1. Manuals
  2. Brands
  3. Central Machinery Manuals
  4. Lathe
  5. 90692
  6. Assembly and operating instructions manual

Central Machinery 90692 Assembly And Operating Instructions Manual

Lathe duplicator attachment (for use with lathe model 90265)
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
LATHE DUPLICATOR ATTACHMENT
(FOR USE WITH LATHE MODEL 90265)
MODEL 90692
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http//www.harborfreight.com
Copyright
2003 by Harbor Freight Tools. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.

Advertisement

Table of Contents
loading

Related Manuals for Central Machinery 90692

Summary of Contents for Central Machinery 90692

  • Page 1 Visit our Web site at http//www.harborfreight.com Copyright 2003 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.

  • Page 2: Handle

    When unpacking, check to make sure all the parts shown in the Parts List on page 13 are included. If any parts are missing or broken, please call Harbor Freight Tools at the num- ber shown on the cover of this manual as soon as possible.
  • Page 3 If there is any doubt, do not attempt to use this product. Maintain labels and nameplates on this product. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replace- ment. Dress safely. Do not wear loose clothing or jewelry, as they can become caught in moving parts.

  • Page 4: Safety Shield

    SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS This Lathe Duplicator Attachment is designed for use ONLY with the Lathe Model 90265 (available from Harbor Freight Tools). Make sure to read and understand all instructions and safety precautions as outlined in the manu- facturer’s manual for the Model 90265 Lathe with which the Lathe Duplicator...

  • Page 5: Assembly Instructions

    Assembly Diagram on page 14. To Attach The Tool Rest Base: Loosen the Tool Rest Handle of the lathe , and slide the Tool Rest Base of the lathe to as near the Headstock of the lathe as possible. (See Figure A.) Loosen the Support Bar Handle of the Model 90265 lathe , and remove the Tool Rest Base of the lathe .

  • Page 6: Bracket

    Install one Lower Vertical Support Bar (46) onto the Tool Rest Base of the lathe , and secure it by tightening the Support Bar Handle of the lathe. (See Figure A.) Loosen the Tailstock Handle of the lathe , and remove the Tailstock from the Bed of the lathe .
  • Page 7 Handles into the two Square Nuts (47) on the Support Bar (54). (See Figure D.) Replace the End Cap (12) on each end of the Support Bar (54). (See Assy. Diagram.) SKU 90692 U-BRACKET (38) HANDLE (3) LOWER VERTICAL SUPPORT BAR...
  • Page 8 Cutting Tool in place. (See Figure E.) Slide the Pattern Follower Assembly into the T-Slot located at the bottom of the Tool Holder (24). (See Figure E.) TOOL HOLDER (24) T-SLOT SKU 90692 SQUARE NUT (47) LOCKWASHER (34) FLAT WASHER (40)

  • Page 9: Pointer

    Handle onto the Bolt. (See Figure G.) Attach the Safety Shield Bracket (10) to the Safety Shield Plate (43), using a Hex Head Bolt (11), Flat Washer (40), and Hex Nut (39). (See Figure G.) SKU 90692 POINTER (14) TOOL HOLDER SLIDE PLATE...

  • Page 10: Cutting Tool

    To Adjust The Cutting Tool: Prior to use, the Cutting Tool (31) must be set approximately 1/8” above the Spindle of the lathe . Make sure to check at the Headstock and Tailstock of the lathe. (See Figure H.) The Cutting Tool (31) can be adjusted vertically by loosening the Support Bar Handles (45) which secure the Lower Vertical Support Bars (46) in place.

  • Page 11: Pattern Bolt

    To Perform Duplicate Turning: Mount the original woodstock that is to be duplicated in the Pattern Bolts (42). The Tool Rest Bases (44) will need to be adjusted along the Bed of the lathe to the required length. (See Figures A, and C.) Mount the new piece of woodstock in the lathe.
  • Page 12 For better and safer performance, always keep the Cutting Tool (31) clean and sharp. Daily, with a clean cloth, brush, or vacuum remove all debris fromthe Lathe Dupli- cator Attachment. Then, use a lightweight machine oil to lubricate all moving parts.

  • Page 13: Table Of Contents

    Flat Washer (#10) Lock Washer (#10) Wing Nut (#10-24) Tool Holder Socket Head Bolt (#10-24*3/8”) Bracket Ball Bearing (R83022) ----------- --------------------------------------------- -------- 55 SKU 90692 PARTS LIST Qty. Part # Description Flat Washer (1/4”) Hex Nut (1/4”-20) Cutting Tool Dowel Pin Base Dowel Pin (3*18.7MM)

  • Page 14: Assembly Diagram

    38 1 23 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 90692 ASSEMBLY DIAGRAM 52 50 18 34 PAGE 14 40 1...

Table of Contents