or replacement parts. SKU 93827 For technical questions, please call 1-800-444-3353. i r r Page 15...