Page 2
WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. •...
Page 5
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories. G0562 3 HP Dust Collector 15. USE RECOMMENDED ACCESSORIES. 16. REDUCE THE RISK OF UNINTENTION- LENGTH 17. MANY WOODWORKING TOOLS CAN...
Additional Safety For Dust Collectors 1. THIS DUST COLLECTOR IS TO BE USED FOR WOOD DUST COLLECTION ONLY. Do not use this dust collector to pick up liq- uids and metal scrap including, but not lim- ited to, nails and filings. Metallic debris will contact the spinning impeller and could spark.
We are also pleased to provide this manual with the Model G0562. It was written to guide you through assembly, review safety considerations, and cover general operating procedures. It repre- sents our latest effort to produce the best docu- mentation possible.
SECTION 3: CIRCUIT REQUIREMENTS Amperage Draw The Model G0562 features a single phase 220V 3 HP motor. Amperage Draw 220V ... 18 Amps Circuit Breaker Use the following guidelines when choosing a cir- cuit breaker (circuit breakers rated any higher are...
The outlet must be properly installed and grounded in accor- dance with all local codes and ordinances. G0562 3 HP Dust Collector Circuit Capacity Always check to see if the wires in your circuit are capable of handling the amperage draw from your machine, as well as any other machines that could be operating on the same circuit.
SECTION 4: MACHINE FEATURES Figure 2. Main view of machine features. Canister Filter Cleaning Handle Canister Filter 7" Inlet with Three 4" Ports Clear Collection Bag G0562 3 HP Dust Collector...
Wear safety glasses dur- ing the entire set up process! The Model G0562 is a heavy machine (220 lbs. shipping NOT over-exert yourself while unpacking or mov- ing your machine—get assistance.
Page 12
(e.g. a nut or a washer), we would be glad to replace them, or, for the sake of expedi- ency, replacements can be obtained at your local hardware store. Figure 4. Main box items. Figure 5. Main box items. G0562 3 HP Dust Collector...
-12- Site Considerations Floor Load The Model G0562 weighs 209 lbs and has a base footprint of 32" x 57 ⁄ ". Most commercial floors are suitable for the machine. Some residential floors may require additional reinforcement to support both the machine and operator.
"-18 x ⁄ "...16 Tools Needed: Wrench or Socket 12mm...1 To assemble the dust collector base: Place the base upside down. Secure the casters into the mounting brack- ets under the base with the flange bolts (Figure 7). Figure 7. Caster installed on mounting bracket.
Place the canister support over the holes on the base edge (Figure 11). Figure 11. Canister support attached to base. Secure the canister support in place with 2 flange bolts. Repeat steps 1 & 2 for the second brace. ⁄ "...4 G0562 3 HP Dust Collector...
Attach the canister support to the side of the collector ring with the 2 remaining flange bolts. Repeat steps 1-3 for the other collector ring (Figure 13). G0562 3 HP Dust Collector Figure 13. Collector rings installed. Canister Filter Components and Hardware Needed: Canister Filters ...2 Canister Filter Cleaning Handles ...2...
Secure the narrow foam strip around the out- side bottom rim of the collector ring and trim the excess. Hook the clear collection bag on the hooks around the bottom of the collector. (Figure 18). G0562 3 HP Dust Collector...
Tighten the belt clamp around the narrow foam strip to seal and secure the lower col- lection bag (Figure 20). Figure 20. Lower collection bag installed. G0562 3 HP Dust Collector Inlet Components and Hardware Needed: 7" Inlet w/Three 4" Ports ...1...
SECTION 6: COLLECTION SYSTEM General The Model G0562 can be operated as either a stationary or a mobile unit. There are advantages and disadvantages to both set-ups. The advan- tage of the mobile system is eliminating the cost of many ducts and fittings. On the other hand, the stationary system is more versatile and conve- nient.
However, the cost of specifically designed flexible duct can vary greatly. Grizzly offers polyethylene hose which is well suited for the removal of particulate matter, especially saw- dust, since it is durable and completely flexible.
Page 22
23. Ensure that each machine is continuously grounded to the grounding terminal in your elec- tric service panel. Plastic Blast Gate Flex-Hose Metal Duct Internal Ground Wire Figure 23. Flex-hose grounded to machine. Ground Screw External Ground Wire G0562 3 HP Dust Collector...
The best way to plan your new system is to draw a bird’s eye view (as shown in Figure 24) of your shop and sketch the following: Your desired location of the dust collector, usually in a corner or along a wall. The location of each machine in the system.
If you cannot easily locate the source of an unusual noise or vibration, contact our service department for help. loose clothing Operating your Model G0562 is simple and safety glasses straightforward. Blast gates located at each of the machines controls the air flow from the wood- working machine to the dust collector.
This microscopic airborne dust is extremely unhealthy to breathe and can cause serious health problems. Grizzly offers replacement collection bags and canister filters for your Model G0562 Dust Collector. Model H5783 Replacement Canister Filter Model H6899 Replacement Collection Bag...
When the collection bag is full, unclamp the collection bag and dispose of the dust. Install a new collection bag. While the Model G0562 excels at collecting the majority of wood dust produced by your machines, it is not an air filter; therefore, we...
Grizzly Service Department. Trained ser- vice technicians will be glad to help you. If you have any comments regarding this manual, please write to Grizzly at the address below: Grizzly Industrial, Inc. Technical Documentation P.O. Box 2069...
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MODEL G0562 3 HP DUST COLLECTOR Design Type ...Single Stage Floor Model Overall Dimensions: Base ...21 Height ...78" Shipping Weight ...220 lbs. Net Weight ...187 lbs.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Industrial to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:__________________________________________________...
Page 34
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...
Page 36
Buy Direct and Save with Grizzly Visit Our Website Today And Discover Why • • • ® – Trusted, Proven and a Great Value! Grizzly ® Is The Industry Leader! SECURE ORDERING ORDERS SHIPPED WITHIN 24 HOURS E-MAIL RESPONSE WITHIN ONE HOUR...