Table of Contents
Advertisement
C
S
C
h
ettiNG
oNtaCt
2:
a
DjuStmeNt
R
f
eVeRSe
uNCtioN
NOTE
Limit Switch and Force Adjustments must be completed before
checking the contact reverse function .
A
Open garage door using Wall Console .
B
Lay a 2” x 4” board flat in center of doorway (Figure 10) .
C
Close door using Wall Console .
D
Check that door stops and reverses within 2 seconds after it
contacts board:
•
If door does not reverse, decrease Close Force until
door reverses (Figure 9) .
•
If door still does not reverse, move Limit Switch
toward door .
E
Check Safe-T-Beam® System operation:
•
If beam is blocked, door
will not close .
Figure 10
Checking
2” x 4” board
Contact
laid flat
Reverse
NOTE
The door must contact the 2” x 4” board before the
Carriage activates the Close Limit Switch . If not,
readjust the Close Limit Switch .
a
CCeSSoRieS
C
p
h
RoGRammiNG the
Programming 1:
R
C
emote
oNtRol
A
To program one Button of a Remote Control (Figure 11):
•
Locate Learn Button and Learn Indicator Light near
Terminal Block on Power Head (Figure 12) .
•
Press and release Learn Button . Red Learn Indicator Light
will blink 2 times per second .
•
Press Remote Control Button once within 30 seconds . Red
Learn Indicator Light will stay lit .
•
Press Remote Control Button again . Red Learn Indicator
Light will go out, indicating that memory is stored .
•
Press again to Activate Unit .
B
Program each additional Remote using step A above .
To Erase All Remotes from Power Head Memory
A
Press and hold Learn Button on Power Head for 10 seconds
or until Learn Indicator Light goes out . Memory is erased:
•
Program Remotes again as needed .
To Replace Remote Control Battery
A
FOR NON-FLASHLIGHT MODELS
•
Pop off the back of the transmitter .
–
Use coin, pen, screwdriver or any similar device .
–
Replace old Battery with new coin type battery .
•
Replace back of remote.
B
FOR FLASHLIGHT MODELS
•
Slide open battery cover .
–
Replace old Battery with new AAA battery .
•
Replace battery cover.
WARNING
A moving garage door may cause serious injury or death .
• Keep people clear of opening while door is moving .
• Do not allow children to play with the Remote Controls .
If the Safety Reverse does not work properly:
• Close the door and disconnect the Opener using the
Emergency Release Cord .
• Do not use the door Opener, Remote Controls, or
Wireless Keypad .
• Refer to the door and door Opener Owner’s Manuals
before attempting any repairs .
Remote Control Operation
A
Press Button on Remote Control . Garage door will move .
B
Press Button again . Garage door will stop:
•
The door automatically stops at the end of the
open or close cycle .
C
Press Button again . Garage door will reverse .
Figure 11
1-Button and 3-Button
Compact Remotes
w/Docking Station
D
There are several additional varieties of remote controls
available from your local dealer, some equipped with
a flashlight .
OPEN
LEARN
INDICATOR
CLOSE
LIGHT
LEARN
CODE
BUTTON
Figure 12 Learn Code Button and Indicator Light .
(Located Lower Right Corner) .
NOTE
• Each Remote Control must be programmed
separately .
• The Remote Controls will not close the garage with
malfunctioning Safe-T-Beam® System .
• Program Remote Controls, while at least 24” from
Antenna Wire .
• If the red Learn Indicator Light blinks rapidly,
programming stopped . Restart programming .
• Each Button on a multi-button Remote Control is
for a different Opener . Cannot use more than one
Button for same Opener .
• A maximum of seven Remote Controls or Wireless
Keypads can be stored into the Receiver at one
time . If a Remote Control becomes lost, or if you
want to delete a Remote Control or Wireless
Keypad, see “To Erase All Receiver Memory . ”
Page 8
Hide quick links:
Advertisement
Table of Contents
