KVH Industries TracVision M5 User Manual

KVH Industries TracVision M5 User Manual

Gyrotrac configuration
Hide thumbs Also See for TracVision M5:
Table of Contents

Advertisement

TracVision M5/M7
GyroTrac
Configuration

Advertisement

Table of Contents
loading

Summary of Contents for KVH Industries TracVision M5

  • Page 1 TracVision M5/M7 GyroTrac Configuration ™...
  • Page 2 GyroTrac Configuration User’s Guide This user’s guide provides all of the basic information you need to operate, set up, and troubleshoot the TracVision M5/M7 satellite TV antenna system. For detailed installation information, please refer to the TracVision M5/M7 Installation Guide.
  • Page 3 TracVision and KVH are registered trademarks of KVH Industries, Inc. The unique light-colored dome with dark contrasting base is a registered trademark of KVH Industries, Inc. DVB (Digital Video Broadcasting) is a registered trademark of the DVB Project. DIRECTV is an official trademark of DIRECTV, Inc.
  • Page 4: Table Of Contents

    TracVision M5/M7 User’s Guide Table of Contents Table of Contents Introduction Using this Manual ................3 System Overview................6 Circular and Linear Versions..............9 Operation Receiving Satellite TV Signals ............13 Turning the System On/Off ..............14 Changing Channels and Switching Between Satellites (Circular Versions) ................15 Changing Channels and Switching Between Satellites (Linear Versions)................21...
  • Page 5 Recalibration Recalibrating the System..............87 Setting the Sensor Offset Values .............94 TracVision M5 Wiring Diagrams TracVision M5 Wiring Diagram for One or Two Receivers ....99 TracVision M5 Wiring Diagram for Three or Four Receivers (Circular Versions Only)*................100 TracVision M7 Wiring Diagrams TracVision M7 Wiring Diagram for One or Two Receivers .....103...
  • Page 6 TracVision M5/M7 User’s Guide Chapter 1 - ADCU Wiring Diagrams ADCU Wiring Diagram (Required) ..........109 ADCU Wiring Diagram (Optional Equipment) .........110 Position Grids European Position Grid ..............113 North American Position Grid ............114...
  • Page 7 TracVision M5/M7 User’s Guide Chapter 1 - Introduction 1. Introduction This chapter provides a basic overview of this manual and your TracVision system. Contents Using this Manual.............. 3 System Overview............... 6 Circular and Linear Versions..........9...
  • Page 8: Introduction

    This manual provides complete operation, setup, and troubleshooting information for your TracVision system, as well as wiring diagrams for various TracVision M5/M7 configurations. Who Should Use This Manual The user should refer to the “Operation” chapter to learn how to operate the system.
  • Page 9 TracVision M5/M7 User’s Guide Chapter 1 - Introduction Typographical Conventions This manual uses the following typographical conventions: Text Example Description <SAT NAME> Text in brackets or the pound sign (#) indicates a variable portion of the Advanced Digital Control Unit (ADCU) display...
  • Page 10 TracVision M5/M7 User’s Guide Chapter 1 - Introduction Related Documentation In addition to this User’s Guide, the following documents are provided with your TracVision system: Document Description Installation Guide Complete product installation instructions Product Registration Form Details on registering the product...
  • Page 11: System Overview

    Plotters Radars Remote Displays TIP: TracVision M5 receiver wiring diagrams are provided in Appendix C on page 97. TracVision M7 receiver wiring diagrams are provided in Appendix D on page 101. ADCU wiring diagrams are provided in Appendix E on page 107.
  • Page 12 TracVision M5/M7 User’s Guide Chapter 1 - Introduction System Components The TracVision M5/M7 includes the following components: Antenna Unit The antenna unit houses the antenna positioning mechanism, LNB (low noise block), and control elements within a radome. Weathertight connectors join the power, signal, and control cabling from the belowdecks units.
  • Page 13 TracVision M5/M7 User’s Guide Chapter 1 - Introduction System Features Your TracVision M5/M7 uses integrated DVB technology to quickly acquire and track the correct satellite, switch between your selected satellites, and send TV signals to the receiver. In-motion Tracking The TracVision system uses a state-of-the-art, actively stabilized antenna.
  • Page 14: Circular And Linear Versions

    TracVision M5/M7 User’s Guide Chapter 1 - Introduction Circular and Linear Versions Your TracVision system is configured to receive either circularly polarized satellite signals (e.g., North America) or linearly polarized satellite signals (e.g., Europe or Latin America). Figure 1-3 illustrates the difference between these two polarizations.
  • Page 15 TracVision M5/M7 User’s Guide Chapter 1 - Introduction The correct skew setting varies depending on your geographic location, since the orientation of your antenna to the satellite changes as you move. For example, if your antenna is tracking the PAS 9 satellite for Sky Mexico programming, the ideal skew setting ranges from +30 to +70, depending upon your location within the satellite’s...
  • Page 16: Operation

    TracVision M5/M7 User’s Guide Chapter 2 - Operation 2. Operation This chapter explains everything you need to know to operate the TracVision system. Contents Receiving Satellite TV Signals ......... 13 Turning the System On/Off ..........14 Changing Channels and Switching Between Satellites (Circular Versions) ............
  • Page 17: Receiving Satellite Tv Signals

    TracVision M5/M7 User’s Guide Chapter 2 - Operation Receiving Satellite TV Signals Television satellites are located in fixed positions above the Earth’s equator and beam TV signals down to certain regions of the planet (not worldwide). To receive TV signals from a satellite, you must be located within that satellite’s unique coverage area.
  • Page 18: Turning The System On/Off

    TracVision M5/M7 User’s Guide Chapter 2 - Operation Turning the System On/Off Since power to the TracVision system is controlled by the vessel power, you can turn the system on or off by applying/removing vessel power. Turning On the System Follow the steps below to turn on your TracVision system.
  • Page 19: Changing Channels And Switching Between Satellites (Circular Versions)

    TIP: The primary receiver is the receiver connected to the antenna’s RF1 connector. DISH 1000 When the TracVision M5/M7 system is configured for DISH 1000, you can view the DISH HDTV programming for your geographic area. You can configure the system for either DISH 1000/61 or DISH 1000/129 use.
  • Page 20 TracVision M5/M7 User’s Guide Chapter 2 - Operation DISH 1000 Automatic Mode - Preferred for One or Two Receivers The antenna switches between satellites automatically as you change channels using the primary receiver’s remote control. The primary receiver is the receiver connected to the antenna’s RF1 cable (see Figure 2-6 and Figure 2-7).
  • Page 21 TracVision M5/M7 User’s Guide Chapter 2 - Operation DISH 1000 Manual Mode - Required for Three or More Receivers Since multiswitches interfere with communications between the receivers and the antenna, the system must be set up in Manual mode when three or more receivers are installed. When Manual mode is enabled, you can switch between your selected satellites using the buttons on the front of the ADCU (see Figure 2-8 and Figure 2-9).
  • Page 22 TracVision M5/M7 User’s Guide Chapter 2 - Operation Dual-Sat Mode - DISH 500, ExpressVu, DIRECTV, and Custom Dual-Sat Setups Dual-Sat Mode is used with several service configurations. Figure 2-10 lists each Dual-Sat service configuration, the satellites tracked for each service, and the available satellite switching modes.
  • Page 23 TracVision M5/M7 User’s Guide Chapter 2 - Operation Dual-Sat Automatic Mode - Preferred Mode for One or Two Receivers* The antenna switches between satellites automatically while you change channels using the primary receiver’s remote control. The primary receiver is the receiver connected to the antenna’s RF1 cable (see Figure 2-11 and Figure 2-12).
  • Page 24 Dual-Sat Manual Mode - Required for Three or More Receivers and All Custom Dual-Sat Setups Circular TracVision M5/M7 systems with three or more receivers require the use of a multiswitch. Since multiswitches interfere with communications between the receivers and the antenna, the system must be set up in Manual mode.
  • Page 25: Changing Channels And Switching Between Satellites (Linear Versions)

    TracVision M5/M7 User’s Guide Chapter 2 - Operation Changing Channels and Switching Between Satellites (Linear Versions) During installation, your TracVision system should have been set up to track the satellite(s) of your choice and the channel guides for your selected satellite service should have been downloaded.
  • Page 26 TracVision M5/M7 User’s Guide Chapter 2 - Operation Automatic Satellite Switching Most TracVision systems switch between satellites automatically while you change channels using the primary receiver’s remote control. The primary receiver is the receiver connected to the antenna’s RF1 cable (see Figure 2-15 and Figure 2-16). If an optional secondary receiver is connected, you can use its remote control to switch between the channels on the currently selected satellite.
  • Page 27 TracVision M5/M7 User’s Guide Chapter 2 - Operation Manual Satellite Switching If the TracVision system includes a multiswitch, you can use the receivers’ remote controls to change channels on the currently selected satellite. If you need to switch satellites, simply use the buttons on the front of the ADCU (see Figure 2-17 and Figure 2-18).
  • Page 28: Receiver Requirements

    TracVision M5/M7 system and explains linear and circular receiver setup requirements. Circular Receiver Compatibility To ensure compatibility with your TracVision M5/M7 system, be sure to use a KVH-validated receiver for your selected service type (see Figure 2-19).
  • Page 29 Chapter 2 - Operation DISH Network/ExpressVu Receiver Configuration If your TracVision M5/M7 system is set up for DISH Network or ExpressVu service, your receiver(s) should have also been configured during installation. In most cases, you do not need to reconfigure your receiver(s).
  • Page 30: Adcu Display Types

    “Changing Display Types” on page 28. Antenna The antenna display type is the TracVision M5/M7 system’s default display type. When the ADCU is set to the antenna display type, satellite tracking information is displayed.
  • Page 31 TracVision M5/M7 User’s Guide Chapter 2 - Operation Pitch, Roll, and Yaw The pitch, roll, and yaw display type displays the vessel’s pitch, roll, and yaw values. Figure 2-25 Pitch, Roll, and Yaw Screen Pitch Roll #.#˚ #.#˚ #.#˚ Rate of Turn The rate of turn display type displays the vessel's magnetic heading and rate of turn values.
  • Page 32 TracVision M5/M7 User’s Guide Chapter 2 - Operation Changing Display Types Use the flowchart in Figure 2-28 if you wish to change the display type. Figure 2-28 Changing Display Types <Default Display> Menu Setup display type? Enter Next Return Compass?
  • Page 33: Product Care

    TracVision M5/M7 User’s Guide Chapter 2 - Operation Product Care Please consider the following antenna care guidelines for maintaining peak performance: • Periodically wash the exterior of the antenna dome with fresh water and mild detergent. Avoid harsh cleansers and volatile solvents (such as acetone) and do not spray the dome directly with high-pressure water.
  • Page 34: Settings

    TracVision M5/M7 User’s Guide Chapter 3 - Settings 3. Settings This chapter contains information on system settings and how to modify them using the ADCU. Contents Manually Setting Latitude and Longitude ......33 Setting the LNB Skew Angle (Linear Versions Only)..34 Connecting a PC ..............
  • Page 35: Manually Setting Latitude And Longitude

    TracVision M5/M7 User’s Guide Chapter 3 - Settings Manually Setting Latitude and Longitude When a GPS receiver is detected, the TracVision system does not require manually set latitude and longitude values. However, if an active GPS is not connected, you can use the flowchart in Figure 3-1 to manually set the latitude and longitude values in the antenna, which will speed up satellite acquisition.
  • Page 36: Setting The Lnb Skew Angle (Linear Versions Only)

    TracVision M5/M7 User’s Guide Chapter 3 - Settings Setting the LNB Skew Angle (Linear Versions Only) To optimize satellite signal reception, you need to adjust the skew angle on the LNB whenever you change your geographic location or change which satellites are set up for tracking.
  • Page 37 TracVision M5/M7 User’s Guide Chapter 3 - Settings Determining the Skew Angle Use the flowchart in Figure 3-2 to determine the skew angle of the currently selected satellite using the ADCU. NOTE: If you wish to determine the average skew for two or three satellites, determine the skew angle for each satellite by performing the procedure below, then divide by the number of installed satellites.
  • Page 38 TracVision M5/M7 User’s Guide Chapter 3 - Settings Adjusting the Skew Angle Once you have determined the proper skew angle, follow the steps below to adjust the antenna’s LNB skew angle. CAUTION To avoid bodily injury, be sure to turn off the antenna and disconnect power to all wired components.
  • Page 39 3. Using a 2 mm allen hex key, loosen the two M4 socket set screws securing the LNB. The location of the screws varies according to TracVision model; refer to Figure 3-4 or Figure 3-5. Figure 3-4 TracVision M5 Set Screws Reflector M4 Socket Set Screws...
  • Page 40 TracVision M5/M7 User’s Guide Chapter 3 - Settings 4a. TracVision M5 Only - Adjust the LNB clockwise or counter-clockwise, until the skew arrow on the LNB points to the skew angle that you determined earlier. Due to physical constraints, if the skew angle is greater than +15°, you need to subtract 180 to get the...
  • Page 41 TracVision M5/M7 User’s Guide Chapter 3 - Settings 4b. TracVision M7 Only - Adjust the LNB clockwise or counter-clockwise, until the skew arrow on the LNB points to the skew angle that you determined earlier. IMPORTANT! Be sure to keep the LNB fully inserted in the choke feed to ensure optimum performance.
  • Page 42: Connecting A Pc

    Connecting a PC Follow the instructions below if you need to connect a PC to the TracVision M5/M7 system. This procedure requires a PC with Windows HyperTerminal (or equivalent) and a serial data cable. TIP: If you are a KVH-authorized technician, you can use the KVH Flash Update Wizard instead of HyperTerminal.
  • Page 43 TracVision M5/M7 User’s Guide Chapter 3 - Settings 2. Open HyperTerminal and establish the following settings: • Bits per second: 9600 • Data bits: 8 • Parity: None • Stop Bits:1 • Flow Control: None Figure 3-9 HyperTerminal Settings TIP: To view characters on the screen as you type, set up HyperTerminal to echo typed characters.
  • Page 44: Dish 1000 Setup

    TracVision M5/M7 User’s Guide Chapter 3 - Settings DISH 1000 Setup This section explains how to configure the TracVision system for DISH Network’s three-satellite service. For operation instructions and additional information on DISH modes, refer to “Changing Channels and Switching Between Satellites (Circular Versions)” on page 15.
  • Page 45 TracVision M5/M7 User’s Guide Chapter 3 - Settings Step 2 - Update Latitude and Longitude Data (if necessary) If you do not have a GPS connected to the ADCU, you need to enter your vessel’s latitude and longitude into the system.
  • Page 46 TracVision M5/M7 User’s Guide Chapter 3 - Settings Step 3 - Configure the Receiver(s) NOTE: If you are connecting multiple receivers, repeat this process for each additional receiver. You will need to connect each receiver, one at a time, to the RF1 cable and perform the steps below.
  • Page 47 TracVision M5/M7 User’s Guide Chapter 3 - Settings 8. After waiting 15 minutes, repeat Steps 4-6 to run a second Check Switch test. 9. Verify the values on your TV match those required for your selected DISH 1000 configuration (see Figure 3-13 and Figure 3-14).
  • Page 48: Dual-Sat Or Single Satellite Setups

    Excessive motion or satellite blockage can prevent proper configuration. NOTE: Be sure to only install satellites that your TracVision M5/M7 system can track in your geographic location. For your convenience, KVH provides links to several websites that offer satellite coverage information. Simply visit...
  • Page 49 TracVision M5/M7 User’s Guide Chapter 3 - Settings Step 1 - Select Satellites You can select up to two satellites from either the circular satellite library (see Figure 3-15) or the linear satellite library (see Figure 3-16 on page 48).
  • Page 50 TracVision M5/M7 User’s Guide Chapter 3 - Settings Figure 3-16 Linear Satellite Library Satellite Location Satellite Installation Name 26.0° E Arabsat ARABSAT 19.2° E Astra 1 ASTRA1 28.2° E Astra 2N ASTRA2N 28.2° E Astra 2S ASTRA2S 7.0° E Eutelsat W3A EUTEL_W3A 30.0°...
  • Page 51 TracVision M5/M7 User’s Guide Chapter 3 - Settings Step 2 - Configure the TracVision System Now you need to configure the TracVision system to track your selected satellites. Use the flowchart in Figure 3-17 to configure your selected satellite(s). TIP: For your convenience, you can determine your approximate latitude and longitude using the Position Grids provided in Appendix F on page 111.
  • Page 52 TracVision M5/M7 User’s Guide Chapter 3 - Settings Step 3 - Configure the Receiver(s) (if required) Linear configurations without a multiswitch, DISH Network, and ExpressVu subscribers require receiver configuration. The following sections explain how to configure the receiver(s) for TracVision use.
  • Page 53 TracVision M5/M7 User’s Guide Chapter 3 - Settings 6. Wait at least 15 minutes before proceeding. Disregard messages on the TV stating the test is complete; you must wait 15 minutes before proceeding. IMPORTANT! Please be patient. The Check Switch test takes approximately 15 minutes to complete.
  • Page 54: European Tri-Sat Mode Setup

    TracVision M5/M7 User’s Guide Chapter 3 - Settings European Tri-Sat Mode Setup This section explains how to configure the TracVision system to track three satellites within predefined linear satellite groups for European locations. Each group includes three satellites (see Figure 3-21). For operation instructions, refer to “Changing Channels and Switching...
  • Page 55 TracVision M5/M7 User’s Guide Chapter 3 - Settings Step 1 - Configure the TracVision System Follow the steps below to set up the TracVision system for your desired European Tri-Sat Mode. You will enter PC commands into the HyperTerminal window. An example is provided in Figure 3-22.
  • Page 56 TracVision M5/M7 User’s Guide Chapter 3 - Settings Step 2 - Update Latitude and Longitude Data (if necessary) If you do not have a GPS connected to the ADCU, you need to enter your vessel’s latitude and longitude into the system.
  • Page 57: Setting Instant On Mode

    TracVision M5/M7 User’s Guide Chapter 3 - Settings Setting Instant On Mode When Instant On mode is enabled, the antenna can immediately receive signals on startup if the vessel has not moved since the antenna was last shut off. However, if the system is turned off, then the vessel...
  • Page 58: Setting Sleep Mode

    TracVision M5/M7 User’s Guide Chapter 3 - Settings Setting Sleep Mode When the vessel has come to a stop and holds its position for one minute (e.g., at a dock), the antenna unit enters Sleep Mode, which locks the antenna in place to conserve power. As soon as the vessel moves beyond a 1°...
  • Page 59: Adjusting Display Brightness

    TracVision M5/M7 User’s Guide Chapter 3 - Settings Adjusting Display Brightness You can adjust the brightness of the ADCU’s LCD screen to suit your preferences. Use the flowchart in Figure 3-26 if you wish to adjust the display brightness. Figure 3-26 Setting Display Brightness <Default Display>...
  • Page 60: Restarting The Tracvision System

    TracVision M5/M7 User’s Guide Chapter 3 - Settings Restarting the TracVision System Use the flowchart in Figure 3-27 if you wish to restart the TracVision system. Figure 3-27 Restarting the TracVision System <Default Display> Menu Setup display type? Enter Next Return Select Next until “Control...
  • Page 61: Troubleshooting

    TracVision M5/M7 User’s Guide Chapter 4 - Troubleshooting 4. Troubleshooting This chapter identifies potential basic problems along with their possible causes and solutions. It also explains how to get technical support. Contents Five Simple Checks ............61 Error Messages ............... 62 Troubleshooting Matrix............
  • Page 62: Five Simple Checks

    TracVision M5/M7 User’s Guide Chapter 4 - Troubleshooting Five Simple Checks If you are experiencing a problem receiving satellite TV with your TracVision system, perform the five simple checks below. TIP: You can also try resetting the satellite TV receiver. Turn off and unplug the receiver, wait one minute, then plug it back in and turn it back on.
  • Page 63: Error Messages

    The “No GPS data while system powerup” message is not a true error message. This indicates that no GPS was detected during TracVision M5/M7 initialization. If no GPS receiver is connected, or if the GPS receiver was not initialized prior to turning on the TracVision system, some navigational display types will be unavailable.
  • Page 64 TracVision M5/M7 User’s Guide Chapter 4 - Troubleshooting TV Comms is Off No Data from Antenna The “TV comms is off no data from antenna” error message indicates a communication failure between the ADCU and the antenna. This is usually the result of either the antenna being disconnected from the ADCU or the antenna not being turned on.
  • Page 65: Troubleshooting Matrix

    TracVision M5/M7 User’s Guide Chapter 4 - Troubleshooting Troubleshooting Matrix The troubleshooting matrix in Figure 4-1 identifies potential operational symptoms and their causes and remedies. “Causes and Remedies for Operational Issues” on page 65 contains detailed information on the causes and remedies listed below.
  • Page 66: Causes And Remedies For Operational Issues

    Causes and Remedies for Operational Issues This section addresses the most common operational issues that can affect the performance of the TracVision M5/M7 system. If your TracVision system requires service, you can visit any KVH-authorized dealer or distributor for assistance. To find a KVH-authorized dealer near you, visit www.kvh.com/wheretogetservice.
  • Page 67 TracVision M5/M7 User’s Guide Chapter 4 - Troubleshooting Satellite Coverage Issue Television satellites are located in fixed positions above the Earth’s equator and beam TV signals down to certain regions of the planet (not worldwide). To receive TV signals from a satellite, you must be located within that satellite’s unique coverage area.
  • Page 68 Refer to the TracVision M5 wiring diagrams in Appendix C on page 97 or the TracVision M7 wiring diagrams provided in Appendix D on page 101. You can also refer to the TracVision M5/M7 Installation Guide for complete system wiring information, or visit any KVH-authorized dealer or distributor for assistance.
  • Page 69 If your TracVision system’s configuration requires a multiswitch, an active (powered) multiswitch must be used to ensure proper antenna performance. Refer to the M5 Wiring Diagrams in Appendix C on page 97 or the M7 Wiring Diagrams in Appendix D on page 101 for detailed information.
  • Page 70: Technical Support

    TracVision M5/M7 User’s Guide Chapter 4 - Troubleshooting Technical Support The TracVision M5/M7 antenna is a sophisticated electronic device. KVH-authorized technicians have the specialized tools and expertise necessary to diagnose and repair a system fault. Therefore, if you experience any operating problem or require technical assistance, please call or visit your local authorized TracVision dealer or distributor.
  • Page 71: Setting The Heading Reference Source

    TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions Appendix A Advanced Settings and Functions This appendix contains information on advanced settings and functions. This information should only be utilized by KVH-authorized technicians. Contents Data Output Settings ............73 Setting the Heading Reference Source ......
  • Page 72: Data Output Settings

    TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions Data Output Settings This section explains how to modify the GyroTrac sensor’s data output settings. Overview The TracVision system’s GyroTrac sensor transmits up to five selectable message types simultaneously to external navigation devices connected to the ADCU.
  • Page 73 TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions Use the flowchart in Figure A-1 to modify the sine/cosine data output settings, or restore the original sine/cosine settings. NOTE: If an active GPS connection is not detected, “Only Mag Available” is displayed.
  • Page 74 TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions Serial Port Outputs Serial ports 1 and 2 can be individually programmed to output any of the message formats described in this section (serial port 3 is disabled when a TracVision system is connected to the ADCU). Up to four NMEA 0183 listening devices can be connected to each of the serial ports.
  • Page 75 TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions Use the flowchart in Figure A-2 to modify the serial output settings, or if you wish to restore the original output settings. Figure A-2 Serial Output Settings <Default Display>...
  • Page 76: Setting The Heading Reference Source

    TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions Setting the Heading Reference Source You can set the heading reference source to internal (default) or external. When internal heading data is selected, the system receives heading data from the GyroTrac’s sensor. You can select external heading data if an external compass is connected to the system.
  • Page 77: Manually Controlling The Antenna

    TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions Manually Controlling the Antenna Use the flowchart in Figure A-4 if you wish to manually control the antenna. NOTE: If you are performing this procedure as part of a satellite frequency scan update procedure, be sure to select “NO”...
  • Page 78: Updating Satellite Frequency Data

    TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions Updating Satellite Frequency Data If the antenna is unable to find a satellite, or if you are unable to receive certain channels, the satellite’s frequency data might have changed. The satellite frequency scan feature allows you to update the frequency data of any satellite stored in the system’s library.
  • Page 79 TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions 5. Use the flowchart in Figure A-5 to scan the frequency data of the selected satellites. TIP: Scanning satellite frequencies might take up to 10 minutes. Figure A-5 Scanning Frequency Data Select - or + as required, <Default Display>...
  • Page 80: Displaying The Calibration Score

    TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions Displaying the Calibration Score Use the flowchart in Figure A-6 to display the calibration score. For information on interpreting the calibration score, see “Interpreting the Calibration Score” on page 92.
  • Page 81: Displaying The Antenna Software Version

    TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions Displaying the Antenna Software Version Use the flowchart in Figure A-7 if you wish to display the antenna software version. Figure A-7 Displaying the Antenna Software Version <Default Display>...
  • Page 82: Displaying The Antenna Serial Number

    TracVision M5/M7 User’s Guide Appendix A - Advanced Settings and Functions Displaying the Antenna Serial Number Use flowchart in Figure A-8 if you wish to display the antenna serial number. Figure A-8 Displaying the Antenna Serial Number <Default Display> Menu...
  • Page 83: Recalibration

    TracVision M5/M7 User’s Guide Appendix B - Recalibration Appendix B Recalibration This appendix explains how to recalibrate the system and set gyro offset values. This information should only be utilized by KVH-authorized technicians. Contents Recalibrating the System ..........87 Setting the Sensor Offset Values........94...
  • Page 84: Recalibrating The System

    TracVision M5/M7 User’s Guide Appendix B - Recalibration Recalibrating the System During installation, the TracVision M5/M7 system should have been properly calibrated. However, if the GyroTrac sensor is moved to another location, or if additional metallic equipment is installed or removed near the GyroTrac sensor, KVH recommends recalibrating the system.
  • Page 85 TracVision M5/M7 User’s Guide Appendix B - Recalibration Step 1 - Clear the Existing Calibration Score Use the flowchart in Figure B-1 to clear the existing calibration score. NOTE: If the “System Halted Power System Off/On” message is displayed during this procedure, turn the system off, wait 10 seconds, then turn the system on.
  • Page 86 TracVision M5/M7 User’s Guide Appendix B - Recalibration Step 2 - Set Autocalibration to On Use the flowchart in Figure B-2 to turn on autocalibration. Figure B-2 Setting Autocalibration to On <Default Display> Menu Setup display type? Enter Next Return Select Next until “Control...
  • Page 87 TracVision M5/M7 User’s Guide Appendix B - Recalibration Step 3 - Recalibrate the System a. Select a calm day and a clear area. Excessive pitching and rolling can distort calibration data. b. Write down your approximate heading. You will use this information later in this procedure.
  • Page 88 TracVision M5/M7 User’s Guide Appendix B - Recalibration Step 4 - Verify the Calibration Score This section explains how to display and interpret the calibration score. Be sure to verify that the calibration yielded acceptable results. If the calibration did not yield acceptable results, you will need to restart recalibration.
  • Page 89 TracVision M5/M7 User’s Guide Appendix B - Recalibration Interpreting the Calibration Score Each calibration results in a calibration score that is stored in the system’s memory. The calibration score contains an accuracy rating, a magnetic environment rating, and the number of calibrations performed.
  • Page 90 TracVision M5/M7 User’s Guide Appendix B - Recalibration Step 5 - Set Autocalibration to Off Use the flowchart in Figure B-7 to turn off autocalibration. Figure B-7 Setting Autocalibration to Off <Default Display> Menu Setup display type? Enter Next Return Select Next until “Control...
  • Page 91: Setting The Sensor Offset Values

    TracVision M5/M7 User’s Guide Appendix B - Recalibration Setting the Sensor Offset Values The GyroTrac sensor must be mounted as close to level in pitch and roll as possible, with its long axis parallel to the vessel’s centerline. If the GyroTrac sensor was not mounted according to the guidelines in...
  • Page 92 TracVision M5/M7 User’s Guide Appendix B - Recalibration Figure 3 Setting Sensor Offset Values <Default Display> Set brightness? Menu Next Return Select Next until “Set Gyro Setup display type? offsets?” is Enter Next Return displayed. Set Gyro offsets? Next Return...
  • Page 93: Tracvision M5 Wiring Diagrams

    Appendix C TracVision M5 Wiring Diagrams This appendix provides receiver wiring diagrams for basic TracVision M5 configurations. Wiring diagrams vary according to the number of receivers installed and the TracVision system configuration (circular/ linear). For installation instructions, refer to the Installation Guide.
  • Page 94: Tracvision M5 Wiring Diagram For One Or Two Receivers

    TracVision M5/M7 User’s Guide Appendix C - TracVision M5 Wiring Diagrams TracVision M5 Wiring Diagram for One or Two Receivers Vessel Power Antenna (12 VDC) Data ADCU 60 59 48 47 Yellow Label Red Label DB9 Maintenance Port Green Label...
  • Page 95: Tracvision M5 Wiring Diagram For Three Or Four Receivers (Circular Versions Only)

    TracVision M5/M7 User’s Guide Appendix C - TracVision M5 Wiring Diagrams TracVision M5 Wiring Diagram for Three or Four Receivers (Circular Versions Only)* Vessel Power Antenna (12 VDC) Data ADCU 60 59 48 47 Yellow Label Red Label DB9 Maintenance Port...
  • Page 96: Tracvision M7 Wiring Diagrams

    TracVision M5/M7 User’s Guide Appendix D - TracVision M7 Wiring Diagrams Appendix D TracVision M7 Wiring Diagrams This appendix provides receiver wiring diagrams for basic TracVision M7 configurations. Wiring diagrams vary according to the number of receivers installed and the TracVision system configuration (circular/ linear and dual/quad-output).
  • Page 97: Tracvision M7 Wiring Diagram For One Or Two Receivers

    TracVision M5/M7 User’s Guide Appendix D - TracVision M7 Wiring Diagrams TracVision M7 Wiring Diagram for One or Two Receivers Vessel Power Antenna (12 VDC) Data ADCU 60 59 48 47 Yellow Label Red Label DB9 Maintenance Port Green Label...
  • Page 98 TracVision M5/M7 User’s Guide Appendix D - TracVision M7 Wiring Diagrams TracVision M7 Wiring Diagram for Three or Four Receivers (Circular Versions Only)* Vessel Power Antenna (12 VDC) Data ADCU 60 59 48 47 Yellow Label Red Label DB9 Maintenance Port...
  • Page 99: Tracvision M7 Wiring Diagram For Three Or Four Receivers

    TracVision M5/M7 User’s Guide Appendix D - TracVision M7 Wiring Diagrams TracVision M7 Wiring Diagram for Three or Four Receivers (Linear Quad-output Versions Only)* Antenna Vessel Power (12 VDC) Data ADCU 60 59 48 47 Yellow Label Red Label DB9 Maintenance Port...
  • Page 100 TracVision M5/M7 User’s Guide Appendix E - ADCU Wiring Diagrams Appendix E ADCU Wiring Diagrams This appendix provides ADCU wiring diagrams for both required and optional equipment. For installation instructions, refer to the Installation Guide. Contents ADCU Wiring Diagram (Required) ........109...
  • Page 101: Adcu Wiring Diagrams

    TracVision M5/M7 User’s Guide Appendix E - ADCU Wiring Diagrams ADCU Wiring Diagram (Required) Antenna Data Green/White White/Green Blue/White White/Blue Antenna Brown/White White/Brown Orange/White White/Orange Gray/White White/Gray 48 47 60 59 Yellow Label Red Label Green Label Blue Label White Label...
  • Page 102: Adcu Wiring Diagram (Optional Equipment)

    TracVision M5/M7 User’s Guide Appendix E - ADCU Wiring Diagrams ADCU Wiring Diagram (Optional Equipment) 48 47 60 59 Yellow Label Red Label Green Label Blue Label White Label 25 26 13 14 Serial Port #1 Display Power TX1A(+) TX1B(-)
  • Page 103: F Position Grids

    TracVision M5/M7 User’s Guide Appendix F - Position Grids Appendix F Position Grids This appendix contains European and North American position grids for determining your approximate latitude and longitude. Contents European Position Grid ..........113 North American Position Grid ........114...
  • Page 104: European Position Grid

    TracVision M5/M7 User’s Guide Appendix F - Position Grids European Position Grid If you wish to determine your approximate latitude and longitude, use the position grid and table in Figure F-1. Figure F-1 Approximate Latitude and Longitude Grid # Latitude Longitude 7°...
  • Page 105: North American Position Grid

    TracVision M5/M7 User’s Guide Appendix F - Position Grids North American Position Grid If you wish to determine your approximate latitude and longitude, use the position grid and table in Figure F-2. Figure F-2 Approximate Latitude and Longitude Grid #...
  • Page 106 Phone: +1 401 847-3327 Fax: +1 401 849-0045 Phone: +45 45 160 180 Fax: +45 45 160 181 E-mail: info@kvh.com Internet: www.kvh.com E-mail: info@kvh.dk Internet: www.kvh.com © Copyright 2006 KVH Industries Inc. KVH and TracVision are registered trademarks of KVH Industries Inc.

This manual is also suitable for:

Tracvision m7

Table of Contents