Chamberlain LiftMaster Professional 82LM Owner's Manual

The push buttons on the Two-Button remote controls can activate
garage door openers, entry ways and/or light controls.(Instructions for
programming light products are included with those accessories.)
Code switch remote controls are used when several persons are
operating the same device. Code switches must be set to
matching positions in all remote controls used to operate the
same receiver. Use the "smooth" push button exclusively for code
switch application. Follow the instructions described and shown
below.
Green
Test Light
Figure 1
Program smooth push button (Code switch
application)
1. Slide back the battery compartment cover on the bottom of the
remote control housing.
2. Place the old and new remote controls side by side. Make sure you
set code switches 1 through 9 in all remotes to matching positions
(Figure 2). Use a pen or screwdriver to move the switches to (+),
(-) or (0).
3. Replace the battery compartment cover.
Figure 2
Program ribbed push button (Green "learn" button)
1. Press and release the "learn" button on the motor
unit. The learn indicator light will glow steadily for
30 seconds.
2. Within 30 seconds, press and hold the ribbed
button on the hand-held remote.
3. Release the button when the motor unit light
blinks. It has learned the code. If light bulbs are
not installed, two clicks will be heard.
114A1649E
Model 82LM Two-Button Remote Control
OWNER'S MANUAL
Recommended for
code switch
applications
For use with green
"learn" button ONLY
Match code switches (1-9)
1
1
1
©2006, The Chamberlain Group, Inc.
To prevent possible SERIOUS INJURY or DEATH from a moving gate or
garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit
children to operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER
permit anyone to cross path of moving gate or door.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first erase all codes:
Press and hold the "learn" button on motor unit until
the learn indicator light goes out (approximately 6
seconds). All previous codes are now erased.
Reprogram each remote or keyless entry you wish
to use.
The Remote Control Battery
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
The 12V battery should produce power for at least a year. If the green
test light is dim or does not come on, replace
the battery.
To change the battery, slide back the battery
compartment cover. Position the new battery
as indicated. Replace the battery
compartment cover.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
2 3
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
9 1 9 1
7 3 7 3
5 5
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
2
Visor Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29C128
12V battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10A14
FOR SERVICE, DIAL OUR TOLL-FREE NUMBER:
2 3
1-800-528-2817
KG KG
All Rights Reserved
WARNING
CAUTION
AVERTISSEMENT
ATTENTION
WARNING
CAUTION
AVERTISSEMENT
ATTENTION
Replacement Parts
1 2 3
KG KG