Chamberlain LiftMaster Security+ 970LM Owner's Manual

Models 970LM, 970US, 970MX, 970CN, 970CF, 970SP
The 900 Series remote control (Security✚
door openers and light controls having an orange "learn"
button and a yellow indicator light.
The additional push buttons can also activate other garage
door openers and/or light controls. (Instructions for pro-
gramming light products are included with those
accessories.)
Instructions are Described and Illustrated Below
1. Press and release the "learn" button on
the motor unit. The learn indicator light
will glow steadily for 30 seconds.
2. Within 30 seconds, press and hold the
button on the hand-held remote.
3. Release the button when the motor unit
light blinks. It has learned the code. If
light bulbs are not installed, two clicks
will be heard.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first erase all codes:
Press and hold the "learn" button on motor unit until the learn
indicator light goes out (approximately
6 seconds). All previous codes are now
erased. Reprogram each remote or keyless
entry you wish to use.
To Control the Opener Lights
In addition to operating the door, you may program the remote
to operate the lights.
1. With the door closed, press and hold the remote button that
you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener lights
should turn on or off but the door should not move.
114A2193G
3-Button Security✚
OWNER'S MANUAL
) works only with
®
9 1 9 1
7 3 7 3
5 5
KG KG
©2006, The Chamberlain Group, Inc.
All Rights Reserved
® Mini Remote Control
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
Open/Close/Stop Operation
NOTE: Not available with universal receiver.
Your Security✚ ® remote control can be programmed to operate
one door using all 3 buttons: the left button will only open the
door, the middle button will only close the door, and the third
button will stop the door's movement. You may set up this
feature as follows:
1. With the door closed, press and hold the
left remote push button.
2. Press and hold the Lock button on the
door control.
3. Press and hold the door control push bar.
When the opener lights flash, release all buttons. Test by
pressing the left (Open) button on the remote. The door should
open. Press it again while the door is open and nothing should
happen. Press the middle (Close) button and the door should
close. Press the third (Stop) button while the door is moving
and it should stop immediately.
The Remote Control Batteries
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
The lithium batteries should
produce power for up to
5 years. To replace, pry open
case as shown. Insert
batteries positive side up (+).
Dispose of old batteries
properly.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the fol-
lowing two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
WARNING
CAUTION
WARNING
CAUTION
Open Close
Stop