Table of Contents
Advertisement
Quick Links
14" HEAVY DUTY CUT-OFF SAW
ASSEMBLY AND OPERATING INSTRUCTIONS
Visit our Web site at http://www.harborfreight.com
READ AND UNDERSTAND ALL WARNINGS
Copyright
of this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Model 47003
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
AND INSTRUCTIONS BEFORE USE.
©
2004 by Harbor Freight Tools
®
. All rights reserved. No portion
Advertisement
Table of Contents
Related Manuals for Chicago Electric 47003
Summary of Contents for Chicago Electric 47003
- Page 1 2004 by Harbor Freight Tools of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353 Model 47003 ®...
-
Page 2: Product Specifications
When unpacking, check to make sure all the parts shown on the Parts List on page 17 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. -
Page 3: Work Area
Holding the work by hand is unstable and may lead to loss of control. Only work on a workpiece that is properly secured by tightening the Clamp- ing Screw (4). SKU 47003 WORK AREA PERSONAL SAFETY TOOL USE AND CARE... -
Page 4: Electrical Safety
Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or SKU 47003 SERVICE ELECTRICAL SAFETY... - Page 5 Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low SKU 47003 eliminates the need for the GROUNDING...
-
Page 6: Extension Cords
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure B.) When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Figure B.) SKU 47003 EXTENSION CORDS PAGE 6... - Page 7 7.1 – 12.0 12.1 – 16.0 16.1 – 20.0 * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. FIGURE B FIGURE C SKU 47003 (120 VOLT) EXTENSION CORD LENGTH Feet Feet SYMBOLOGY Double Insulated...
-
Page 8: Specific Safety Rules
Maintain labels and nameplates on the Cut-Off Saw. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replace- ment. Keep hands and fingers away from cutting area and Cut-Off Wheel. Keep one hand on the Handle and your second hand on the motor housing. If both hands are holding the saw, your hands and fingers cannot be cut by the Cut-Off Wheel. - Page 9 Cut-Off Wheel. Before using the Cut-Off Saw, make sure the Cut-Off Wheel is properly mounted on the Saw Spindle. Make sure the Cut-Off Wheel is balanced, and is not cracked or bent. The Cut-Off Wheel will become hot while cutting. Allow the Cut-Off Wheel to completely cool before touching.
- Page 10 Also, make sure the Cut-Off Wheel has completely cooled and wear work gloves while replacing the Wheel. Place the Cut-Off Saw in its fully raised position. To do so, turn the Swing Lock Handle (81) clockwise while pushing down on the Handle (66, 71).
- Page 11 (61) To keep the Cut-Off Wheel (57) from turning: Depress the Lock Pin (40) and turn the Cut-Off Wheel until the Lock Pin clicks into place. (See Figure E, and Figure F, next page.) SKU 47003 (61) FIGURE D (57)
- Page 12 RPM. Cut-Off Wheels that do not match the mounting hardware of the Saw or that are rated at less than the saw’s maximum RPM may fly off the Saw or may run eccentrically, causing loss of control. 8 mm HEX WRENCH...
- Page 13 Hex Nut. (See Figure I.) To Operate The Cut-Off Saw: To operate the Cut-Off Saw, first make sure the Saw Arm (46) is in its the upright position with the Swing Lock Handle (81) disengaged. (See Figure D.) SKU 47003...
- Page 14 If the Cut-Off Wheel (57) does not pass completely through the workpiece, Raise the Saw Arm, turn off and unplug the Saw, and wait until it comes to a complete stop. Remove stock being cut. Then, lower the Cut-Off Wheel, following the instructions on page 13 .
-
Page 15: Inspection, Maintenance, And Cleaning
Unplug the Cut-Off Saw from its electrical outlet, and make sure to wait until the Saw has come to a complete stop before removing the workpiece. Lock down the Saw with the Swing Lock Handle (81) and store the Saw in a dry, safe location. -
Page 16: Please Read The Following Carefully
TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 47003 PAGE 16... -
Page 17: Parts List
Guide Bearing Armature Lock Pin Pin Spring C-Clip NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 47003 PARTS LIST Qty. Part # Description Bearing Screw Rubber Cylinder Saw Arm... -
Page 18: Assembly Diagram
ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 47003 PAGE 18...