Sign in today to find solutions:

Don't have an account? Sign up

Harbor Freight Tools 92158 Assembly And Operation Instructions Manual

Harbor freighttools bandfile 1/2 inch belt sander operation instructions 92158.

 
BANDFILE
Assembly And OperAtiOn instructiOns
Due to continuing improvements, actual product may differ slightly from the product described herein.
Visit our website at: http://www.harborfreight.com
tO preVent seriOus injury, reAd And understAnd
All wArnings And instructiOns befOre use.
©
Copyright
2004 by Harbor Freight Tools
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
for technical questions or replacement parts, please call 1-800-444-3353.
BELT SANDER
3491 Mission Oaks Blvd., Camarillo, CA 93011
1
/
INCH
2
92158
®
. All rights reserved. No portion of this manual
®
Next page ->

Summary of Contents

  • Page 1

    © Copyright 2004 by Harbor Freight Tools or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. for technical questions or replacement parts, please call 1-800-444-3353. INCH 92158 ®...

  • Page 2

    Water entering a power tool will increase the risk of electric shock. for technical questions, please call 1-800-444-3353. SKU 92158 specificAtiOns 120 V~, 60 Hz, 600 watts, n 2300 FPM (feet per minute) (single speed);...

  • Page 3

    15. use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. for technical questions, please call 1-800-444-3353. SKU 92158 eliminates the need for the three wire grounded power personal safety...

  • Page 4

    “live” and shock the operator. maintain labels and nameplates on the belt sander. These carry important informa- tion. If unreadable or missing, contact Harbor Freight Tools for a replacement. for technical questions, please call 1-800-444-3353.

  • Page 5

    Avoid unintentional starting. Make sure you are prepared to begin work before turn- ing on the Belt Sander. do not force the belt sander. This tool will do the work better and safer at the speed and capacity for which it was designed.

  • Page 6

    OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (see figure b.) for technical questions, please call 1-800-444-3353. SKU 92158 grOunding wArning! figure b...

  • Page 7

    16.1 – 20.0 figure c * based on limiting the line voltage drop to five volts at 150% of the rated amperes. for technical questions, please call 1-800-444-3353. SKU 92158 extensiOn cOrds (120 Or 240 VOlt) extensiOn cOrd length 50 feet...

  • Page 8

    Drawing and Parts List at the end of this manual. Not shown are five accessory Sanding Belts. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible.

  • Page 9

    Loosen Screw (49) and adjust Bracket (22) to the desired angle for sanding. Plug the Line Cord (52) into a GFCI electrical outlet. Always follow all safety instructions and warnings in this instruction manual. for technical questions, please call 1-800-444-3353. SKU 92158 Screw (26) Cover (23) controls...

  • Page 10

    Begin sanding with light movements and pressure until the sanding capability is known on the material being sanded. When finished using the Belt Sander, press the On / Off Switch (48) to the Off (O) position. Wait until the motor stops before setting the tool down.

  • Page 11: Table Of Contents

    Assumes All risK And liAbility Arising Out Of his Or her repAirs tO the OriginAl prOduct Or replAcement pArts theretO, Or Arising Out Of his Or her instAllAtiOn Of replAcement pArts theretO. for technical questions, please call 1-800-444-3353. SKU 92158 pArts list part Washer, Spring...

  • Page 12

    Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. for technical questions, please call 1-800-444-3353. SKU 92158 Page 12...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: