Page 1
AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 The information included in this Splendide Repair Manual may change without notice. Please see our web site Pages: www.splendide.com/service/docs.html for updates, corrections or additions.
Page 2
Repair Manual. If you have any questions regarding the proper diagnosis, repair or operation of any Splendide Appliance, please contact Splendide Division Westland Sales at 1-800-356-0766.
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 TABLE OF CONTENTS Page 1. Model & Serial Number Locations ....................1 2. Top Panel ............................2 3. Control Panel..........................3 4. Control Panel Components......................4 5.
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 1. MODEL & SERIAL NUMBER LOCATION Fig. 1-1 Fig. 1-2 • The Model and Serial Number Tag is located on the front of the Appliance behind the door (Fig. 1-1). The Model shown is an AWD120 with a Serial Number of 403043152 (Fig.
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 2. TOP PANEL Fig. 2-1 Fig. 2-2 • To remove the Top Panel, first remove the two (2) Phillips screws located at the rear corners of the panel (Fig. 2-1). With the two screws removed lift the rear of the panel up approximately three (3) inches and then slide the panel back, moving it away from the Control Panel (Fig.
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 3. CONTROL PANEL Fig. 3-1 • To remove the Control Panel, first remove the two Phillips screws located on the top corners of the Control Panel (Fig 3-1).
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 4. CONTROL PANEL COMPONENTS - Switches and Potentiometers Fig. 4-2 Fig. 4-1 • The Control Panel has three main controls; Push Buttons (A), Knobs (B) and the Program Dial (C).
Page 8
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 4. CONTROL PANEL COMPONENTS - Program Selector Fig. 4-7 Fig. 4-8 Fig. 4-6 • To remove the Program Selector, first remove the Program Selector Knob by grasping it firmly and pulling it toward you (Fig. 4-6).
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 5. TOE KICK & DRAIN MOTOR Fig. 5-2 Fig. 5-1 • To remove the Toe Kick, carefully insert a small screwdriver into each of the three (3) retention clips pushing each clip down and then moving to the next clip (Fig.
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 6. DRUM BOOT Fig. 6-1 Fig. 6-2 Fig. 6-3 • To remove the Drum Boot (Fig. 6-1) start by removing the Door Boot Spring (Fig. 6-2). The Door Boot Spring is located just under the front lip of the Drum Boot.
AW 120 / AW 122 / AW 125 REPAIR MANUAL AWD 120 / AWD 121 / AWD 129 7. DOOR SWITCH • To remove the Door Switch, remove the two (2) T-15 Torx screws (Fig. 7-1). Then remove the Top Panel as described in Section 2. With the Top Panel removed disconnect the wire harness from the Door Switch and replace (Fig.
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 9. HEATER ASSEMBLY (AWD 120 Only) INDIVIDUAL COMPONENTS: A. Blower Motor B. Heater, 120v / 1200w C. High Limit Thermostats 340˚f, non-resetable D.
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 10. PRESSURE SWITCH • To remove the Pressure Switch, first remove the Top Panel as described in Section 2, then push in on the center support of the Pressure Switch Bracket and slide the Pressure Switch up and off (Fig.
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 12. CONTROL BOARD • To remove the Control Board, remove the two (2) T-15 Torx screws located at the rear right corner of the unit.
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 13. MAIN MOTOR Fig. 13-1 • To remove the Main Motor, first remove the Drive Belt and then the two (2) 13 mm Motor Mounting Plate Bolts (Fig. 13-1). The Main Motor has three support points, two in the front (A) and a third located on a Rear Mounting Bracket that supports the Motor on the rear left side (Fig.
REPAIR MANUAL AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 14. FAULT CODES A repair fault is signaled by the continuous rotating of the Program Knob and the flashing of the Door Locked LED. The Fault Code is determined by counting the sequence of individual flashes of the LED (2 flashes = F2).