Table of Contents
Advertisement
Инструкции по эксплуатации
Video Cassette Recorder
Contents
Before attempting to connect, operate or adjust this product,
please read these instructions completely.
Operating Instructions
Model No
NV-MV41 Series
RQTV0014
.
Page
2
3
4
5
5
7
7
7
8
9
10
13
15
17
19
Advertisement
Table of Contents
Related Manuals for Panasonic NV-MV41 Series
Summary of Contents for Panasonic NV-MV41 Series
-
Page 1: Table Of Contents
Operating Instructions Инструкции по эксплуатации Video Cassette Recorder Model No NV-MV41 Series Contents Page Warning and Important Information Controls and Components Connections Tuning the TV to Your VCR Storing TV Broadcasts in Your VCR Language Setting of the On Screen Display... -
Page 2: Warning And Important Information
Plus, [Alumina] Head Cleaner further enhanced cleaning such as a book case or similar unit. efficiency. • Based on in-house tests with Panasonic video cassettes. WARNING: Actual head life may vary according to conditions of use, To reduce the risk of fire, electric shock or product tape type, temperature, humidity, etc. -
Page 3: Controls And Components
ENGLISH Controls and Components (16) (34) (35) (17) (18) (19) EJECT TIMER REC REC/OTR TRACKING/V-LOCK (20) -/- - (36) (37) (14) (38) (20) (39) (40) (41) (22) (10) (12) (27) (21) CANCEL INPUT SEL AUDIO PROG PLAY (22) (23) TIMER (24) PROG CHECK... -
Page 4: Connections
(6) AC Input socket (42) (1) Aerial (Not supplied) ¢ To mains supply • If you are using a Panasonic TV, this setting has already (2) TV Set (Not supplied) (3) Aerial Connector been made, and so you do not need to perform the above (4) RF IN socket (45) setting procedure. -
Page 5: Tuning The Tv To Your Vcr
TV displays this pattern. • Auto Tuning commences. If Auto Tuning stops halfway by turning the VCR off or a Panasonic VCR power failure, Or if the VCR is turned on without the aerial connected RF SELECT... - Page 6 Auto Tuning Using the On Screen Display Manual Tuning Procedure If the VCR is not correctly tuned by Auto Tuning, follow the Introduction procedure below. The VCR is tuned automatically by Plug in Auto Tuning. 1 Press [MENU] (9) to display the Main menu on the TV However, Auto Tuning using the On Screen Display should be performed according to the following method if necessary.
-
Page 7: Language Setting Of The On Screen Display
1 Press [MENU] (9) to display the Main menu on the TV Language Setting of the screen. On Screen Display 2 Press [43] (28) to select [CLOCK SET] then press [ENTER] (26). Select one of the 2 languages displayed: English and 3 When the current clock displays on the VCR is Russian. -
Page 8: Option Setting
3 Present time/Tape counter/Remaining tape time/Index Option Setting Search/OTR indication/JET Rewind Information Display Present time 17:24 MENU OPTION TAPE SELECT AUTO LANGUAGE NTSC INPUT SELECT AUTO CLOCK SET NTSC PB SELECT onPALTV TUNER PRESET Tape counter 0:02.54 JET NAVIGATOR SYSTEM DELETE NAVIDATA OPTION OSD REC... -
Page 9: Playback
OSD REC: To set the conditions for the OSD Playback Recording function. • Press [2 1] (28) to select [ON] or [OFF]. Preparations • Confirm that the VCR is on. OFF: Initially set at this position. • Confirm that the TV is on and the VCR viewing channel is This setting enables OSD Recording. -
Page 10: Recording
To Play Back a Recorded Part Repeatedly Recording Press [REPEAT] (30). The [R] indication appears on the VCR display. Preparations • A recorded part on the tape must be at least 15 minutes long. • Confirm that the VCR is on. •... - Page 11 To Display the Approximate Remaining To Record the Present Date and Time Tape Time (OSD Recording) on the same screen as the picture The remaining tape time can be displayed in the VCR display. 1 Select [TAPE SELECT] from the On Screen Display and This function allows you to record the present date and time select the corresponding video cassette tape length.
-
Page 12: Recording From An External Source
Recording from an external source To Delete all of a Cassette’s This function can be used to make up an edited tape from Contents (Tape Refresh Function) other recordings or video sources. You can delete a cassette contents (the picture, the sound A new scene can be added to the end of previous one. -
Page 13: Timer Recording
9 Press [TIMER (REC)] (14) to switch the VCR over to Timer Recording the timer recording standby mode. • When [JET NAVIGATOR] is set to [ON] (see page 8), the [PROGRAMME IS COMPLETE. REMAINING Easy Timer Programming PROGRAMME 49.] message appears. Up to 16 timer programmes, including weekly and daily •... -
Page 14: To Check And Cancel A Timer Programme
Setting other Programmes in Succession Timer recording for the same programme Repeat steps 1-9 of Easy Timer Programming (page 13). on the next week (Intelligent Timer) When you wish to set the timer recording for programmes Programming a Timer Recording of a TV which will be recorded within 1 week and you have ever Programme Until its End recorded the programmes before, you can record them soon... -
Page 15: Search Functions
To Delete the Jet Navigator Data of a Search Functions Single Video Cassette Tape Keep [CANCEL] (5) pressed for more than 5 seconds while Jet Navigator the Jet Navigator list appears. This VCR can display a list of the recorded programmes on [ss] appears on the list. -
Page 16: Time Stamp Function
To Demonstrate the Jet Navigator Function Notes: • Searching in either direction is possible up to the 20th index Keep [NAVI] (25) pressed for more NO.01 JET NAVIGATOR signal. DATE CH ON CATEGORY than 5 seconds without inserting a 1 / 1 0 8 :0 0 M U S I C •... -
Page 17: Before Requesting Service
• The playback picture is distorted when record the tape in the Before Requesting Service EP mode using MESECAM system. #However, this is not a malfunction. #We recommend PAL system for recording in the EP mode. Message of On Screen Display The error message is indicated in brackets [ Recording will not operate correctly The symptom description is indicated in brackets [... -
Page 18: Adjusting The Playback Picture
Crystal View Control The crystal view control function ensures that you always obtain the optimum picture quality so that you get the best picture automatically. Adjusting the Playback Picture Under normal conditions, the VCR automatically adjusts the playback picture for optimum quality. However, in some cases it may be necessary to adjust it manually. -
Page 19: Specifications
Specifications NV-MV41EE/GCU Power Source: 110–240 V AC 50/60 Hz Power Consumption: 11 W Video Recording System: 2 rotary heads, helical scanning system Video Heads: 4 heads Tape Speed: SP; 23.39 mm/s LP; 11.7 mm/s NTSC SP; 33.3 mm/s EP; 11.1 mm/s Tape Format: VHS tape Record/Playback Time:... - Page 20 MEMO...