Toshiba TECRA M5 User Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. TECRA M5
  6. User manual

Toshiba TECRA M5 User Manual

Hide thumbs Also See for TECRA M5:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Maintenance Manual, User Manual
User's Manual
TECRA M5

Advertisement

Table of Contents
loading

Related Manuals for Toshiba TECRA M5

Summary of Contents for Toshiba TECRA M5

  • Page 1 User’s Manual TECRA M5...
  • Page 2 Disclaimer This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TECRA M5 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice.
  • Page 3 EU Declaration of Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.
  • Page 4 Following information is only for EU-member states: The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

  • Page 5: Table Of Contents

    Table of Contents Preface General Precautions Introduction Chapter 1 Equipment checklist........1-1 Features.
  • Page 6 Replacing the battery pack ....... . .6-15 TOSHIBA Password Utility ....... . .6-16 Power-up modes .
  • Page 7 TOSHIBA support ........
  • Page 8 Regulatory statements........D-3 Using Bluetooth™ Card from TOSHIBA equipment in Japan ..D-6...

  • Page 9: Preface

    This manual tells how to set up and begin using your TECRA M5 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
  • Page 10 Preface Chapter 7, Setup, explains how to configure the computer using the HW Setup program and TPM. Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, provides helpful information on how to perform some diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly.
  • Page 11 Preface Display Names of windows or icons or text generated by the computer that appear on its display screen are presented in the type face you see to the left. Messages Messages are used in this manual to bring important information to your attention.
  • Page 12 Preface User’s Manual...

  • Page 13: General Precautions

    General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
  • Page 14 General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phones Use of mobile phones can interfere with the audio system.

  • Page 15: Equipment Checklist

    Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
  • Page 16 ® Windows XP Professional ■ Microsoft Internet Explorer ■ TOSHIBA Utilities ■ TOSHIBA Wireless Key Logon ■ TOSHIBA SD Memory Boot Utility ■ DVD Video Player ■ TOSHIBA Dual Pointing Device utility ■ TOSHIBA Power Saver ■ TOSHIBA Mobile Extension ■...

  • Page 17: Features

    If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and...
  • Page 18 Introduction Memory Slots 512, 1,024, or 2,048 MB memory modules can be installed in the two memory slots for a maximum of 4,096 MB system memory. Video RAM Part of system memory is used for Video RAM. Up to 128 MB of RAM is provided for video display.

  • Page 19: Optical Disk Drive

    Introduction Disks Hard disk drive Available in five sizes. (HDD) ■ 40.0 billion bytes (37.26 GB) ■ 60.0 billion bytes (55.89 GB) ■ 80.0 billion bytes (74.53 GB) ■ 100.0 billion bytes (93.16 GB) ■ 120.0 billion bytes (111.79 GB) Part of the space on the hard disk drive is reserved as administration space.
  • Page 20 Introduction DVD Super Multi Some models are equipped with a full-size DVD drive Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.

  • Page 21: Toshiba Dual Pointing Device

    Refer to Chapter 5, Keyboard, for details. TOSHIBA Dual Pointing Device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer and scrolling of windows.
  • Page 22 Introduction SD card This slot lets you easily transfer data from devices, such as digital cameras and Personal Digital Assistants that use SD card flash-memory. Refer to Chapter 8, Optional Devices. Multimedia Sound system A Windows sound system compatible sound system provides internal speakers and a microphone as well as supports jacks for an external microphone and headphones.
  • Page 23 Slim Select Bay is a single-drive bay that accommodates a DVD-ROM&CD-R/RW drive, DVD Super Multi drive, secondary hard disk drive and 2nd battery. The TOSHIBA Mobile Extension enables hot insertion of modules when you are using a plug and play operating system.

  • Page 24: Special Features

    Select Bay lock screw is inserted in the unlock position when purchased. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Assist Press this button to launch an application button automatically.
  • Page 25 LCD display panel is opened. You can specify the setting in the When I close the lid item of the Setup Actions tab in TOSHIBA Power Saver. Low battery When battery power is exhausted to the point that...

  • Page 26: Utilities

    To start the utility, To access this utility, click start, click Control Panel, click Printers and Other Hardware and click the TOSHIBA HWSetup icon. 1-12 User’s Manual...
  • Page 27 TOSHIBA Presentation button (default setting is the simultaneous display on LCD and CRT with resolution of 1024 × 768) and to the TOSHIBA Assist button (default setting is the TOSHIBA Assist). To access this utility, click start, point to Control Panel, choose Printers and Other Hardware and click the Toshiba Controls icon.
  • Page 28 Advanced Port Repricator III Plus. To open the property dialog, select TOSHIBA Mobile Extension from TOSHIBA Assist. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also...
  • Page 29 Device with Fn + F9 keys. To customize the functions of TOSHIBA Dual Pointing Device easily. TOSHIBA Mic Effect TOSHIBA Mic Effect is a utility used to enable comfortable calls with echo cancellation function. The echo cancellation function removes or reduces any harsh echoes or howling sounds that occur when playing audio sounds recorded with a microphone through the speakers.

  • Page 30: Options

    A 512, 1,024, or 2,048 MB memory module can easily be installed in the computer. Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. Extended capacity An additional battery pack can be purchased battery pack from your TOSHIBA dealer.

  • Page 31: Slim Select Bay Options

    Introduction Advanced Port The Advanced Port Replicator III Plus provides Replicator III Plus the ports available on the computer in addition to separate PS/2 mouse and PS/2 keyboard ports, a digital visual interface (DVI) port, i.LINK™ (IEEE1394) port, line-in jack and line-out jack, External monitor port, Universal Serial Bus port (USB2.0) ×...
  • Page 32 Introduction 1-18 User’s Manual...

  • Page 33: Chapter 2 The Grand Tour

    Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Legal Footnote (Non-applicable Icons) For more information on the Legal Footnote regarding Non-applicable Icons, please refer to the Legal Footnotes section in Chapter 10. Front with the display closed The following figure shows the computer’s front with its LCD display panel in the closed position.

  • Page 34: Left Side

    The Grand Tour ■ Turn WiFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any WiFi or Bluetooth functionality.
  • Page 35 The Grand Tour Do not block the cooling vents. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury.

  • Page 36: Right Side

    The Grand Tour Right side The following figure shows the computer’s right side. Volume control Microphone jack Slim Select Bay Headphone jack USB ports Serial port The right side of the computer Volume control Use this dial to adjust the volume of the stereo speakers and the stereo headphones.

  • Page 37: Back Side

    The Grand Tour Back side The following figure shows the computer’s back side. LAN active indicator Link indicator (green) (orange) Modem jack DC IN 15V jack Video-out jack LAN jack The back side of the computer Video-out jack Plug an S-Video cable into this jack for video-out. The S-Video cable carries video signal.

  • Page 38: Underside

    The Grand Tour LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T).
  • Page 39 The Grand Tour Battery lock Slide the battery lock to release the battery pack for removal. Battery pack The battery pack powers the computer when the AC adaptor is not connected. For detailed information on the battery pack, refer to Chapter 6, Power and Power-Up Modes.

  • Page 40: Front With The Display Open

    (Not shown) Touch Pad Stereo speaker (Left) Fingerprint Sensor Power button TOSHIBA Assist button Touch Pad AccuPoint control button TOSHIBA Presentation button control buttons The front of the computer with the LCD panel open Display hinge The display hinge holds the LCD display panel at easy-to-view angles.
  • Page 41 The Grand Tour Fingerprint Sensor Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ■ Logon to Windows and access a security-enabled homepage through IE (Internet Explorer). ■ Files and folders can be encrypted/decrypted and third party access to them prevented.
  • Page 42 This setting is supported in Windows XP only. Press this button again to change back to single display mode on the internal LCD. You can specify the function of the TOSHIBA Presentation button in the TOSHIBA Controls properties. TOSHIBA Assist Press this button to launch a program.

  • Page 43: System Indicators

    The Grand Tour System indicators LEDs beneath icons, light when various computer operations are in progress. System indicators SD card The SD card indicator glows green when the computer is accessing the SD card slot. DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor.

  • Page 44: Keyboard Indicators

    The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers.

  • Page 45: Usb Floppy Disk Drive (Optional)

    The Grand Tour USB floppy disk drive (optional) The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. USB connector Disk-In-Use Indicator Floppy disk slot Eject button USB floppy disk drive USB connector Insert this connector into one of the USB ports of your computer.

  • Page 46: Optical Disk Drives

    The Grand Tour Optical disk drives One of the following Optical disk drives is installed in the computer: DVD- ROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.

  • Page 47: Dvd Super Multi Drive

    The Grand Tour Formats The drives support the following formats: ■ ■ CD-ROM DVD -Video ■ ■ DVD-ROM CD-Text ■ ■ CD-DA CD-ROM Mode 1, Mode 2 ■ ■ Photo CD Enhanced CD (CD-EXTRA) ™ (single/multi-session) ■ Addressing Method 2 ■...

  • Page 48: Ac Adaptor

    For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region. Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC.

  • Page 49: Chapter 3 Getting Started

    Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read the Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.

  • Page 50: General Conditions

    PC, it could cause a system failure, malfunction or loss of data. If dust contaminates the PC, do not turn on the power. Take it to an authorized Toshiba service provider before you use it. ■ Never place your PC near an object that generates a magnetic field, such as a speaker or TV.

  • Page 51: Placement Of The Computer

    Getting Started ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location.

  • Page 52: Seating And Posture

    Getting Started Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level 90°angles Foot rest Posture and positioning of the computer ■...

  • Page 53: Work Habits

    Getting Started Lighting Select the right level of illumination and place your PC appropriately to minimize glare from overhead lights, desk lamps and windows. Glare on the LCD or monitor may cause eye strain, eye fatigue or headaches. Consider the following suggestions regarding lighting your work environment: ■...

  • Page 54: Connecting The Ac Adaptor

    Power and Power-Up Modes. ■ Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury.
  • Page 55 Getting Started ■ Never plug the AC adaptor or Battery Charger into a power source that does not correspond to both the voltage and the frequency specified on the regulatory label of the unit. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.

  • Page 56: Opening The Display

    Getting Started Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled. 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. DC IN 15V jack AC adaptor’s DC output plug Connecting the adaptor to the computer...

  • Page 57: Turning On The Power

    Getting Started Turning on the power This section describes how to turn on the power. The Power button LED indicates the status. Refer to the Power indicators section in Chapter 6, Power and Power-Up Modes. ■ After you turn on the power for the first time, do not turn it off until you have set up the operating system.

  • Page 58: Turning Off The Power

    ■ When the AC adaptor is connected, the computer will go into Standby Mode according to the settings in the TOSHIBA Power Saver utility. ■ To restore operation from Standby Mode, press the power button or press any key. The latter action only works on the internal keyboard if the Wake-up on Keyboard option is enabled in HW Setup.
  • Page 59 1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Actions tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.

  • Page 60: Hibernation Mode

    For the computer to shut down in Hibernation Mode, this feature must be enabled in two places: the Hibernate tab in Power Options and Setup Actions tab in TOSHIBA Power Saver. If you do not configure this feature, the computer will shut down in Standby Mode - if battery power becomes depleted, data saved in Standby Mode will be lost.

  • Page 61: Restarting The Computer

    3. Select the Hibernate window in the Power Options Properties, select the Enable hibernation check box and click the Apply button. 4. Open TOSHIBA Power Saver. 5. Select the Setup Action window. 6. Enable the desired Hibernation settings for When I press the power button and When I close the lid.

  • Page 62: Restoring The Preinstalled Software

    Restoring TOSHIBA utilities and drivers If Windows is working properly, individual drivers or applications can be separately restored. The TOSHIBA Tools & Utilities folder (C:\TOOLSCD) contains drivers and applications, which are included with your computer system. If your system drivers or applications have become damaged in some way, you can reinstall most of the components from this folder.

  • Page 63: Chapter 4 Operating Basics

    This chapter describes the basic operations of your computer and precautions when using it, as well as the handling of CD/DVD. TOSHIBA Dual Pointing Device The computer is equipped with a dual point system: a Touch Pad and an AccuPoint pointing stick.

  • Page 64: Using The Accupoint

    Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material.

  • Page 65: Using The Fingerprint Sensor

    Operating Basics 2. Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg. Using the Fingerprint Sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints.

  • Page 66: How To Delete The Fingerprint Data

    Operating Basics ■ Avoid the following finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate ■ Soaked or swollen finger (e.g. after taking bath) ■ Injured finger ■...

  • Page 67: Points To Note About The Fingerprint Utility

    Toshiba does not guarantee that the fingerprint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.

  • Page 68: Set Up Procedure

    Operating Basics Set Up Procedure Please use the following procedure when first using fingerprint authentication. Fingerprint Registration Enroll the required authentication data using the “User Enrollment” Wizard. ■ The fingerprint authentication uses the same Windows logon ID and password. If the Windows logon password has not been setup, please do so before registration.

  • Page 69: Window Logon Via Fingerprint Authentication

    ■ It is necessary to register the User Password before using the Fingerprint Power-on Security and its extended function, the Fingerprint Single Sign-on Feature. Please use TOSHIBA Password Utility to register the User Password. ■ If you fail fingerprint authentication more than five times, you must enter the User Password or Supervisor Password manually to start the computer.

  • Page 70: How To Enable Fingerprint Power-On Security Settings

    User/BIOS Password and Windows Logon password before using the Fingerprint Power-on Security and this Fingerprint Single Sign-on Feature. Please use TOSHIBA Password Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon password.

  • Page 71: Fingerprint Utility Limitations

    TOSHIBA does not guarantee that the Fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.

  • Page 72: Using The Usb Floppy Disk Drive (Optional)

    Operating Basics Using the USB floppy disk drive (optional) The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. Refer to Chapter 2, The Grand Tour, for more information. Connecting the USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port.

  • Page 73: Changing Slim Select Bay Modules

    DVD Super Multi drive, HDD adaptor and 2nd battery pack. To avoid injury, do not put your hand into the Slim Select Bay slot. The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1,...

  • Page 74: Using Optical Disk Drives

    Operating Basics Inserting a module Insert the Slim Select Bay HDD adaptor as described below. 1. Insert the Slim Select Bay HDD adaptor in the computer as shown below and press until the ejector clicks. 2. If you want to lock the Slim Select Bay HDD adaptor, set the Slim Select Bay lock screw in the hole for the lock position.

  • Page 75: Loading Discs

    Operating Basics Loading discs To load CD/DVDs, follow the steps below. 1. When the computer’s power is on, press the eject button to open the disc tray slightly. Eject button Pressing the eject button 2. Grasp the disc tray gently and pull until it is fully opened. Disc tray Pulling the disc tray open 3.

  • Page 76: Removing Discs

    Operating Basics When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat.
  • Page 77 Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can hold it. Hold the CD/DVD gently and lift it out. Removing a CD/DVD 3. Push the center of the disc tray to close it. Press gently until it locks into place.

  • Page 78: Writing Cds On Dvd-Rom&Cd-R/Rw Drive

    RICOH Co., Ltd. Ultra-Speed CD-RW: MITSUBISHI CHEMICAL CORPORATION TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.

  • Page 79: When Writing Or Rewriting

    Operating Basics ■ Do not run software such as a screen saver which can put a heavy load on the CPU. ■ Operate the computer at full power. Do not use power-saving features. ■ Do not write while a virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background.

  • Page 80: Writing Cd/Dvds On Dvd Super Multi Drive

    Legal Footnotes TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/-RAM disc that may be caused by writing or rewriting with this product.

  • Page 81: Before Writing Or Rewriting

    Based on TOSHIBA’s limited compatibility testing, we suggest the following manufacturers of CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/ +RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
  • Page 82 Operating Basics DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Hitachi Maxell Ltd. This drive cannot use discs that allow writing faster than 8 speed (DVD-R, DVD+R), 4 speed (DVD-RW, DVD+RW), 5 speed (DVD-RAM), 2 speed (DVD-R DL) and 2.4 speed (DVD+R DL).
  • Page 83 Operating Basics ■ Be sure to close all other software programs except the writing software. ■ Do not run software such as a screen saver, which can put a heavy load on the CPU. ■ Operate the computer in the full-power mode. Do not use power-saving features.
  • Page 84 Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste. The original data will be lost if there is a write error. Discs created in DVD-R DL (Layer Jump Recording) cannot be read. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■...

  • Page 85: Data Verification

    3. Mark the Verify data written to the disc after burning check box in the Data Options. Click the OK button. DLA for TOSHIBA Note the following limitations when you use DLA: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW).

  • Page 86: How To Learn More About Intervideo Windvd Creator

    Operating Basics 4. Click the Advanced tab in the System Properties window. 5. Click the Settings icon in the “Performance” section. 6. Click the Advanced tab in the Performance Options window. 7. Click the Change icon in the “virtual memory” section. 8.
  • Page 87 2. Before recording the video to DVD ■ When you record to DVD discs, please use only media recommended by TOSHIBA. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write the DVD.

  • Page 88: Media Care

    Operating Basics 3. About Disc Manager ■ WinDVD Creator can edit one play list on a disc. ■ WinDVD Creator might show a different thumbnail than you previously set in CE (Consumer Electronics) DVD-RAM recorder. ■ Using the Disc Manager, you can edit DVD-VR format on DVD-RAM, DVD+VR format on DVD+RW, and DVD-Video format on DVD-RW.

  • Page 89: Sound System

    Operating Basics 3. Always handle floppy disks with care, to prevent the loss of stored data. Always apply the floppy disk label in the correct location. Never apply a new label on top of an existing one. The label could come loose and damage the floppy drive.

  • Page 90: Sigmatel Control Panel

    Adjust the equalizer settings to enhance sound quality. TOSHIBA Mic Effect TOSHIBA Mic Effect is a utility used to enable comfortable calls with echo cancellation function. The echo cancellation function removes or reduces any harsh echoes or howling sounds that occur when playing audio sounds recorded with a microphone through the speakers.

  • Page 91: Modem

    Check the specified areas carefully before using it. To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.

  • Page 92: Properties Menu

    Operating Basics Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system.
  • Page 93 Operating Basics ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■...

  • Page 94: Wireless Communications

    Operating Basics Disconnecting To disconnect the internal modular cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer’s modem jack in the same manner.

  • Page 95: Bluetooth Wireless Technology

    ■ TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof. Bluetooth wireless technology Some models in this series are equipped with Bluetooth™...

  • Page 96: Product Support

    ® 1. Install: ® On Windows2000 or Windows XP, Bluetooth™ Stack for Windows TOSHIBA does not have a digital signature. 2. Fax application software: Regarding FAX application software, there are some software that you cannot use on this Bluetooth™ Stack.

  • Page 97: Lan

    Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction. Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.

  • Page 98: Connecting Lan Cable

    Operating Basics Connecting LAN cable To connect a LAN cable, follow the steps below. ■ Connect the AC adaptor before connecting a LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.

  • Page 99: Cleaning The Computer

    Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.

  • Page 100: Using The Hard Disk Drive (Hdd) Protection

    Operating Basics Using the Hard Disk Drive (HDD) Protection This computer has a function for reducing the risk of damage on hard disk drive. Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks, and other such occurrences in the computer, and automatically moves the HDD (Hard Disk Drive) head to the safe position to reduce the risk of damage that could be caused to the disk by head-to-disk contact.

  • Page 101: Toshiba Hdd Protection Properties

    Operating Basics TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start, point to All Programs, point to TOSHIBA, point to Utilities and click HDD Protection setting.

  • Page 102: Heat Dispersal

    Operating Basics Details To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Details Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.

  • Page 103: Chapter 5 The Keyboard

    Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.

  • Page 104: Function Keys: F1

    Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.

  • Page 105: Hot Keys

    The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay section in this chapter for more information on how to operate these keys.
  • Page 106 F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver. Standby: When you press Fn + F3, the computer enters the Standby Mode.
  • Page 107 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. ■ The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.

  • Page 108: Fn Sticky Key

    Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.

  • Page 109: Windows Special Keys

    The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.

  • Page 110: Numeric Mode

    The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in the figure below. Press Fn + F11 again to turn off the overlay. The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard...

  • Page 111: Generating Ascii Characters

    The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation.
  • Page 112 The Keyboard 5-10 User’s Manual...

  • Page 113: Chapter 6 Power And Power-Up Modes

    Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a...
  • Page 114 Power and Power-Up Modes Power conditions continued Power on Power off (no operation) 2nd battery fully • Operates • No charge adaptor charged • No charge • LED: 2nd Battery green connected • LED: 2nd Battery green DC IN green DC IN green 2nd Battery •...

  • Page 115: Power Indicators

    When the main battery is not charging. For the computer to shut down in Hibernation Mode, the Hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a 2nd battery are installed, the computer does not shut down until the charge in both batteries is exhausted.

  • Page 116: Dc In Indicator

    Power and Power-Up Modes The battery charge is low. The AC adaptor must Flashing orange be connected to recharge the battery. Indicates the AC adaptor is connected and Orange charging the battery. Indicates the AC adaptor is connected and the Green battery is fully charged.

  • Page 117: Battery Types

    Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status: Indicates power is being supplied to the computer Green and the computer is turned on. Indicates power is being supplied to the computer Flashing orange while the computer is in Standby Mode.
  • Page 118 The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Always use the battery pack supplied as an accessory or an equivalent battery pack specified in the User’s Manual.
  • Page 119 The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.

  • Page 120: Care And Use Of The Battery Pack

    Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance.
  • Page 121 Do not turn on the PC’s power again until an authorized Toshiba service provider has checked it for safety. Continued use could cause a fire or rupture possibly resulting in serious injury or PC failure including but not limited to the loss of data.
  • Page 122 16. Keep the battery pack out of reach of infants and children. It can cause injury. Caution 1. Use only battery packs recommended by TOSHIBA as replacements. 2. When installing a battery pack or before moving the PC, always make sure the battery pack is inserted correctly and securely. If the battery falls out, while you are carrying the PC, you could be injured or the battery pack could be damaged.

  • Page 123: Charging The Batteries

    The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.

  • Page 124: Battery Charging Notice

    Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.

  • Page 125: Maximizing Battery Operating Time

    ■ How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options: ■...

  • Page 126: Retaining Data With Power Off

    Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Retention time Battery type State and Retention Time about 12 days (Standby Mode) High capacity battery pack (8800mAh) about 115 days (Boot mode) about 9 days (Standby Mode)

  • Page 127: Replacing The Battery Pack

    Power and Power-Up Modes ■ If you are not going to use the computer for more than eight hours, disconnect the AC adaptor. ■ Store spare battery packs in a cool dry place out of direct sunlight. Replacing the battery pack The battery pack is classified as a consumable item.

  • Page 128: Toshiba Password Utility

    Windows password. User Password To start the utility, point to or click the following items: start -> All Programs -> TOSHIBA -> Utilities -> Password Utility The User Password dialog box contains two main fields: User Password and User Token.
  • Page 129 ■ If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE. TOSHIBA will NOT be held...

  • Page 130: Supervisor Password

    If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: start ->...

  • Page 131: Power-Up Modes

    Power and Power-Up Modes Starting the computer by password If you have already registered a password, there are three ways to start the computer: ■ Insert an SD card token before you turn on the computer. The computer will start normally, without displaying a password prompt. ■...

  • Page 132: Panel Power On/Off

    Power and Power-Up Modes Windows utilities You can configure various settings associated with both Standby Mode and Hibernation Mode within TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby Mode and Fn + F4 to enter Hibernation.

  • Page 133: Chapter 7 Hw Setup

    Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability and TPM. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.

  • Page 134: Power On Display

    HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory Default settings. Display the HW Setup version. About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor.

  • Page 135: Boot Priority

    HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> The computer looks for bootable files in the CD-ROM −> LAN following order: HDD, floppy disk drive* CD-ROM* and LAN (Default).
  • Page 136 HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Slim Select Bay HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot.
  • Page 137 HW Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. The priority is set as built-in HDD ->...
  • Page 138 HW Setup Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting an Fn key equivalent will let you use Hot keys by pressing the set combination instead of the Fn key (PS/2 keyboard only).
  • Page 139 HW Setup This function lets you set the CPU operating mode. This option is displayed only on models with an Intel Core Duo processor. Dynamic CPU Frequency Mode This option lets you choose from the following settings: CPU power consumption and clock speed Dynamically automatic switching function is enabled.

  • Page 140: Device Config

    HW Setup Device Config Device Configuration This option lets you set the device configuration. BIOS sets all devices. All Devices Operating system sets devices that it can control Setup by OS (Default). Parallel/Printer Some models are equipped with Parallel/Printer tab. This tab lets you set the Parallel Port Mode.

  • Page 141: Configuring The Execute-Disable Bit Capability And Tpm

    ■ In most cases, changes to the system’s configuration should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth. If you make changes to the configuration through the BIOS setup program, please be aware that the configuration set through the Windows applications will take priority.

  • Page 142: Security Controller

    Capability so that it is not available for use. (Default). System configuration changes, other than changes to this setting, should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth.

  • Page 143: Diagnostic Mode

    ■ System configuration changes other than changes to this setting should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. ■ When using TPM, please install the Infineon TPM Installation Guide from the TOSHIBA Application Installer.
  • Page 144 HW Setup 7-12 User’s Manual...

  • Page 145: Chapter 8 Optional Devices

    Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ PC card ■ ExpressCard ■ SD card ■...

  • Page 146: Pc Card

    The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.

  • Page 147: Expresscard

    ExpressCard The computer is equipped with an ExpressCard slot. Any ExpressCard that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports hot plug connection and utilizes the PCI-Express interface that supports the reading and writing of data at a theoretical maximum rate of 2.5 Gbps.

  • Page 148: Removing An Expresscard

    Optional Devices To insert an ExpressCard, follow the steps below: 1. Insert an ExpressCard in the ExpressCard card slot. 2. Press gently to ensure a firm connection. ExpressCard slot ExpressCard Inserting an ExpressCard 3. After inserting the ExpressCard, refer to the ExpressCard’s documentation and check the configuration in Windows to make sure it is appropriate for your ExpressCard.

  • Page 149: Sd Card

    TOSHIBA SD memory card format utility, not with the format commands provided within Windows. In order to run TOSHIBA SD memory card format, click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD memory card Format.

  • Page 150: Removing An Sd Card

    Optional Devices ■ Make sure the SD card is oriented properly before you insert it. ■ Do not turn the computer off or switch to Standby Mode or Hibernate Mode while files are being copied - doing so may cause data to be lost. Removing an SD card To remove an SD card, follow the steps below.

  • Page 151: Memory Expansion

    Do not touch the metal part or expose it to liquids or let it get dirty. Creation of a boot disk Within the TOSHIBA SD Memory Boot Utility, a bootable SD memory card can be created if required. Refer to the...

  • Page 152: Installing Memory Module

    Optional Devices Use a #0 point Phillips screwdriver to remove and fasten the screws. Use of an incorrect screwdriver can damage the screw heads. Installing memory module There are slots for two memory modules, one over the other. The procedures are the same for installing either module. 1.

  • Page 153: Removing Memory Module

    Optional Devices Align the grooves along the edges of the memory module with the locking tabs on the connector and insert the module into the connector firmly. If you find it difficult to install the memory module, gently prize the locking tabs outwards using the tip of your finger.

  • Page 154: Battery Pack

    Optional Devices 4. Loosen the screw securing the memory module cover. The screw is attached to the cover to prevent it from being lost. 5. Slide your fingernail or a thin object under the cover and lift it off. 6. Push the latches to the outside to release the module. A spring will force one end of the module up.

  • Page 155: Ac Adaptor

    Optional Devices AC adaptor If you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load. Battery charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer.

  • Page 156: Installing The Hard Disk Drive Pack

    Optional Devices 8. With the hard disk drive in a vertical position, lift it straight up and away from the connector. Plastic tab Hard disk drive pack Removing the hard disk drive pack Installing the hard disk drive pack To install the hard disk drive pack, follow the steps below. 1.

  • Page 157: Slim Select Bay Hdd Adaptor

    Optional Devices Slim Select Bay HDD adaptor You can increase your computer's data storage capacity by installing an additional hard disk drive in the Slim Select Bay. To install an hard disk drive in the Slim Select Bay HDD adaptor follow the steps below. 1.

  • Page 158: Usb Floppy Disk Drive

    Optional Devices 3. Close the lid and slide the lock to the lock position. Closing the lid For details on inserting the Slim Select Bay HDD adaptor in the computer’s Slim Select Bay slot, refer to Chapter 4, Operating Basics. USB floppy disk drive The USB floppy disk drive module can be connected to the USB port.

  • Page 159: Using The Toshiba Assist Button Or Toshiba Presentation

    2. Connect the TV adaptor cable’s S-Video plug to the Video-out jack on the TV. 3. Press the TOSHIBA Assist button or TOSHIBA Presentation button. You can use the hot keys Fn + F5 to change the display device. Refer to Chapter 5, Keyboard.

  • Page 160: Displaying Movies On A Tv Or Crt

    Optional Devices If a television is connected to the computer, set the TV type in Display Properties. Follow the steps below. a. Click start and click Control Panel. b. Double-click the Display icon to open the Display Properties window. Click the Settings tab and click the Advanced button. d.

  • Page 161: I.link (Ieee1394)

    There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
  • Page 162 Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) port i.LINK (IEEE1394) connector Connecting the i.LINK (IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■...

  • Page 163: Advanced Port Replicator Iii Plus

    Optional Devices Advanced Port Replicator III Plus In addition to the ports available on the computer, the Advanced Port Replicator III Plus provides serial port and separate ports for PS/2 mouse and PS/2 keyboard. The Advanced Port Replicator III Plus connects directly to the docking interface on the underside of the computer.

  • Page 164: Serial Devices

    Optional Devices Serial devices The serial port can be used to connect to serial (RS-232C compatible) devices. RS-232C compatible devices include the following: ■ Modem ■ Mouse To connect a serial device, follow the steps below. 1. Turn the computer’s power off. 2.

  • Page 165: Troubleshooting

    Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

  • Page 166: Preliminary Checklist

    Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.

  • Page 167: Hardware And System Checklist

    Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your PC. Use of incompatible devices may cause injury or may damage your PC.

  • Page 168: Self Test

    This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...

  • Page 169: Ac Power

    Troubleshooting If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer. Computer shuts down Indicates a problem with the heat dispersal and its DC IN indicator system. Please contact your dealer. is flashing green AC power If you have trouble turning on the computer with the AC adaptor connected,...
  • Page 170 Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. User’s Manual...

  • Page 171: Real Time Clock

    5. Press Y key. BIOS setup will terminate and the computer will be rebooted. Password Problem Procedure Cannot enter Refer to the TOSHIBA Password Utility section in password Chapter 6, Power and Power-Up Modes. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Keyboard.

  • Page 172: Internal Lcd Display Panel

    Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor.
  • Page 173 Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD/DVD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical disk drive icon in the task tray and turn on the power.
  • Page 174 Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.
  • Page 175 Troubleshooting Some CD/DVDs run The software or hardware configuration may be correctly, but others do causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video...
  • Page 176 Troubleshooting Problem Procedure You cannot read a file Make sure the target file is on the SD memory card inserted in the slot. If problems persist, contact your dealer. PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected.

  • Page 177: Dual Pointing Device

    Device tab. Then click the Detail Setting button and click the Device Select tab. Check that the Touch Pad is not selected. Pressing Fn + F9 to enables TOSHIBA Dual Pointing Device. On-screen pointer The system might be busy. If the pointer is...

  • Page 178: Usb Mouse

    Troubleshooting USB mouse Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume its mouse operation normal shape and try again to move it. Make sure the mouse is properly connected to the USB port.

  • Page 179: Usb Device

    Troubleshooting USB device Refer also to your USB device’s documentation. Problem Procedure USB device does not Check for a firm cable connection between the work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed.
  • Page 180 Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Check Windows Device Manager.
  • Page 181 Troubleshooting i.LINK (IEEE1394) device Problem Procedure i.LINK device does not Make sure the cable is securely connected to the function computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon.

  • Page 182: Wireless Lan

    Troubleshooting Problem Procedure Character display In data transmission, make sure the parity bit and becomes garbled stop bit settings correspond with those of the during a remote computer. communication Check the flow control and communication session protocol. You cannot receive an Check the rings before auto answer setting in incoming call your communications application.

  • Page 183: Tv Output Signal

    Troubleshooting Bluetooth For more information on Bluetooth wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Make sure the computer’s wireless Bluetooth device communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on.

  • Page 184: Toshiba Support

    All data deletion costs will be borne by you. TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.

  • Page 185: Chapter 10 Legal Footnotes

    86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - please refer to your PC documentation or visit the Toshiba website at www.pcsupport.toshiba.com for details). User’s Manual...

  • Page 186: General Main Memory

    Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.

  • Page 187: Lcd

    Legal Footnotes Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. The screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
  • Page 188 Legal Footnotes 10-4 User’s Manual...

  • Page 189: Specifications

    Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight 2.37 kilograms, configured with: 14.1” XGA, 512MB RAM, (typical) 40GB HDD, DVD-ROM&CD-R/RW, Wireless LAN. Weight will vary with other configurations. Above weights are measured at specific criteria. They are not guaranteed as the maximum weight of the actual product.

  • Page 190: Power Requirements

    Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.0 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands...
  • Page 191 Specifications Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output 600 ohms ±30% impedance Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.3V (supplied by computer) User’s Manual...
  • Page 192 Specifications User’s Manual...

  • Page 193: Appendix B Display Controller And Modes

    Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. The display controller supports VGA, SVGA and XGA modes on the internal LCD display panel. Two models are available: ■...
  • Page 194 Display Controller and Modes Table1 Video modes (VGA) Video Type Resolution Character Colors Scanning frequency mode matrix (pels) Vertical (Hz) 0, 1 40 × 25 8 × 8 16 of 256K Text Characters 2, 3 80 × 25 8 × 8 16 of 256K Text Characters...
  • Page 195 Display Controller and Modes Table1 Video modes (VGA) continued Video Type Resolution Character Colors Scanning frequency mode matrix (pels) Vertical (Hz) 320 × 200 8 × 8 16 of 256K Grph Pels 640 × 200 8 × 8 16 of 256K Grph Pels 640 ×...
  • Page 196 Display Controller and Modes Table 2 Video modes (XGA model) Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K (Virtual with LCD only) 1600 ×...
  • Page 197 Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K (Virtual with LCD only) 1600 ×...
  • Page 198 Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M (Virtual with LCD only) 1600 ×...
  • Page 199 Display Controller and Modes Table 3 Video modes (SXGA+ model) Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K 1440 × 1050 256/256K 256/256K 1600 ×...
  • Page 200 Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K 1440 × 1050 64K/64K 64K/64K 1600 ×...
  • Page 201 Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M 1440 × 1050 16M/16M 16M/16M 1600 ×...

  • Page 202: Powermizer

    Display Controller and Modes PowerMizer PowerMizer is a graphics processor installed on this computer. The performance of PowerMizer can be configured in three ways. To define the performance, select the menu options shown below: Display Property -> Settings -> Advanced -> Quadro NVS 110M tab -> Quadro NVS 110M button ->...

  • Page 203: Wireless Lan

    Appendix C Wireless LAN Card Specifications Form Factor PCI-Ex MiniCard Type ■ IEEE 802.11 Standard for Wireless LANS Compatibility ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The “Wi-Fi CERTIFIED” logo is a certification mark of the Wi-Fi Alliance. ■...

  • Page 204: Radio Characteristics

    Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.

  • Page 205: Supported Frequency Sub-Bands

    Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
  • Page 206 Wireless LAN Wireless IEEE 802.11 Channels Sets (Revision A) Frequency Range 5150-5850 MHz Channel ID 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825 User’s Manual...

  • Page 207: Bluetooth Wireless Technology Interoperability

    Appendix D Bluetooth wireless technology Interoperability Bluetooth™ Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver2.0+EDR, as defined and approved by The Bluetooth Special Interest Group.
  • Page 208 TOSHIBA portable computers. Always use Bluetooth™ Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe...

  • Page 209: Bluetooth Wireless Technology And Your Health

    Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
  • Page 210 ■ Consult the dealer or an experienced radio/TV technician for help. TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Bluetooth™ Card from TOSHIBA, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA.
  • Page 211 The radiated output power of the Bluetooth™ Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth™ Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized. In normal operating configuration, the LCD in the upright position, the distance between the antenna and the user should not be less than 20cm.

  • Page 212: Using Bluetooth™ Card From Toshiba Equipment In Japan

    3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.

  • Page 213: Device Authorization

    Bluetooth wireless technology Interoperability 3. TOSHIBA Direct PC Monday - Friday : 10:00-17:00 Toll Free Tel : 0120-15-1048 Direct Dial : 03-3457-4850 : 03-3457-4868 Device Authorization This device obtains the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law.
  • Page 214 Bluetooth wireless technology Interoperability User’s Manual...

  • Page 215: Ac Power Cord And Connectors

    Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters...
  • Page 216 AC Power Cord and Connectors In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S.
  • Page 217 BIOS and Hard Disk Drive to gain access to the system. To set permission and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility. The settings can only be activated or modified by a user with supervisor authority.
  • Page 218 TOSHIBA Anti-theft Protection Timer User’s Manual...

  • Page 219: If Your Computer Is Stolen

    What is your address, phone, and fax number? To register the theft on paper, please follow these procedures: ■ Fill in the TOSHIBA Theft Registration form (or a copy of it) below. ■ Attach a copy of your receipt showing where your computer was purchased.

  • Page 220: Toshiba Theft Registration

    If your computer is stolen TOSHIBA Theft Registration Send to: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany Fax number: +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. Satellite A50) Model number: (e.g. PSA50 YXT) Serial number: (e.g.
  • Page 221 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only Memory CD-RW: Compact Disc-ReWritable...
  • Page 222 VRT: voltage reduction technology WXGA: wide extended graphics array XGA: extended graphics array AccuPoint: A pointing device integrated into the TOSHIBA computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
  • Page 223 Glossary ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity. application: A group of programs that together are used for a specific task such as accounting, financial planning, spreadsheets, word processing and games.
  • Page 224 Glossary byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory.
  • Page 225 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
  • Page 226 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
  • Page 227 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
  • Page 228 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
  • Page 229 Glossary I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. I/O devices: Equipment used to communicate with the computer and transfer data to and from it. IrDA 1.1: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps.
  • Page 230 Glossary megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. menu: A software interface that displays a list of options on the screen. Also called a screen. microprocessor: A hardware component contained in a single integrated circuit that carries out instructions.
  • Page 231 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
  • Page 232 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to.
  • Page 233 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
  • Page 234 Glossary Glossary-14 User’s Manual...
  • Page 235 B-1 Advanced Port Replicator III hinge, 2-8 Plus, 1-17, 8-19 opening, 3-8 ASCII characters, 5-9 screen, 2-9 DLA for TOSHIBA, 1-16, 4-23 Docking interface, 1-7, 2-7 Battery Documentation list, 1-2 charging, 6-11 Dual Pointing Device, 1-7 extending life, 6-14...
  • Page 236 Index Fn + space (LCD screen resolution selection), 5-6 Environment, 3-1 Fn + Tab (Optical media drive Equipment checklist, 1-1 power icon), 5-6 Equipment setup Function keys, 5-2 general conditions, 3-2 placement, 3-3 Ergonomics Graphics controller, 1-6 lighting, 3-5 seating and posture, 3-4 work habits, 3-5 Hard disk drive, 1-4, 1-17 ExpressCard, 1-7, 8-3...
  • Page 237 Index Memory, 1-3 expansion, 1-16, 8-7 i.LINK, 1-7, 2-3, 8-17 problems, 9-15 connecting, 8-18 Modem, 1-8, 4-29 disconnecting, 8-18 connecting, 4-30 precautions, 8-17 disconnecting, 4-32 problems, 9-17 jack, 2-5 Indicators, 2-11, 6-3 problems, 9-17 properties menu, 4-30 region selection, 4-29 Keyboard, 1-7, 5-1 Moving the computer, 4-37 emulating enhanced...
  • Page 238 7-8 Self test, 9-4 Problems Sound system, 9-16 AC power, 9-5 System start-up, 9-3 AccuPoint, 9-13 TOSHIBA support, 9-20 Analyzing symptoms, 9-2 Touch Pad/AccuPoint, 9-13 Battery, 9-5 TV output signal, 9-19 Bluetooth, 9-19 USB, 9-15 Dual Pointing Device, 9-13...
  • Page 239 3-10 Volume control, 2-4 System automatic, 1-10 Wireless communication, 4-32 TOSHIBA Assist, 1-14 indicator, 2-11, 4-35 TOSHIBA Assist button, 1-10 Wireless communication switch, TOSHIBA ConfigFree, 1-15 1-9, 2-1, 4-34 TOSHIBA Controls, 1-13 Wireless LAN, 1-9, 4-32 TOSHIBA Dual Pointing Device...
  • Page 240 Index Index-6 User’s Manual...

Table of Contents