Sign in today to find solutions:

Forgot your password?

Don't have an account? Sign up

Harbor Freight Tools 42933 Instructions Manual

Harbor freight tools chicago electric series radial arm saw model 42933 assembly and operating instructions.

 
RADIAL ARM SAW
ASSEMBLY AND OPERATING
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
©
Copyright
2000 by Harbor Freight Tools
manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
1
8-
/
INCH
4
42933
INSTRUCTIONS
®
. All rights reserved. No portion of this
REV 11/04; 12/06

Summary of Contents

  • Page 1

    Copyright 2000 by Harbor Freight Tools manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353. INCH 42933 ®...

  • Page 2

    Do not force tool. It will do the job better and more safely at the rate for which it was intended. Do not use inappropriate attachments in an attempt to exceed the tool capacity. SKU 42933 For replacement parts, please call 1-800-444-3353. Specifications...

  • Page 3

    18. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. SKU 42933 For replacement parts, please call 1-800-444-3353. Page 3...

  • Page 4

    Always use the anti-kickback finger attachment when making rip cuts. Feed stock from the opposite end from the anti-kickback finger attachment. Always use the saw blade guides and fence, and never push stock being cut by hand. Tighten and lock all adjusting (saw blade positioning) screws before operating.

  • Page 5

    Handle. 22. Avoid Kickback of stock: - For rip cuts, the saw blade must be exactly parallel to the fence to prevent pinching or heeling. Use a stock separator on the output side of the stock cut.

  • Page 6

    Assembly Drawing at the end of this manual. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. During the assembly and installation procedure, you may have to refer to the Parts List and Assembly Drawings located at the end of this manual.

  • Page 7

    Screw Clamp (137) ON / OFF Switch – The Switch has a built-in locking feature which requires a key to be inserted before the saw can be turned ON. Removing the Key and pushing the OFF button locks the saw against unintended use.

  • Page 8

    Depth of Cut – The Elevating Handle (100) at the rear of the arm is used to raise and lower the height of the Saw Blade. Turn the Elevating Handle clockwise to raise the Saw Blade or counter- clockwise to lower it.

  • Page 9

    - Check that the Saw blade follows this line from front to back. If the Saw Blade moves to the right or left side of the line as it travels the entire length of the Arm, loosen the Screw Clamps (137) and lightly tap on the Table left or right side until there is full travel alignment.

  • Page 10

    With the same hand that you turned ON the machine, loosen the Carriage Lock Knob and slowly move the Saw Blade back, cutting the rip fence; and then move it all the way forward, cutting a groove into the entire depth of the plywood.

  • Page 11

    Adjust the Elevating Handle (100) so the Saw Blade (17) height is only 1/8 inch into the worktable. Push the Handle backward so that the Saw Blade is in behind the stock to be cut. Press the green Switch (122). Squeeze the Handle Trigger and slowly pull the Handle toward you, causing the Saw Blade to cut the stock.

  • Page 12

    Ripping is the process of cutting stock along the grain (or lengthwise). The stock if fed into the Saw Blade against the blade rotation (similar to a table saw). The fence is used as a guide to help maintain cutting width.

  • Page 13

    Out-ripping is done when the in-rip position will not permit a wide enough cut. This function moves the Saw Blade to the front of the machine. This operation is the same as in-rip cut- ting (previously described), with the exception that the Pivot Yoke is turned so that the Handle is on the right side of the machine (opposite of the in-rip position).

  • Page 14

    Saw Blades – Never use a replacement blade rated lower than 5,000 RPM, and larger than 8 inches diameter. Motor Brushes – Inspect the two motor Brushes (55) after the first 50 hours of saw use. After that, check every 10 hours. Replace if necessary by a qualified technician.

  • Page 15

    , s t , s l SKU 42933 For replacement parts, please call 1-800-444-3353. Troubleshooting l e l l e l l e l n i l...

  • Page 16

    × × × × l i o p i l × × × l l o SKU 42933 For replacement parts, please call 1-800-444-3353. Parts List t l i × × × l l o × l a i ×...

  • Page 17

    Assembly Diagram (1-97) NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 42933 For replacement parts, please call 1-800-444-3353. Page 17...

  • Page 18

    Assembly Diagram SKU 42933 For replacement parts, please call 1-800-444-3353. Page 18...

  • Page 19

    TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 42933 For replacement parts, please call 1-800-444-3353. Page 19...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: