Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Grizzly G5979
Summary of Contents for Grizzly G5979
- Page 1 " WOOD LATHE MODEL G5979 INSTRUCTION MANUAL COPYRIGHT © FEBRUARY, 2002 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN CHINA.
- Page 2 WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. •...
-
Page 3: Table Of Contents
1. SAFETY SAFETY RULES FOR ALL TOOLS ...2-3 ADDITIONAL SAFETY INSTRUCTIONS FOR G5979 ...4 2. CIRCUIT REQUIREMENTS 110V OPERATION ...5 GROUNDING ...5 EXTENSION CORDS ...5 3. INTRODUCTION COMMENTARY...6 UNPACKING ...7 PIECE INVENTORY ...8 HARDWARE RECOGNITION ...9 CLEAN UP...10 SITE CONSIDERATIONS ...10 4. -
Page 4: Safety
G5979 Wood Lathe VISITORS... - Page 5 15. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury. G5979 Wood Lathe 16. REDUCE THE RISK OF UNINTENTION- 17. MANY WOODWORKING TOOLS CAN LENGTH 50ft 100ft 18.
-
Page 6: Additional Safety Instructions For G5979
Additional Safety Instructions For The Lathe MAKE SURE ALL GUARDS are in place and that the Lathe sits on a flat, stable sur- face. ALWAYS WEAR EYE PROTECTION or a face shield when operating the Lathe. All safety equipment should be ANSI approved. -
Page 7: Circuit Requirements
Extension Cords If you find it necessary to use an extension cord with the Model G5979, make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in the standard safety instructions to determine the minimum gauge for the extension cord. -
Page 8: Introduction
SECTION 3: INTRODUCTION Commentary We are proud to offer the Grizzly Model G5979 Wood Lathe. The Model G5979 is part of a grow- ing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s com-... -
Page 9: Unpacking
Unpacking The Model G5979 is shipped from the manufac- turer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, immediately call Customer Service for advice. When you are completely satisfied with the con- dition of your shipment, you should inventory its parts in the next section. -
Page 10: Piece Inventory
A full parts list and breakdown can be found toward the end of this manual. For easier assembly, or to identify specific parts, please refer to the detailed illustrations at the end of the manual. Figure 3. Parts layout. NOTICE G5979 Wood Lathe... -
Page 11: Hardware Recognition
Use this chart to match up hardware pieces during the assembly process! Thumb ⁄ Screw ⁄ ⁄ Screw ⁄ ⁄ Setscrew ⁄ Washer 10mm 12mm 16mm G5979 Wood Lathe Lock Countersunk Phillips Phillips Head Head Screw Screw Carriage Bolt Head Bolt Lock Washer ⁄ ⁄... -
Page 12: Clean Up
Most commercial or home shop floors should be sufficient to carry the weight of the Model G5979. If you question the strength of your floor, you can opt to reinforce it. Ensure that the stand or bench you use with the Model G5979 is capable of supporting the machine. -
Page 13: Assembly
Failure to do so could result in injury. Most of your Model G5979 has been assembled at the factory, but some parts must be assembled or installed after delivery. We have organized the assembly process into steps. Please follow along in the order presented here. -
Page 14: Lathe To Stand
-12- Floor Mounting We highly recommend mounting your Model G5979 to the floor. Doing so will eliminate any possibility of the lathe becoming unbalanced and tipping over. The lathe will also produced better results because there will be less vibration from the machine. -
Page 15: Headstock Lock
The spur center is a M.T. #2. To install the spur center: 1. Make certain the spur center is clean and free of dirt or grease. G5979 Wood Lathe 2. Press it into the headstock spindle. Figure 8. Installing the spur center. To remove the spur center: 1. -
Page 16: Faceplate
-14- Extension Bed The extension bed mounts to the left hand side of the main lathe bed. To attach the extension bed: Align the mounting holes of the extension bed and the main lathe bed. Using the M10-1.5 x 25 cap screws and M10 lock washers, attach the extension bed. -
Page 17: Adjustments
5 preset positions. Tighten the lock handle that was loosened in the first step. Do not attempt to lock the headstock into a position other than the 5 presets. G5979 Wood Lathe adjust- loose clothing safety glasses The tailstock can be moved along the length of the lathe bed. -
Page 18: Tool Rest
Re-tighten the lock levers. Make sure there is adequate clearance between the workpiece and the tool rest. Test by hand-turning the workpiece before turning the lathe on. Tool Rest Lock Handles Figure 15. Tool rest assembly. G5979 Wood Lathe... -
Page 19: Operations
R.P.M. The lathe should only be turned ON when the speed is set at the lowest R.P.M. The lathe must be ON to adjust the speed; therefore, be sure to set the speed to the lowest R.P.M. -
Page 20: Spindle Turning
Do not press too firmly or the bearings will bind and overheat. Likewise, do not adjust too loosely or the workpiece will spin off the lathe. Use good judgement. Serious personal injury could result if care is not taken. G5979 Wood Lathe... -
Page 21: Faceplate Turning
Test by hand-turning the work- piece before turning the lathe on. Ensure that the lathe chisel is fully supported by the tool rest. Support the lathe chisel on the tool rest with one hand, while the other hand controls the chisel. See Figure 21. -
Page 22: Maintenance
Damaged V-belt. Any other condition that could hamper the safe operation of this machine. -20- The nonpainted surfaces on the Model G5979 should be protected against rust and pitting. Wiping the machine clean after every use ensures adjust- that wood dust will not trap moisture against bare metal surfaces. -
Page 23: Closure
G5979 Wood Lathe We recommend you keep a copy of our current catalog for complete information regarding Grizzly's warranty and return policy. If you need additional technical information relating to this machine, or if you need general assistance or replacement parts, please contact the Service Department listed in Section 3: Introduction. -
Page 24: Machine Data
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G5979 SWIVEL HEAD WOOD LATHE Design Type ...Bench Model Overall Dimensions: Height ...44'' Length ...60'' Shipping Weight ...190 lbs. Box Size ...54 Footprint ...43... - Page 27 CARRIAGE BOLT M8-1.25 x 10 PW01M FLAT WASHER 8MM PN03M HEX NUT M8-1.25 POWER CORD 110V, LONG W/PLUG PWRCRD110L P5979064 LOGO LABEL 65-1 P5979065-1 GRIZZLY ID/WARNING LABEL P5979066 SPEED LABEL P5979068 SWITCH BOX P5979069 SWITCH FIXING PLATE P5979071 MOTOR POWER WIRE...
-
Page 28: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. -
Page 29: Warranty Card
Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Industrial to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:_________________________________________________... - Page 30 FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here...