Advertisement
10" TILE SAW,
2.5 HP WITH PVC TRAY
46225
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
©
®
Copyright
2001 by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Advertisement
Table of Contents
Related Manuals for Chicago Electric 46225
Summary of Contents for Chicago Electric 46225
- Page 1 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353.
-
Page 2: Specifications
Do not force tool. It will do the job better and more safely at the rate for which it was intended. Do not use inappropriate attachments in an attempt to exceed the tool capacity. SKU 46225 For technical questions, please call 1-800-444-3353. Specifications DESCRIPTION 39-3/4”L x 21”W x 48-3/4”H... - Page 3 17. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. SKU 46225 For technical questions, please call 1-800-444-3353.
- Page 4 Common household current is 110-120V. As long as the outlet used with the Tile Saw is rated from 110-120V there will be no complications using it with house- hold receptacles. Plug the tool into a 110-120V properly grounded outlet pro- tected by a 15-Amp, dual element time delay or circuit breaker.
-
Page 5: Extension Cords
(signified by “WA” on the jacket). When unpacking, check to make all parts listed on Pages 10-11 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. -
Page 6: Changing/Installing The Blade
Assembly and Operating Instructions for the Table Stand. If the Stand is not to be used with the Tile Saw, the Saw must be securely mounted onto a flat, level surface capable of supporting the weight of the Tile Saw in addition to the weight of all work pieces. -
Page 7: Operation
(Fence) on the back of the Table. Align the cut mark with the Blade. Once the Tile Saw has been turned on, allow the Blade to spin up to full speed. Watch to be sure that the Pump is supplying a continuous flow of water to the Blade. -
Page 8: Maintenance
Always unplug the Power Cord before servicing and before performing any maintenance. General Maintenance: Regularly inspect the Diamond Saw Blade. Using a dull Blade will cause excessive wear on the Motor, and will not produce a satisfactory cut. Replace with a new one when needed. - Page 9 10. Do not let the Pump run when it is not submerged in water. Running the Pump out of the water will damage the Pump. 11. If the Pump still does not work, it must be replaced. Replacement Pumps are available through Harbor Freight Tools. Figure A PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIA- GRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
-
Page 10: Parts List
Supporting frame Shaft Tension adjust plate Flat washer Bolt Motor wheel Screw Motor Blade guard Fig. 1 SKU 46225 For technical questions, please call 1-800-444-3353. Parts List Description Item Brass tube Water baffle Screw Water Connector Locking knob Flat washer... - Page 11 Table Wheel Flat washer Bolt Parallel guide Angle guide Pump Circuit Breaker Cap Pump Parallel Guide SKU 46225 For technical questions, please call 1-800-444-3353. Parts List, Cont. Power Switch Brake Shaft Button Angle Guide Fig. 2 REV 03/05 Page 11...
-
Page 12: Assembly Drawing
Assembly Drawing NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. REV 03/05 SKU 46225 For technical questions, please call 1-800-444-3353. Page 12...