Related Manuals for Zenoah PSJ2310
Summary of Contents for Zenoah PSJ2310
- Page 1 115 50 14 73 (209) OWNER’S MANUAL POLE SAW PSJ2310 01-PSJ2310_GB_209＿三.indd 1 12.9.12 1:09:20 PM...
-
Page 2: Table Of Contents
PSJ2310 Contents SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into 1. Parts location ...........2 consideration to prevent possible serious bodily injury, and for 2. Specifications ...........3 this reason you are requested to read all such instructions care- 3. -
Page 3: Specifications
Dry weight ..........10”: 5.9kg Size ........10 (25) in.(cm) Engine Type ....Air-cooled 2-stroke gasoline Saw chain Type ....10”: OREGON 25AP-58E Model ........ Zenoah G23LS Pich x Gauge ..1/4x0.050 (6.35x1.3) in.(mm) Displacement ......22.5cm Sprocket ..............8T Fuel ..............Mixture Oil pump ..........Plunger type... -
Page 4: For Safe Operation
PSJ2310 5. For safe operation WORKING PLAN 1. Read this manual carefully until you 1. You should never use the product completely understand and follow all when under the influence of alcohol, safety and operating instructions. when suffering from exhaustion or lack 2. - Page 5 Cut only materials recommended by the placing the oil or any lubricant, always be sure to use only ZENOAH prod- manufacturer. And use only for tasks explained in the manual. ucts or products which have been certified by ZENOAH for use with 1.
- Page 6 PSJ2310 5. For safe operation HANDLING FUEL must take several steps to keep your 1. The engine of the ZENOAH product jobs free from accident or injury: is designed to run on a mixed fuel, which contains highly flammable 1. Understand kickback and pinching! gasoline.
-
Page 7: Set Up
PSJ2310 6. Set up MOUNTING ENGINE JOINT ATTACHMENT (1) Knob bolt 1. Push the shaft tube toward the clutch housing and • Insert the attachment to the main shaft. rotate it by hand to check that the power transmission • Tighten the knob bolt securely. shaft is engaged with the gears. - Page 8 PSJ2310 6. Set up 4. Adjust the chain tension by turning the chain tension HARNESS adjust screw until the saw chain does not sag from the underside of the bar. WARNING ALWAYS WEAR THE PROVIDED HARNESS WHEN USING THE MACHINE! Always make sure the machine is hooked securely to the harness.
-
Page 9: Fuel And Chain Oil
2. Put fuel into the fuel tank to 80% of the full capacity. 3. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. • The Zenoah engines are lubricated by oil specially WARNING formulated for air-cooled 2-cycle gasoline engine use. -
Page 10: Operation
PSJ2310 8. Operation 6. While holding the unit firmly, pull out the starter rope STARTING ENGINE quickly until engine fires. WARNING The cutting head will start rotating upon the engine starts. 1. Feed fuel and chain oil into their respective tanks and tighten the caps securely. - Page 11 PSJ2310 8. Operation (a) Clockwise-oil flow increase NOTE (b) Counter clockwise-oil flow decrease The oil reservoir has a capacity sufficient to provide (c) Middle about 40 minutes of cutting time (when set to deliver ADJUSTING THROTTLE CABLE the minimum flow rate, or about as long as you’ll get • The normal play is 1 or 2mm when measured at the...
-
Page 12: Maintenance
PSJ2310 9. Maintenance Every Every Every Before System/components Procedure Note hours hours hours after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean replace, if necessary ✔ ✔ see ADJUSTING IDLING replace carburetor idle adjusting screw ✔... - Page 13 PSJ2310 9. Maintenance INTAKE AIR COOLING VENT PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, WARNING and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and •...
- Page 14 PSJ2310 9. Maintenance OILING PORT DRIVE SPROCKET Dismount the guide bar and check the oiling port for Regularly check the degree of wear on the drive clogging. sprocket. Replace if wear is excessive. (1) Oiling port GUIDE BAR Remove sawdust in the guide bar groove and the oiling (1) Drive Sprocket port.
-
Page 15: Storage
PSJ2310 9. Maintenance After every cutter has been set, check the depth gauge SAW CHAIN and file it to the proper level as illustrated. WARNING It is very important for smooth and safe operation to keep the cutters always sharp. -
Page 16: Troubleshooting Guide
→ consult with the repair specialty store cylinder fin, fan cover When your unit seems to need further service, please consult with our ZENOAH service shop in your area. Limited warranty Should any failure occur on the product under normal...