Page 2
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. •...
13. NEVER OVERREACH. Keep proper foot- ing and balance at all times. H3390 Wet Tile Saw 14. MAINTAIN TOOLS WITH CARE. Keep 15. DISCONNECT TOOLS before servicing 16. REDUCE THE RISK OF UNINTENTION-...
5. GFCI. Always use a GFCI in the electrical circuit of the saw (Figure 1, Page 6). 6. Water Flow. Ensure that a continuous flow of water is present on both side of the saw blade when cutting. 7. Dry Cutting. Never dry cut with blades designed for wet cutting.
SECTION 2: INTRODUCTION Commentary We are proud to offer the Grizzly Model H3390 Wet Tile Saw. The Model H3390 is part of a growing Grizzly family of fine woodworking machinery. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satis-...
Operating this machine when it is not properly grounded can result in electric shock or electro- cution. H3390 Wet Tile Saw Extension Cord Only use extension cords that are intended for outdoor use. These types of extension cords are designated with a label stating, “Acceptable for...
Site Considerations Floor Load The Model H3390 is a medium load with a medi- um footprint. Most commercial or home shop floors should be sufficient to carry the weight of the machine. Reinforce the floor if you question its ability to support the weight.
Failure to do so could result in injury. -10- The assembly of the Model H3390 Wet Tile Saw is straightforward and can be completed in a rela- tively short period of time. To assemble the saw: Assemble the two stand brackets using (2) M8-1.25 x 50 hex bolts and (2) M8-1.25 lock...
Page 13
Figure 6. Mounting the saw frame to the stand. Slide the plastic water reservoir into one end of the saw frame as shown in Figure 7 . Be sure the reservoir is not protruding from either end of the frame.
Page 14
Attach the blade guard to the motor assem- bly using the M8-1.25 x 30 lock knob and M8 flat washer as shown in Figure 11 . Tile saw blades are sold separately. Blade Guard Figure 11. Attaching the blade guard.
M14 flat washers, and (2) M14 external tooth washers as shown in Figure 16 . Figure 16. Attaching the rail/table assembly to the saw frame. H3390 Wet Tile Saw Blade Changes To change/install a blade: Unplug the machine from the power...
Figure 18. Correct cord positioning. Turn the machine on and make sure your hand is on the power switch in case you need to quickly turn the machine off. The machine should run smoothly with little or no vibration. H3390 Wet Tile Saw...
Figure 19. Filled water reservoir. The pump turns on when the saw is turned on. The water flow can be adjusted using the flow rate lever on the side of the pump. H3390 Wet Tile Saw -15-...
Figure 18, Page 14 . Wear safety glasses and a dust mask. Turn the saw on and allow it to run for one minute. Be sure the blade runs smoothly. If the saw is not operating normally, do not use it.
21 ) and adjusting the table. Cap Screw (1 of 2) Figure 21. Table fine-tuning cap screw. H3390 Wet Tile Saw 45˚ Fence 45˚ beveled edges are cut on tiles using the 45˚ miter fence. Use the cutting groove in the center of the table to support the tile edge ( Figure 22 ) as you slide the tile and table into the saw blade.
-18- Regular periodic maintenance on your Model H3390 will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Check for the following conditions and repair or replace when necessary: 1.
Grizzly Service Department. Trained ser- vice technicians will be glad to help you. If you have any comments regarding this manual, please write to Grizzly at the address below: Grizzly Industrial, Inc. Technical Documentation P.O. Box 2069...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Industrial to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:_________________________________________________...
Page 30
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...
Page 32
Buy Direct and Save with Grizzly Visit Our Website Today And Discover Why • • • – Trusted, Proven and a Great Value! ® Grizzly Is The Industry Leader! ® SECURE ORDERING ORDERS SHIPPED WITHIN 24 HOURS E-MAIL RESPONSE WITHIN ONE HOUR...