Harbor freight tools central pneumatic series 2 in 1 flooring cleat staple nailer model 94446 assembly and operating instructions contractor series (12 pages)
Page 1
2008 by Harbor Freight Tools herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.
Use safety equipment. A dust mask, non-skid safety shoes and a hard hat must SKU 98917 For technical questions, please call 1-800-444-3353. be used for the applicable conditions. Wear heavy-duty work gloves during use. Wear a full face shield if you are producing metal filings or wood chips.
Many accidents are caused by poorly maintained tools. There is a risk of bursting if the tool is damaged. SKU 98917 For technical questions, please call 1-800-444-3353. Use only accessories that are identified by the manufacturer for the specific tool model.
WARNING marking concerning Risk of Respiratory Injury. Wear NIOSH- approved dust mask/respirator. WARNING marking concerning Risk of Explosion. SKU 98917 For technical questions, please call 1-800-444-3353. Specific Safety Instructions The warnings and precautions dis- cussed in this manual cannot cover all possible conditions and situations that may occur.
Page 6
SKU 98917 For technical questions, please call 1-800-444-3353. use. Pregnant women or people who have impaired blood circulation...
When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown throughout the manual as soon as possible. • This air tool may be shipped with a protective plug covering the air inlet.
Page 8
If the tool will not be used at this time, turn off and detach the air supply and safely discharge any residual air pressure. SKU 98917 For technical questions, please call 1-800-444-3353. Note: Residual air pressure should not be present after the tool is disconnected from the air supply.
ALWAYS point the Nailer at a piece of scrap wood when testing. Make sure the tool is disconnected from its air supply. SKU 98917 For technical questions, please call 1-800-444-3353. Completely empty the Magazine (71) of Nails. The Nailer should not fire if the Nose Safety Guide (42) is not depressed against the workpiece.
Nails. INSERT NAILS Trigger (56) Feeder Shoe (69) Nose Safety Guide (42) SKU 98917 For technical questions, please call 1-800-444-3353. Attach the Nailer to the air supply at the Air Plug (83). Start your compressor and check the pressure, making sure you do not exceed the maximum 120 PSI.
Magazine to clear a jammed nail, have a qualified service technician perform this procedure. SKU 98917 For technical questions, please call 1-800-444-3353. Remove the Screw (35) from each side of the Magazine. (One on each Magazine side.) Remove the two...
Try to fire the Nailer into a piece of scrap wood or flooring to ensure that it is disconnected and inca- pable of firing any nails/staples. SKU 98917 For technical questions, please call 1-800-444-3353. Inspect the air supply screen located in the End Cap (82) before each use.
Other problems. 1. Have a qualified service technician check out the tool. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. SKU 98917 For technical questions, please call 1-800-444-3353. Troubleshooting Possible Solution attempting to fire a nail.
RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 98917 For technical questions, please call 1-800-444-3353. PARTS LIST...
ASSEMBLY DIAGRAM NOTE: Some parts are listed and show for illustration purposes only, and are not available individually as replacement parts. REV 09g SKU 98917 For technical questions, please call 1-800-444-3353. Page 15...
Page 16
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.