Chicago Electric Chicago 44849 Assembly Information
  1. Manuals
  2. Brands
  3. Chicago Electric Manuals
  4. Drill
  5. Chicago 44849
  6. Assembly information
Chicago Electric Chicago 44849 Assembly Information

Chicago Electric Chicago 44849 Assembly Information

Cordless drill kit-18v
Hide thumbs
Table of Contents

Advertisement

Quick Links

CORDLESS DRILL KIT-18V
CORDLESS DRILL KIT-18V
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANuAL.
Visit our Web site at http://www.harborfreight.com
Copyright © 2000 by Harbor Freight Tools. All rights reserved. No portion of this manual
Copyright
2000 by Harbor Freight Tools
©
or any artwork contained herein may be reproduced in any shape or form without the
any artwork contained herein may be reproduced in any shape or form without the express
express written consent of Harbor Freight Tools.
written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353
For technical questions or replacement parts, please call 1-800-444-3353.
Model
ASSEMBLY INFORMATION
ASSEMBLY INFORMATION
Diagrams within this manual may not be drawn proportionally.
3491 Mission Oaks Blvd., Camarillo, CA 93011
3491 Mission Oaks Blvd., Camarillo, CA 93011
REV 01/03
44849
. All rights reserved. No portion of this manual or
®
Revised 03a, 07i
.
®

Advertisement

Table of Contents
loading

Related Manuals for Chicago Electric Chicago 44849

Summary of Contents for Chicago Electric Chicago 44849

  • Page 1 Failure to do so can result in serious injury. 3491 Mission Oaks Blvd., Camarillo, CA 93011 SAVE THIS MANuAL. Visit our Web site at http://www.harborfreight.com Copyright © 2000 by Harbor Freight Tools. All rights reserved. No portion of this manual Copyright 2000 by Harbor Freight Tools ©...

  • Page 2: Specifications

    0-900 RPM, Reversible 3/8” Keyless 4.3 lb. 9” 6 Pc. Screw. Set; 6 Pc. Drill Set; Magnetic Extension Bit SAVE THIS MANuAL Cluttered, damp or wet work areas invite inju- Do not allow children to handle this When not in use, tools and equipment should be stored in a...

  • Page 3: Specific Product Warnings And Precautions

    SECuRE THE MATERIAL. when drilling. NEVER uSE YOuR BODY TO BRACE THE DRILL. body parts, between the part of the Drill being braced and the object it is being braced against. ALWAYS DISCONNECT TOOL FROM ITS ELECTRICAL SuPPLY SOuRCE BEFORE...
  • Page 4 Some states require this recycling. Contact your local solid waste authority for recycling information. Before disposing of Battery cover exposed terminals with heavy duty electrical tape to prevent shorting. KEEP THE CORDLESS DRILL IN ITS CASE WHEN NOT IN uSE. life of the tool. SKU 44849 For technical questions, please call 1-800-444-3353.
  • Page 5 When unpacking, check to make sure all parts shown on the Parts List (page 10) are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
  • Page 6 When the Battery (11) is fully charged, remove the Battery from the Battery Charger. Insert the Battery into the Battery Receptacle located at the bottom of the Drill. Make sure the two Securing Clasps (one on each side of the Battery) engage the Drill.
  • Page 7 Set the Reversing Switch (16) to the “LOCKED” (Center) position. (See Figure D.) Hold the Chuck firmly while turning the forward section of the Chuck This opens the Chuck to accept the drill bit. Insert the drill bit into the chuck fully. Turn the forward section of the Chuck to tighten the Chuck around the drill bit shaft.

  • Page 8: Operating Instructions

    The three-position Reversing Switch is located on top of the Trigger. When the Reversing Switch is in the When the Reversing Switch is pressed to the clockwise (typically for removing fasteners or freeing drill bits). When the Reversing Switch is pressed to the (typically for driving fasteners or drilling holes).
  • Page 9 When drilling in a light gauge metal or wood, use wooden block to back up the material to prevent damage to the workpiece. Mark the center of the hole to be drilled with a center punch to give the drill bit a start and to prevent the bit from “walking.”...

  • Page 10: Cleaning And Maintenance

    Caution: Always disconnect this tool from its electrical power supply before performing any cleaning, servicing, or maintenance. Keep the Drill exterior free of oil or grease. Use only a mild soap and damp cloth when cleaning. Do not use a flammable or combustible solvent. Do not immerse this product in a liquid or allow a liquid to flow inside the tool.

  • Page 11: Please Read The Following Carefully

    PLEASE READ THE FOLLOWING CAREFuLLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.

  • Page 12: Parts & Assembly

    PARTS ASSEMBLY #19 Battery Charger (not shown) Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Rev 03a SKU 44849 For technical questions, please call 1-800-444-3353. Page 12...

  • Page 13: Electrical Schematic

    ELECTRICAL SCHEMATIC Rev 03a SKU 44849 For technical questions, please call 1-800-444-3353. Page 13...

  • Page 14: Limited 90-Day Warranty

    Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This...

Table of Contents