Assembly diagram and Parts List for Large spray gun... 14 Assembly diagram and Parts List for small spray gun ... 15 Troubleshooting ... 16-17 For technical questions, please call 1-800-444-3353; SKU 94572 Troubleshooting section at end of manual. Contents Page 2...
Do not modify this tool and do not use this tool for a purpose for which it was not intended. For technical questions, please call 1-800-444-3353; SKU 94572 Troubleshooting section at end of manual. Specifications Large HVLP Spray Gun 30 to 35 PSI, 35 PSI Max.
Page 4
Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs.
Page 5
WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code 25249.5, et seq.) For technical questions, please call 1-800-444-3353; SKU 94572 Troubleshooting section at end of manual. Page 5...
When unpacking, check to make sure the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at: 1-00-444-3353 as soon as possible. Spanner 1.8 mm Additional Nozzle Case 20 oz. Cup 4.2 oz. Cup For technical questions, please call 1-800-444-3353;...
For best service you should incorporate a regulator and inline filter, as shown in the diagram above. Hoses, couplers, regulators, and filters are all available at Harbor Freight Tools. Note: Compressor pumps discharge condensed water, oil, or other contaminants along with the compressed air.
FIGURE 1 Turn the Air Cap (1A) to produce vertical and horizontal spray patterns. For technical questions, please call 1-800-444-3353; SKU 94572 Troubleshooting section at end of manual. Control Layout Turn the Pattern Control Knob (7A) clockwise to adjust the paint / air mixture.
If it appears to thin, add a very small amount of thinner (not included). BE CAREFUL when thinning. Proceed slowly, adding very minimal amounts. NEVER exceed the manufacturer’s thinning recommendations. For technical questions, please call 1-800-444-3353; SKU 94572 Troubleshooting section at end of manual. Conventional HVLP...
URE 1 on page 6). By turning it counterclockwise (all the way open), the pattern will flatten. Turn the Pattern Control Knob (7A) clockwise for a round pattern. See FIGURE 4 below. Flat/Open For technical questions, please call 1-800-444-3353; SKU 94572 Troubleshooting section at end of manual. Horizontal Fan Air Cap Vertical Fan...
While holding the Viscosimeter over the material source can, let go of the output hole and count the number of seconds it takes for it to empty completely. The number of seconds is the viscosity rating. For technical questions, please call 1-800-444-3353; SKU 94572 Troubleshooting section at end of manual. Too Fine Correct...
Clean out the gun thoroughly after EVERY use, according to the instructions found on the next page. For technical questions, please call 1-800-444-3353; SKU 94572 Troubleshooting section at end of manual. Techniques FIGURE 6...
After cleaning your Spray Gun, properly dispose of your cleaning solutions according to the solution manufacturer’s direction and local hazardous waste standards. For technical questions, please call 1-800-444-3353; SKU 94572 Troubleshooting section at end of manual. Maintenance SOLVENT SELECTION...
Assembly Diagram And Parts List For 1.4mm Spray Gun 22A 24A Pattern Control Knob Fluid Control Knob For technical questions, please call 1-800-444-3353; SKU 94572 Troubleshooting section at end of manual. 8A 9A 10A 16A 17A 18A 19A Air Control Knob...
Assembly Diagram And Parts List For 1.0mm Spray Gun Air Control Knob Pattern Control Knob Fluid Control Knob For technical questions, please call 1-800-444-3353; SKU 94572 Page 15 Troubleshooting section at end of manual.
2. Holes on one side of the Air cap are plugged. (Clean the Air cap with a nonmetallic point.) If the steps above do not solve the problem or if the repairs involved are too SKU 94572 For technical questions, please call 1-800-444-3353.
Page 17
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as re- placement parts. If the steps above do not solve the problem or if the repairs involved are too SKU 94572 For technical questions, please call 1-800-444-3353. Troubleshooting (continued) complex, contact a qualified technician.
Page 18
Improper cleaning is a common reason for the Spray Gun not to work. 90 day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability stan- dards, and warrants to the original purchaser that this product is free from defects in materials and workman- ship for the period of 90 days from the date of purchase.