TACO BELL STEAMER TBS-2X & TBS-1X OWNER INFORMATION (continued) Service/Technical Assistance Authorized Service Agency If you experience any problems with the installation Name: or operation of your unit, contact your local Roundup Phone No.: Authorized Service Agency. They can be found in the service agency directory packaged with the equipment.
TACO BELL STEAMER TBS-2X & TBS-1X IMPORTANT SAFETY INFORMATION Throughout this manual, you will find the following safety words and symbols that signify important safety issues with regards to operating or maintaining the equipment. WARNING WARNING GENERAL WARNING. Indicates informa- ELECTRICAL WARNING.
Page 5
TACO BELL STEAMER TBS-2X & TBS-1X IMPORTANT SAFETY INFORMATION (continued) • WARNING ELECTRICAL SHOCK HAZARD. • To ensure proper steaming characteristics, FAILURE TO FOLLOW THESE INSTRUCTIONS some mineral deposits must be present on COULD RESULT IN SERIOUS INJURY OR generator surface. If, during cleaning, the DEATH.
TACO BELL STEAMER TBS-2X & TBS-1X SPECIFICATIONS Electrical Ratings WARNING All electrical connections must be in accordance Model and Voltage Watts Amps Hertz with local electrical codes and any other appli- Manufacturing Number cable codes. TBS-2X 3300 15.9 50/60 WARNING 9100400 ELECTRICAL SHOCK HAZARD.
TACO BELL STEAMER TBS-2X & TBS-1X INSTALLATION Unpacking CAUTION All electrical connections must be in accordance 1. Remove unit and all packing materials from ship- with local electrical codes and any other appli- ping carton. cable codes. 2. The box should contain the following: •...
Page 8
TACO BELL STEAMER TBS-2X & TBS-1X INSTALLATION (continued) CAUTION WARNING Water pressure must not exceed 30 psi (2.1 kg/ ELECTRICAL SHOCK HAZARD. cm 2 or 207 kPa). Higher water pressures may BE SURE TO READ ALL INFORMATION AND FOL- cause poor performance or flooding. To reduce...
TACO BELL STEAMER TBS-2X & TBS-1X INSTALLATION (continued) NOTE: If steamer does not steam properly after cali- 8. With the unit positioned at the edge of its location bration, refer to the Troubleshooting section of this surface (Edge of the counter, table, etc.) slide the manual.
TACO BELL STEAMER TBS-2X & TBS-1X OPERATION (continued) Operating Instructions IMPORTANT: Steam generator must be calibrated ����� Rocker Switch (Power On/Off) before initial use. See the section titled Calibration in the Installation section of this manual. 1. Turn on the Rocker Switch (power On/Off) (Figure 3).
TACO BELL STEAMER TBS-2X & TBS-1X MAINTENANCE WARNING Turn the unit off, disconnect the power source Chimney and allow the unit to cool down before performing any service or maintenance on the unit. The TBS- 2X has two power cords. Make sure both cords are disconnected.
TACO BELL STEAMER TBS-2X & TBS-1X MAINTENANCE (continued) Monthly Maintenance 10. Clean Steam Chamber free of any product spills. 11. Clean unit surface with a hot, clean, damp cloth Your steamer utilizes an open steam generator. Water (not dripping wet) and wipe dry.
Page 13
TACO BELL STEAMER TBS-2X & TBS-1X MAINTENANCE (continued) Slanted end of tube Figure 5. Installing Calibration Tubes Figure 6. Water Measurement 5. Turn the Rocker Switch (power On/Off) to ON. 6. Press the Cycle Start button and operate the unit through two complete cycles to purge all air from the tubes.
TACO BELL STEAMER TBS-2X & TBS-1X TROUBLESHOOTING WARNING To avoid possible personal injury and/or damage to the unit, inspection, test and repair of electrical equip- ment should be performed by qualified service personnel. The unit should be unplugged when servicing, except when electrical tests are required.
Page 15
TACO BELL STEAMER TBS-2X & TBS-1X TROUBLESHOOTING (continued) Problem Possible Cause(s) Corrective Action Unit only leaks water when pow- Solenoid Valve is leaking due Disassemble the Solenoid Valve and clean ered off. to debris trapped within its out the plunger. Reassemble and test. If the plunger and seat.
LIMITED WARRANTY Equipment manufactured by A.J. Antunes & Co. Foodservice Equipment has been constructed of the finest materials available and manufactured to high quality standards. These units are warranted to be free from mechanical and electrical defects for a period of one year from date of purchase or 18 months from shipment from factory, whichever occurs first, under normal use and service, and when installed in accordance with manufacturer’s recommendations.