System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Instructions This document contains basic product and configuration information that will enable you to configure your system via PC-/SystemArchitect. Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system.
Page 3
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Configuration diagram PRIMERGY System unit ( 3.5" HDDs ) SIDE VIEW FRONT VIEW Hot plug power supplies 3 x 5.25" bays available 3 x HH 5.25" free 2 x HH 5,25"...
Page 4
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Configuration diagram PRIMERGY System unit ( 2.5" HDDs ) SIDE VIEW FRONT VIEW Hot plug power supplies 3 x 5.25" bays available 3 x HH 5.25" free or 2 x HH 5.25"...
Page 5
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Start PRIMERGY SW Configurator 32 bit with OEM-Software without OEM-Software for PRIMERGY Server for PRIMERGY Server OEM- SW is bound to HW and VMware-Software is not allowed to be ordered - VirtualCenter Management Server for any server released for Windows Server 2003 separately.
Page 6
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Start PRIMERGY TX300 S7 SW Configurator 64 bit (EM64T / IA64) with OEM-Software without OEM-Software for PRIMERGY Server for PRIMERGY Server OEM- SW is bound to HW and...
Page 7
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Start PRIMERGY TX300 S7 Section Basic units SAS - System unit, Rack and Floorstand including: * By a key lockable front bezel in floorstand version * Basic units with: - 4 Hot-Plug Power Supply Slots - 4 Standard Fans (92mm;...
Page 8
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Interfaces at the rear: * 1x RS-232-C (serial, 9 pins) (usable for BMC or OS or shared) * 1x RS-232-C (serial, 9 pins) * 1x VGA (15 pins) * 4x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup...
Page 9
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 TX300 S7 Floorstand System RX350 S7 Rack System without CPU, Memory and PSU without CPU, Memory and PSU with: with: - Four hot plug fans (no redundancy)
Page 10
For later conversion the following kits are available: 1.) Conversion kit 2 Floor -> Rack S26361-F1729-L260 Conversion PRIMERGY TX300 S7 base unit floorstand into base unit rack. Only conversion, no mounting kit. Mounting kit has to be ordered seperatly. Fujitsu PRIMERGY Server...
Page 11
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 For min. configuration one power supply has to be selected For basic redundancy at least 2 PSUs of the same type have to be configured There is only one PSU type (450W or 800W) allowed...
Page 12
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Section Processor There are 2 processor sockets available. The first socket is always equipped with the first CPU which can be selected via configurator It is also possible to upgrade a dual-processor system later on with a second CPU Two processors with different type are not possible If CPU's with a TDP >= 130W are used (e.g.
Page 13
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Section Memory - There are 12 memory slots per CPU for max. 384GB LRDIMM (12x 32GB 4R) 192GB RDIMM (12x 16GB 2R) 32GB UDIMM (8x 4GB) => max. 768GB for two CPU`s ( 384GB per CPU ), using LRDIMM...
Page 14
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 S26361-F3694-E10 Independent Mode Independent Channel Mode allows all channels to be populated in any order. No specific Memory RAS features are defined Requires min 1 memory Module per CPU...
Page 15
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Memory Configuration PRIMERGY TX300 S7 / RX350 S7 Each CPU offers 12 Slots for DDR3 Memory Modules organised in 3 Banks and 4 Channels. If you need more than 12 Slots you have to configure the 2nd CPU.
System configurator and order-information guide 1. Independent Channel Mode PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 required required if 2nd CPU is configured Bank I Data Data Data Data Data Data Data Data optional, same type in Bank per CPU...
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 4. Rank Sparing Mode 1-Rank Memory modules (RDIMM) required required if 2nd CPU is configured Bank I optional, same type in Channel per CPU Spare Spare Spare...
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Section Graphics & GPGPU & Co-Processors Graphics Controller integrated in iRMC S3 (integrated Remote Management Controller) with following resolutions: 1920x1200x16bpp, 1920x1080x16bpp, 1600x1200x16bpp, 1680x1050x16bpp, 1440x900x16bpp, 1280x1024x32bpp, 1152x864x16bpp, 1024x768x32bpp, 800x600x32bpp, 640x480x32bpp...
Page 19
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Intel Xeon Phi Co-processor One or two GPGPU (General Purpose Graphical Processor Unit) can be ordered as option. The Power Cable kit has to be ordered seperatly and will be installed if ordered ex factory together with the GPGPU card.
Page 20
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Section Accessible drives and 3.5" SAS / SATA HDD extension box There are 3 bays (1.6" x 5.25") for accessible drives. see Conf. Diagram Option A see Conf. Diagram Option B see Conf.
Page 21
System Configurator and Order-Information Guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 data cartridges must be ordered S26361-F3325-E4 separately Tape drive DDS Gen6 USB 5.25" 80GB, 6MB/s, USB 2.0 Connector: USB "B" with USB cable incl. cleaning cartridge without data cartridge 1.6 * 5.25", black bezel...
Page 22
System Configurator and Order-Information Guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 For internal SAS Backup drives an additional 4-port SAS controller has to be configured SAS Controller for internal Backup Drives S26361-F3674-E1 Onboard 4 port SAS Controller LSI SW RAID Patsburg B RAID 0, 1 &...
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Section Modular Raid Controller for 3.5" Hard Disks On board SATA Controller can be used with up to 4x 3.5" SATA HDDs (no additional controller required) For up to 4x 3.5" SAS HDDs with RAID 0/1 functionality a Patsburg Upgrade Kit is required (no SAS tape option)
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Section Modular Raid Controller for 2.5" Hard Disks For internal 2.5" hard disks one of the following modular RAID-controllers is required as long as available as soon...
Page 25
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 S26361-F2826-E325 see Conf. diagram Option E SFF (2.5") HDD-Box for additional 8x SFF (2.5") SAS hard disks Occupies 2.5" HDD extension area 24x SAS Expander for loose delivery please order max.
Page 26
System Configurator and Order-Information Guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 VIII Section 3.5" SAS / SATA Hard disk drives In a basic unit 4x 3.5" HDDs can be configured. With Option D additional 4x 3.5" HDDs are possible.
Page 27
System Configurator and Order-Information Guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Section 2.5" SAS / SATA Hard disk drives Up to 24x 2.5" SAS/SATA hard disks can be configured. S26361-F4541-E100 S26361-F4541-E400 **) High Endurance SSD SAS 100GB, SLC...
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Section External SAS Disk Array & Backup drives SAS RAID controller for JBOD subsystems as long as available as soon as available S26361-F3593-E1 S26361-F3713-E1 S26361-F3713-E3 RAID Ctrl SAS 6G 8port external RAID Ctrl SAS 6G 8port external RAID Ctrl SAS 6G 8port ext.
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Section Fibre Channel Controller for external storage systems Only a single vendor for FC and All controllers for the connection of external FCoE controller is supported. storage system are delivered without cables.
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Section Communication / Network Modular On-Board LAN is a flexible extension of a cost-optimized Motherboard 2x Gigabit (Dualport) Ethernet Contr. with basic 2x Gbit LAN on-board. onboard...
Page 31
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 If a 10Gb modular LAN Controller is installed, max. 1 additional of the following 10Gb LAN controller is possible! S26361-F3629-E2 E) 10GbE 2-Port SFP+ S26361-F3629-E2 (D2755) 10 Gigabit Ethernet Contr. dual port SFP+ Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+ All controllers for the connection of external storage systems are delivered without cables.
Page 32
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 G) Fibre Channel over Ethernet S26361-F3592-E2 Loose delivery S26361-F3592-L2 10GBit/s CNA Emulex OCe10102 2 channel 10GBit/sec CNA SFP+ Cage PCIe x8, 170mm max. 4 per system S26361-F3592-E108...
Page 33
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 H) Infiniband HCA's S26361-F4475-E102 S26361-F4475-E122/E222 loose delivery: S26361-F4475-L102 IB HCA 40Gb 1 port QDR PIB EP QLE7340e/42e loose delivery: S26361-F4475-L122/L222 IB HCA 1x 40Gb Intel IB HCA 1x / 2x 40Gb PCIe 2.0 (5,0GT/s)
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 XIII Section System Management Products (RemoteView) iRMC S3 (integrated Remote Management Controller) onboard server management Controller with dedicated 10/100/1000 Service LAN-port and integrated graphics. Optional 10/100 Service LAN-port on front panel.
Page 35
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Section Country specific options as soon as available Since the beginning of this year the specifications for the approval and production monitoring for S26361-F3301-E120 China (CCC) have become stricter. This is why the...
System configurator and order-information guide PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30 Change Report Date Order number Changes 2013-10-18 PCIe lenght corrected 2013-10-18 Optional USB Comps no longer available S26361-F4610-E2 / -E4 2013-10-16 added new 1Gb NICs from Intel...