Related Manuals for Inglis IGS326RD0
Summary of Contents for Inglis IGS326RD0
- Page 1 9760030 Table of Contents ............Q© IMPORTANT: Save installation instructions for local electrical inspector's use. 9760030...
- Page 2 TABLEOF CONTENTS RANGE SAFETY ................iNSTALLATiON REQUIREMENTS ..........Tools and Parts ................Location Requirements .............. Electrical Requirements ............Gas Supply Requirements ............INSTALLATION INSTRUCTIONS ..........Unpack Range ................install Anti-Tip Bracket .............. Verify Anti-Tip Bracket Location ..........9 Level Range ................Make Gas Connection ..............
- Page 3 WARNING: For your safety, the information in this manuam must be followed to minimize_ the risk of fire or explosion, or to prevent property damage, persona_ injury, or death. - Do not store or use gasoline or other flammaHe vapors and _iquids in the vicinity of this or any other...
- Page 4 (NSTALLATION REQUIREMENTS Assemble the required tools and parts before starting installation. IMPORTANT: Observe all governing codes and ordinances. Do Read and follow the safety instructions provided with any tools not obstruct flow of combustion and ventilation air. listed here. It is the instaUer's responsibility to comply with installation Tools needed clearances specified on the model/serial rating plate.
- Page 5 ProductDimensions Installation Clearances Cabinet opening dimensions shown are for 25" (64 cm) countertop depth, 24" (61 cm) base cabinet depth and 36" (91.4 cm) counte_top height= If the cabinet depth is greater than 24" (6! cm) oven frame must extend beyond cabinet fronts by 1/2"(13 mm) minimum= For minimum 13"...
- Page 6 Electrical Shock Hazard Explosion Hazard Plug intoa grounded 3 prong outlet. Use a new AGA or CSA approved gas supply line. Donotremove ground prong. Securely tighten aH gas connections. Donotuseanadapter. If connected to LP, have a qualified person make sure gas pressure does not exceed 14"...
- Page 7 Fmexib_emetal appliance connector: Burner _nput Requirements if local codes permit, a new A.GaA./CaSaA.design-certified, 4 - 5 ft (122 - 152.4 cm) long, !/2" (1.3 cm) ors/4'' (1.9 cm) LD. Input ratings shown on the model/serial rating plate are for flexible metal appliance connector may be used for elevations up to 2,000 ft (609.6 m).
- Page 8 iNSTALLATiON iNSTRUCTiONS If countertop is not flush with cabinet opening edge, Nigh template with overhang. 1. Remove shipping materials, tape and protective film from range. Keep cardboard bottom under range. Remove oven If cabinet opening is wider than specified in the "Location racks and parts package from inside oven.
- Page 9 Typical rigid pipe connection A combination of pipe fittings must be used to connect the range to the existing gas line. Your connections may be different, according to the supply line type, size and location, 1, Apply pipe-joint compound made for use with LP gas to all pipe thread connections, 2, Using a pipe wrench to tighten, connect the gas supply to the range.
- Page 10 Complete Connection Check Operation of Cooktop Burners 1, Check that the gas pressure regulator shutoff valve is in the "on" position, Standard Surface Burners Push in and turn each control knob to the "LFE" position, The flame should light within 4 seconds. The first time a burner is lit it may take longer than 4 seconds to light because of air in the gas line, if burners...
- Page 11 clean and soft in character. No yellow tips, blowing or lifting of flame should occur. CheckOperation of OvenBakeBurner If flame needs to be adjusted: 1° Remove theoven rack, T oremove thebake burner cover: 1. Loosen the lock screw on the air shutter located at the rear of Remove twoscrews attherear o ftheoven bottom.
- Page 12 GASCONVERSIONS Remove storage drawer or warming drawer. Locate gas pressure regulator at rear of storage or warming drawer compartment. NOTE: On models with a warming drawer, an access cover must be removed from the gas pressure regulator. Explosion Hazard Use a new AGA or CSA approved gas supply line.
- Page 13 To Convert Standard Surface Burners To Convert Oven Bake Burner 1. Remove burner cap. 1. Remove oven racks. 2. Use a 1/2"combination wrench to turn the orifice hood down 2. Using a T20 Torx screwdriver, remove the burner base. snug onto pin (about 2 to 21/2turns). NOTE: Reinstall one of the screws through the range cooktop to hold orifice spud holder in place while removing IMPORTANT: Do not overtighten.
- Page 14 IMPORTANT: You may have to adjust the "LO" setting for Gas pressure regulator each cooktop burner. 3. Remove plastic cover from gas pressure regulator cap. Checking for proper cooktop, bake and broil burner flames is 4. Turn gas pressure regulator cap (marked "LP" on front of gas very important.
- Page 15 Gas orifice spuds are stamped with a number on the side. To Convert Oven Broil Burner Replace the LP gas orifice spud with the correct Natural gas orifice spud. Use a 1/2"combination wrench to loosen the orifice hood away from the pin (about 2 to 21/2turns). The oven broil burner flame cannot be properly adjusted if this conversion is not made.
- Page 16 9760030 @ 2004 6/04 Printed in U.SA AH rights reserved...