Related Manuals for Speco EZVR8
Summary of Contents for Speco EZVR8
- Page 1 EZVR8 User’s Manual Speco Technologies 200 New Highway Amityville, NY 11701 800-645-5516 www.specotech.com...
-
Page 2: Safety Precautions
Safety Precautions CAUTION RISK OF ELECTRICAL SHOCK. DO NOT OPEN ! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of insulated dangerous Voltage within the product’s enclosure that may be of sufficient magnitude to constitute risk of electrical shock to persons. -
Page 3: About This Document
2. Several chips on the main board of the unit and hard disk drive inside the unit generate heat which must be properly discharged. Do not place any objects adjacent to the ventilation openings on the sides of the unit. 3. Put the EZVR8 in a well-ventilated place and do not put heat-generating objects on the unit. - Page 4 FCC Statement: WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received including interference that may cause undesired operation."...
-
Page 5: Installation
6. Connect your monitor cable to the BNC connectors on the rear. connector labeled “Monitor” on the rear. 7. Connect the power adaptor. 8. Turn on the “Power” switch after the cameras are installed. The EZVR8 will then “boot” up and begin recording. -
Page 6: Front Panel
FRONT PANEL : Split screen mode button : Channel 1 full screen button CHANNEL 1 : Channel 2 full screen button CHANNEL 2 : Channel 3 full screen button CHANNEL 3 : Channel 4 full screen button CHANNEL 4 : Channel 5 full screen button CHANNEL 5 : Channel 6 full screen button CHANNEL 6... -
Page 7: Rear Panel
REAR PANEL Power cord in 12VDC / 5A, Power Switch (ON / OFF) Camera 1 ~ 8 input BNC type Main monitor output Audio channel input x 1 and output x 1 – RCA Type Alarm / Relay connector / RS485... - Page 8 Booting Up Detecting the hard disk Live screen Indicator : Live: HDD installed Recording Overwrite Live mode Video loss Key lock Alarm Input Alarm Output Playback: Forward Reverse Pause...
- Page 9 Remote controller The keys on the remote control have the same functions as the front keyboard of the unit.
- Page 10 Main MENU – Time Setup Press ENTER to select Time Set. Press ENTER again to display the cursor. Use the left or right buttons to select the item you wish to adjust, then press ENTER to change the value. Press MENU to return to the previous screen and move the cursor to Apply. Press ENTER to confirm.
- Page 11 Main MENU – Audio Record Use direction buttons to select Audio Record. Press ENTER to select On or Off. Diagram Speaker RCA Cable Audio Out (Line Level) Microphone Audio In (Line Level)
- Page 12 Main MENU – Alarm Input Use direction buttons to select Alarm Input. Press the Enter button to choose the type of sensor input (Normally Open - NO or Normally Closed - NC). To disable the alarm mode switch to the Off position..
- Page 13 Alarm Input Door closed Door open The Alarm Signal type depends upon the Alarm Sensor polarity defined as NO (Normal Open) or NC (Normal Close). Alarm Output: Relay: NO + COM or NC + COM Relay: NO (Normal open) Alarm trigger Relay: NC (Normal Close)
- Page 14 Main MENU – Auto Record Use direction buttons to select Auto Record. When Auto Record is set to On, the EZVR8 Press the Enter button to choose On or Off. will start recording again after 2 minutes of If switched to OFF then Auto Record is inactivity after being manually stopped.
- Page 15 Main MENU – Status Bar If set ON, the status bar will show date-time Use direction buttons to select Status Bar . and status icons . Then press ENTER to select ON or Off . If set Off the status bar will hide date-time and status icons .
- Page 16 Main MENU – Exit Use direction buttons to select Exit. Press Enter button to leave the menu. Playback mode – Note: Instructions appear on the screen after selecting “Search” Press SEARCH to enter the playback mode. Press ENTER to select a date and time. Use the left or right arrows to select the item Press MENU to return to the previous screen you wish to change, then press ENTER to...
- Page 17 Press ENTER to start the searching. Wait until the unit starts to playback. Backup mode Note: Plug in a USB device before starting the backup You must first playback an event using When the event you wish to backup appears instructions from the previous page.
- Page 18 Player Software Main Screen Click icon to select the file to play. It will be in .vvf format...
- Page 19 Starts to play; 2 3 4 5 6 9 10 11 12 13 Open File Fast Forward Fast Reverse Capture (Save to C:\ Capture & Clipboard) Play Reverse Full Screen mode Previous Frame Quad Screen mode Pause Split Screen mode Next Frame Export to AVI format Play...
- Page 20 Specifications EZVR8 Model Input 8 CH Inputs 1.0Vp-p, 75ohm (BNC Type) Output Main monitor composite video (BNC type) x 1 Horizontal Resolution 640x480 (NTSC) / 640x544 (PAL) S/N Ratio More than 40dB Color 6.7 Million Monitoring Method Channel Display 1 / 4 / 8 channels display 640(H) x 480(V) Active Pixels(NTSC);...